scholarly journals ACOUSTIC EMISSION AND DAMAGE CHARACTERISTICS OF ANTHRACITE UNDER DIFFERENT CONDITIONS

2021 ◽  
Vol 55 (2) ◽  
pp. 213-218
Author(s):  
Jiyu Zheng ◽  
Xiaohua Jin ◽  
Kunyun Tian ◽  
Yinbo Zhou
Keyword(s):  
Acoustic Emission ◽  
Coal Sample ◽  
Characteristic Curve ◽  
Great Influence ◽  
Acoustic Emissions ◽  
Slow Increase ◽  
Loading Rates ◽  
The Relationship ◽  
Damage Characteristic ◽  
Peak Count

Acoustic emission (AE) can be used to observe the process of coal fracture propagation. Based on a press and acoustic-emission platform, the damage and acoustic-emission characteristics of anthracite with different loading rates, water amounts and sizes were studied. The results show that there is less acoustic emission in the initial compression stage of coal; acoustic emission is more active in the transition from elastic deformation to plastic deformation, which is manifested in the following aspects: the faster the loading rate, the higher is the number of acoustic-emission events; the peak count of acoustic emissions of a saturated-coal sample is significantly lower than that of a natural-coal sample. Coal samples and large coal samples emit even more sounds. Based on the normalization of acoustic-emission counts, the relationship between damage variables and stress-strain is studied, and it is characterized by an initial slow increase, followed by a rapid increase; however, different factors have a great influence on the damage-characteristic curve. The research results have a certain guiding significance for the coal and rock disaster prediction.

scholarly journals Study of Acoustic Emission and Mechanical Characteristics of Coal Samples under Different Loading Rates

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Huamin Li ◽  
Huigui Li ◽  
Baobin Gao ◽  
Dongjie Jiang ◽  
Junfa Feng
Keyword(s):  
Acoustic Emission ◽  
Elasticity Modulus ◽  
Loading Rate ◽  
Peak Stress ◽  
Test System ◽  
Strong Impact ◽  
Peak Strain ◽  
Compression Tests ◽  
Loading Rates ◽  
The Relationship

To study the effect of loading rate on mechanical properties and acoustic emission characteristics of coal samples, collected from Sanjiaohe Colliery, the uniaxial compression tests are carried out under various levels of loading rates, including 0.001 mm/s, 0.002 mm/s, and 0.005 mm/s, respectively, using AE-win E1.86 acoustic emission instrument and RMT-150C rock mechanics test system. The results indicate that the loading rate has a strong impact on peak stress and peak strain of coal samples, but the effect of loading rate on elasticity modulus of coal samples is relatively small. When the loading rate increases from 0.001 mm/s to 0.002 mm/s, the peak stress increases from 22.67 MPa to 24.99 MPa, the incremental percentage is 10.23%, and under the same condition the peak strain increases from 0.006191 to 0.007411 and the incremental percentage is 19.71%. Similarly, when the loading rate increases from 0.002 mm/s to 0.005 mm/s, the peak stress increases from 24.99 MPa to 28.01 MPa, the incremental percentage is 12.08%, the peak strain increases from 0.007411 to 0.008203, and the incremental percentage is 10.69%. The relationship between acoustic emission and loading rate presents a positive correlation, and the negative correlation relation has been determined between acoustic emission cumulative counts and loading rate during the rupture process of coal samples.

scholarly journals Acoustic Emission Characteristics and Failure Mechanism of Fractured Rock under Different Loading Rates

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Yongzheng Zhang ◽  
Gang Wang ◽  
Yujing Jiang ◽  
Shugang Wang ◽  
Honghua Zhao ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Failure Mechanism ◽  
Strain Energy ◽  
Loading Rate ◽  
Fractured Rock ◽  
Acoustic Emissions ◽  
Biaxial Compression ◽  
Particle Model ◽  
Energy Rate ◽  
Loading Rates

