LOAD-CARRYING CAPACITY AND PRACTICAL DESIGN METHOD OF WELDED HOLLOW SPHERICAL JOINTS IN SPACE LATTICED STRUCTURES

Stone column is often employed for strengthening of an embankment seated on deep soft clay. But in very soft clay having undrained shear strength less than or equal to 15 kPa, stone column may not derive adequate load carrying capacity and undergo large lateral deformation due to inadequate lateral confinement. In such circumstances, reinforcement to individual stone column by geosynthetics enhances load carrying capacity and reduces lateral deformation. This paper addresses parametric study on behaviour of embankment resting on Geosynthetic Reinforced Stone Column (GRSC) considering parameters such as stone column spacing to diameter ratio, deformation modulus of stone column material, geosynthetic stiffness, thickness of soft clay, and height of embankment by 3D numerical analysis. Finally, equation for Settlement Improvement Factor (SIF), defined as ratio between settlement of embankment without treatment and with geosynthetic reinforced stone column, is proposed that correlates with the major influence parameters such as stone column spacing to diameter ratio, deformation modulus of soft clay, and geosynthetic stiffness.

Download Full-text

Strength Calculation and Equal Load-Carrying-Capacity Design of an Undermatched HSLA Lap Joint under Out-of-Plane Bending

Metals ◽

10.3390/met11010161 ◽

2021 ◽

Vol 11 (1) ◽

pp. 161

Author(s):

Junli Guo ◽

Zhibo Dong ◽

Hongyuan Fang ◽

Jiajie Wang

Keyword(s):

Carrying Capacity ◽

Calculation Method ◽

Design Method ◽

Strength Calculation ◽

Weld Strength ◽

Load Carrying Capacity ◽

Lap Joint ◽

Load Carrying ◽

Out Of Plane ◽

Plane Bending

This work aimed to design an undermatched lap joint that has an equal load-carrying capacity (ELCC) with a traditional equalmatched joint under out-of-plane bending. A weld strength calculation method was proposed based on the similarity of a lap joint and a T joint, as shown using linear elastic finite element (FE) analysis, and then applied in the analysis of a lap joint and the design of an ELCC lap joint. A single lap joint of HQ785 steel was chosen for experimental verification. The bending force limit of the ELCC joint was 93.35% of the theoretical prediction and 96.90% of the traditional equalmatched joint. The results show that the weld strength calculation method and the ELCC design method are reasonable and feasible.

Download Full-text

Design method for calculating load-carrying capacity of reinforced concrete beams strengthened with external FRP

Construction and Building Materials ◽

10.1016/j.conbuildmat.2013.10.015 ◽

2014 ◽

Vol 50 ◽

pp. 577-583 ◽

Cited By ~ 18

Author(s):

Tomas Skuturna ◽

Juozas Valivonis

Keyword(s):

Reinforced Concrete ◽

Carrying Capacity ◽

Concrete Beams ◽

Design Method ◽

Reinforced Concrete Beams ◽

Load Carrying Capacity ◽

Load Carrying

Download Full-text

Load Carrying Capacity of Metal Dowel Type Connections of Timber Structures

Civil and Environmental Engineering ◽

10.2478/cee-2014-0011 ◽

2014 ◽

Vol 10 (2) ◽

pp. 51-60

Author(s):

Jozef Gocál

Keyword(s):

Carrying Capacity ◽

Shear Plane ◽

Load Carrying Capacity ◽

Double Shear ◽

Study Results ◽

Load Carrying ◽

Practical Design ◽

Capacity Calculation ◽

Laterally Loaded ◽

Mathematical Relationships

AbstractThis paper deals with the load-carrying capacity calculation of laterally loaded metal dowel type connections according to Eurocode 5. It is based on analytically derived, relatively complicated mathematical relationships, and thus it can be quite laborious for practical use. The aim is to propose a possible simplification of the calculation. Due to quite a great variability of fasteners’ types and the connection arrangements, the attention is paid to the most commonly used nailed connections. There was performed quite an extensive parametric study focused on the calculation of load-carrying capacity of the simple shear and double shear plane nail connections, joining two or three timber parts of softwood or hardwood. Based on the study results, in conclusion there are presented simplifying recommendations for practical design.

