Effect of grain distribution on resin consumption and mechanical performance of GRP pipes

Carbon nanotubes (CNTs) reinforced aluminum matrix nanocomposites were fabricated by Accumulative Roll Bonding (ARB). The surface morphologies, mechanical properties, grains texture and orientation of the Al/CNTs nanocomposites were characterized, and the mechanisms and influences of CNTs contents and ARB cycles on the mechanical performance and grain textures of Al/CNTs were investigated and revealed. The strength of the composites rose with increase of the CNTs content, and the ARB cycles showed a 26% improvement when the CNTs content varied from 0 to 1 volume percent (vol.%). The increase in the mass fraction of the carbon nanotubes made the grain distribution in the Al/CNTs nanocomposite samples more diffuse. Besides, the stable texture of the hot rolled crystal grains on the α orientation are constantly turning to {011}< 011> with the mass fraction of the reinforcing phase increased.

Download Full-text

Incorporation of Cholesterol into Peripheral Nerve Myelin

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100094930 ◽

1972 ◽

Vol 30 ◽

pp. 334-335

Author(s):

Frank A. Rawlins

Keyword(s):

Electron Microscope ◽

Sciatic Nerve ◽

Electron Microscope Autoradiography ◽

Myelin Sheaths ◽

Microscope Autoradiography ◽

Grain Distribution ◽

Sciatic Nerves ◽

Autoradiographic Analysis ◽

Old Mice ◽

Short Times

Several speculations exist as to the site of incorporation of preformed molecules into myelin. The possibility that an autoradiographic analysis of cholesterol-1,2-H3 incorporation at very short times after injection might shed some light in the solution of that problem led to the present experiment.Cholesterol-1,2-H3 was injected intraperitoneally into 24 tenday old mice. The animals were then sacrificed at 10,20,30,40,60,90,120 and 180 min after the injection and the sciatic nerves were processed for electron microscope autoradiography. To analyze the grain distribution in the autoradiograms of cross and longitudinal sections from each sciatic nerve myelin sheaths were subdivided into three compartments named: outer 1/3, middle 1/3 and inner 1/3 compartments.It was found that twenty min. after the injection of cholesterol -1.2-H3 (Figs. 1 and 2), 55% of the total number of grains (t.n.g) found in myelin were within the outer 1/3 compartment, 9% were within the middle 1/3 and 36% within the inner 1/3 compartment

Download Full-text

271 Cardiac re-synchronization may have a beneficial effect on right ventricular mechanical performance

EP Europace ◽

10.1016/s1099-5129(05)80191-6 ◽

2005 ◽

Vol 7 ◽

pp. 65-65

Keyword(s):

Beneficial Effect ◽

Right Ventricular ◽

Mechanical Performance

Download Full-text

The Mechanical Performance of Carbon Fibres- Addressing the Role of Microstructure

10.33599/nasampe/s.19.1459 ◽

2019 ◽

Author(s):

Peter Peter ◽

Claudia Creighton ◽

David Fox ◽

Pablo Mota Santiago ◽

Adrian Hawley ◽

...

Keyword(s):

Mechanical Performance ◽

Carbon Fibres

Download Full-text

Microstructural and Mechanical Behaviour Evaluation of Mg-Al-Zn Alloy Friction Stir Welded Joint

International Journal of Automotive and Mechanical Engineering ◽

10.15282/ijame.17.3.2020.08.0612 ◽

2020 ◽

Vol 17 (3) ◽

pp. 8150-8159

Author(s):

Kulwant Singh ◽

Gurbhinder Singh ◽

Harmeet Singh

Keyword(s):

Heat Treatment ◽

Friction Stir Welding ◽

Magnesium Alloys ◽

Mechanical Performance ◽

Fuel Efficiency ◽

Research Work ◽

Grain Structure ◽

Tensile Fracture ◽

Friction Stir ◽

The Impact

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.

Download Full-text