To study the loading rate dependence of acoustic emissions and the failure mechanism of fractured rock, biaxial compression tests performed on granite were numerically simulated using the bonded particle model in Particle Flow Code (PFC). Uniaxial tests on a sample containing a single open fracture were simulated under different loading rates ranging from 0.005 to 0.5 m/s. Our results demonstrate the following. (1) The overall trends of stress and strain changes are not affected by the loading rate; the loading rate only affects the strain required to reach each stage. (2) The strain energy rate and acoustic emission (AE) events are affected by the loading rate in fractured rock. With an increase in the loading rate, AE events and the strain energy rate initially increase and then decrease, forming a fluctuating trend. (3) Under an external load, the particles within a specimen are constantly squeezed, rotated, and displaced. This process is accompanied by energy dissipation via the production of internal tensile and shear cracks; their propagation and coalescence result in the formation of a macroscopic rupture zone.

scholarly journals Research on Acoustic Emission and Electromagnetic Emission Characteristics of Rock Fragmentation at Different Loading Rates

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Fujun Zhao ◽  
Yu Li ◽  
Zhouyuan Ye ◽  
Yong Fan ◽  
Siping Zhang ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Loading Rate ◽  
Electromagnetic Emission ◽  
Rock Fragmentation ◽  
Loading Rates ◽  
Peak Intensity ◽  
Wave Forms ◽  
Show Jumping ◽  
Peak Count ◽  
Good Agreement

The relationships among the generation of acoustic emission, electromagnetic emission, and the fracture stress of rock grain are investigated, which are based on the mechanism of acoustic emission and electromagnetic emission produced in the process of indenting rock. Based on the relationships, the influence of loading rate on the characteristics of acoustic emission and electromagnetic emission of rock fragmentation is further discussed. Experiment on rock braking was carried out with three loading rates of 0.001 mm/s, 0.01 mm/s, and 0.1 mm/s. The results show that the phenomenon of acoustic emission and electromagnetic emission is produced during the process of loading and breaking rock. The wave forms of the two signals and the curve of the cutter indenting load show jumping characteristics. Both curves have good agreement with each other. With the increase of loading rate, the acoustic emission and electromagnetic emission signals are enhanced. Through analysis, it is found that the peak count rate, the energy rate of acoustic emission, the peak intensity, the number of pulses of the electromagnetic emission, and the loading rate have a positive correlation with each other. The experimental results agree with the theoretical analysis. The proposed studies can lead to an in-depth understanding of the rock fragmentation mechanism and help to prevent rock dynamic disasters.

scholarly journals The temperature- and density-dependent acoustic emission response of snow in monoaxial compression tests

2004 ◽  
Vol 38 ◽  
pp. 291-298 ◽  
Author(s):  
Carlo Scapozza ◽  
Felix Bucher ◽  
Peter Amann ◽  
Walter J. Ammann ◽  
Perry Bartelt
Keyword(s):  
Acoustic Emission ◽  
Relaxation Times ◽  
Acoustic Emissions ◽  
Wide Band ◽  
Strain Rates ◽  
Compression Tests ◽  
Load History ◽  
Fine Grained ◽  
Rate Controlled ◽  
The Relationship

AbstractResults of acoustic emission tests on cylindrical specimens under compression are reported. Deformation-rate-controlled tests with strain rates ranging from 1.1 × 10-6 s-1 to 2.6 × 10-3 s-1 at temperatures between T = -11.2°Cand T = -1.7°C were performed. The investigated snow was fine-grained, with a density varying between 220 and 380 kgm-3. The acoustic emission was measured with two distinct piezoelectric sensors: a wide-band sensor (frequency 100–1000 kHz) and a resonant sensor (frequency 35–100 kHz). The relationship between the applied strain rate and the measured maximum acoustic-emission rate as a function of temperature and density was found to obey a power law, which is valid for the ductile behaviour range. The quantitative and qualitative effects produced on the acoustic emissions during the transition from ductile to brittle behaviour, occurring at strain rates of approximately 1 × 10-3 s-1, are reported. Finally, the influence of the load history on the acoustic emissions of snow is discussed on the basis of a cyclic test, including deformation-controlled loading steps and relaxation steps, performed at different strain rates and different relaxation times.