Download Full-text

Influence of Yield Strength Variability over Cross-Section to Steel Beam Load-Carrying Capacity

Nonlinear Analysis Modelling and Control ◽

10.15388/na.2005.10.2.15129 ◽

2005 ◽

Vol 10 (2) ◽

pp. 151-160 ◽

Cited By ~ 3

Author(s):

J. Kala ◽

Z. Kala

Keyword(s):

Yield Strength ◽

Cross Section ◽

Carrying Capacity ◽

Bending Moment ◽

Statistical Characteristics ◽

Load Carrying Capacity ◽

Load Carrying ◽

Strength Variability ◽

Hot Rolled ◽

Hot Rolled Steel

Authors of article analysed influence of variability of yield strength over cross-section of hot rolled steel member to its load-carrying capacity. In calculation models, the yield strength is usually taken as constant. But yield strength of a steel hot-rolled beam is generally a random quantity. Not only the whole beam but also its parts have slightly different material characteristics. According to the results of more accurate measurements, the statistical characteristics of the material taken from various cross-section points (e.g. from a web and a flange) are, however, more or less different. This variation is described by one dimensional random field. The load-carrying capacity of the beam IPE300 under bending moment at its ends with the lateral buckling influence included is analysed, nondimensional slenderness according to EC3 is λ¯ = 0.6. For this relatively low slender beam the influence of the yield strength on the load-carrying capacity is large. Also the influence of all the other imperfections as accurately as possible, the load-carrying capacity was determined by geometrically and materially nonlinear solution of very accurate FEM model by the ANSYS programme.

Download Full-text

Fuzzy Sets Theory in Comparison with Stochastic Methods to Analyse Nonlinear Behaviour of a Steel Member under Compression

Nonlinear Analysis Modelling and Control ◽

10.15388/na.2005.10.1.15135 ◽

2005 ◽

Vol 10 (1) ◽

pp. 65-75 ◽

Cited By ~ 5

Author(s):

Z. Kala

Keyword(s):

Fuzzy Sets ◽

Carrying Capacity ◽

Stochastic Methods ◽

Nonlinear Behaviour ◽

Load Carrying Capacity ◽

Load Carrying ◽

Input Parameters ◽

Stochastic Solution ◽

Fuzzy Solution ◽

Sets Theory

The load-carrying capacity of the member with imperfections under axial compression is analysed in the present paper. The study is divided into two parts: (i) in the first one, the input parameters are considered to be random numbers (with distribution of probability functions obtained from experimental results and/or tolerance standard), while (ii) in the other one, the input parameters are considered to be fuzzy numbers (with membership functions). The load-carrying capacity was calculated by geometrical nonlinear solution of a beam by means of the finite element method. In the case (ii), the membership function was determined by applying the fuzzy sets, whereas in the case (i), the distribution probability function of load-carrying capacity was determined. For (i) stochastic solution, the numerical simulation Monte Carlo method was applied, whereas for (ii) fuzzy solution, the method of the so-called α cuts was applied. The design load-carrying capacity was determined according to the EC3 and EN1990 standards. The results of the fuzzy, stochastic and deterministic analyses are compared in the concluding part of the paper.

Download Full-text

Pavement Damage Due to Conventional and New Generation of Wide-Base Super Single Tires

Tire Science and Technology ◽

10.2346/1.2174344 ◽

2005 ◽

Vol 33 (4) ◽

pp. 210-226 ◽

Cited By ~ 6

Author(s):

I. L. Al-Qadi ◽

M. A. Elseifi ◽

P. J. Yoo ◽

I. Janajreh

Keyword(s):

Carrying Capacity ◽

Material Properties ◽

Three Dimensional ◽

Fe Analysis ◽

Load Carrying Capacity ◽

Inflation Pressure ◽

3D Finite Element ◽

Load Carrying ◽

Pavement Damage ◽

New Generation

Abstract The objective of this study was to quantify pavement damage due to a conventional (385/65R22.5) and a new generation of wide-base (445/50R22.5) tires using three-dimensional (3D) finite element (FE) analysis. The investigated new generation of wide-base tires has wider treads and greater load-carrying capacity than the conventional wide-base tire. In addition, the contact patch is less sensitive to loading and is especially designed to operate at 690kPa inflation pressure at 121km/hr speed for full load of 151kN tandem axle. The developed FE models simulated the tread sizes and applicable contact pressure for each tread and utilized laboratory-measured pavement material properties. In addition, the models were calibrated and properly validated using field-measured stresses and strains. Comparison was established between the two wide-base tire types and the dual-tire assembly. Results indicated that the 445/50R22.5 wide-base tire would cause more fatigue damage, approximately the same rutting damage and less surface-initiated top-down cracking than the conventional dual-tire assembly. On the other hand, the conventional 385/65R22.5 wide-base tire, which was introduced more than two decades ago, caused the most damage.

Download Full-text