scholarly journals Acoustic Emission Waveform Changes for Varying Seeded Defect Sizes

2006 ◽  
Vol 13-14 ◽  
pp. 427-432 ◽  
Author(s):  
S. Al-Dossary ◽  
R.I. Raja Hamzah ◽  
D. Mba
Keyword(s):  
Acoustic Emission ◽  
Acoustic Emissions ◽  
Defect Size ◽  
Geometric Size ◽  
The Relationship ◽  
Geometric Defect

The investigation reported in this paper was centered on the application of the Acoustic Emissions (AE) technology for characterising the defect sizes on a radially loaded bearing. The aim of this investigation was to ascertain the relationship between the duration of AE transient bursts associated with seeded defects to the actual geometric size of the defect. It is concluded that the geometric defect size can be determined from the AE waveform.

Evaluation of the acoustic emission caused by the chip segmentation frequency during machining of titanium alloy

2020 ◽  
Vol 87 (11) ◽  
pp. 714-720
Author(s):  
Daniel Schwär ◽  
Germán González ◽  
Eric Segebade ◽  
Frederik Zanger ◽  
Michael Heizmann
Keyword(s):  
Acoustic Emission ◽  
Titanium Alloy ◽  
Spectral Analysis ◽  
Chip Formation ◽  
Acoustic Emissions ◽  
Turning Process ◽  
Longitudinal Turning ◽  
The Relationship ◽  
Chip Analysis

AbstractThis work investigates the relationship between acoustic emission and chip segmentation frequency of Ti-6Al-4V at the external longitudinal turning process. Therefore, several sensors like structure borne sensors, microphones and a force dynamometer have been installed in a vertical turning machine. To induce a change of the segmentation frequency, several experiments with different feed rates have been carried out. From each experiment the acoustic emissions have been recorded and the generated chips have been analyzed. Since the chips get stretched or compressed during the chip formation the change in the length is calculated to get an estimation of the segmentation frequency. The comparison of the spectral analysis of the acoustic emission signals and the chip analysis has shown that both methods show the same tendency. The segmentation frequency decreases with increasing feed.

The influence of ultrasound signal parameters on sonoluminescence light intensity

2013 ◽  
Vol 62 (4) ◽  
pp. 605-612
Author(s):  
Marek Szmechta ◽  
Tomasz Boczar ◽  
Dariusz Zmarzły
Keyword(s):  
Acoustic Emission ◽  
Acoustic Waves ◽  
Power Transformer ◽  
Electrical Power ◽  
Partial Discharges ◽  
Research Project ◽  
Insulation Systems ◽  
Secondary Phenomenon ◽  
New Research ◽  
The Relationship

Abstract Topics of this article concern the study of the fundamental nature of the sonoluminescence phenomenon occurring in liquids. At the Institute of Electrical Power Engineering at Opole University of Technology the interest in that phenomenon known as secondary phenomenon of cavitation caused by ultrasound became the genesis of a research project concerning acoustic cavitation in mineral insulation oils in which a number of additional experiments performed in the laboratory aimed to determine the influence of a number of acoustic parameters on the process of the studied phenomenona. The main purpose of scientific research subject undertaken was to determine the relationship between the generation of partial discharges in high-voltage power transformer insulation systems, the issue of gas bubbles in transformer oils and the generated acoustic emission signals. It should be noted that currently in the standard approach, the phenomenon of generation of acoustic waves accompanying the occurrence of partial discharges is generally treated as a secondary phenomenon, but it can also be a source of many other related phenomena. Based on our review of the literature data on those referred subjects taken, it must be noted, that this problem has not been clearly resolved, and the description of the relationship between these phenomena is still an open question. This study doesn’t prove all in line with the objective of the study, but can be an inspiration for new research project in the future in this topic. Solution of this problem could be a step forward in the diagnostics of insulation systems for electrical power devices based on non-invasive acoustic emission method.

scholarly journals Relationship between Plasma Trimethylamine N-Oxide Levels and Renal Dysfunction in Patients with Hypertension

2021 ◽  
pp. 1-12
Author(s):  
Jia Zhou ◽  
Dingkun Wang ◽  
Bingong Li ◽  
Xuelian Li ◽  
Xingjun Lai ◽  
...  
Keyword(s):  
Blood Pressure ◽  
Kidney Disease ◽  
Renal Dysfunction ◽  
High Performance ◽  
Characteristic Curve ◽  
Area Under The Curve ◽  
Hypertensive Patients ◽  
Ckd Stage ◽  
Liquid Chromatography Tandem Mass ◽  
The Relationship

<b><i>Introduction:</i></b> Trimethylamine N-oxide (TMAO) is a metabolite produced by gut bacteria. Although increased TMAO levels have been linked to hypertension (HTN) and chronic kidney disease (CKD) with poor prognosis, no clinical studies have directly addressed the relationship between them. In this study, we investigated the relationship between TMAO and renal dysfunction in hypertensive patients. <b><i>Methods:</i></b> We included healthy controls (<i>n</i> = 50), hypertensive patients (<i>n</i> = 46), and hypertensive patients with renal dysfunction (<i>n</i> = 143). Their blood pressure values were taken as the highest measured blood pressure. Renal function was evaluated using the estimated glomerular filtration rate. Plasma TMAO levels were measured using high-performance liquid chromatography tandem mass spectrometry. <b><i>Results:</i></b> We found significant differences in plasma TMAO levels among the 3 groups (<i>p</i> &#x3c; 0.01). The plasma TMAO of patients with HTN was significantly higher than that of healthy people, and the plasma TMAO of patients with HTN complicated by renal dysfunction was significantly higher than either of the other groups. Patients in the highest TMAO quartile were at a higher risk of developing CKD stage 5 than those in the lowest quartile. In the receiver operating characteristic curve, the area under the curve of TMAO combined with β 2-macroglobulin for predicting renal dysfunction in patients with HTN was 0.85 (95% confidence interval 0.80–0.90). <b><i>Conclusion:</i></b> An elevated TMAO level reflects higher levels of HTN and more severe renal dysfunction. TMAO, combined with β 2-macroglobulin levels, may assist in diagnosing CKD in hypertensive patients. Plasma TMAO has predictive value for early kidney disease in hypertensive patients.

Study on the Prediction Method of Tunnel Surrounding Rock Pressure Based on the Theory of Progressive Destruction

2012 ◽  
Vol 446-449 ◽  
pp. 1432-1436
Author(s):  
Suo Wang
Keyword(s):  
Rock Pressure ◽  
Characteristic Curve ◽  
Prediction Method ◽  
Surrounding Rock ◽  
Progressive Damage ◽  
Tunnel Excavation ◽  
Practical Engineering ◽  
Surrounding Rock Pressure ◽  
The Relationship ◽  
Rock Parameters

In order to predict tunnel surrounding rock pressure, this paper puts forward a series of dynamic numerical simulative model on the tunnel excavation. According to the change of rock damage in the construction program, it adjusts dynamically the mechanical material parameters of surrounding rock. So the model achieves the purpose which is controlling and simulating the process of tunnel progressive damage. In accordance with the numerical simulative results, it analyzes the relationship between the rock parameters with the plastic strain, radial displacement. Then this paper proposes a prediction method of tunnel surrounding rock pressure based on the theory of the progressive damage and method of characteristic curve. Finally, it compares the pressure on the numerical simulative models with on the site date, and it proves that the prediction method has practical engineering value.

Sign in / Sign up

Export Citation Format

Share Document