Large hemispheric differences in the Hadley cell strength variability due to ocean coupling

By modulating the distribution of heat, precipitation and moisture, the Hadley cell holds large climate impacts at low and subtropical latitudes. Here we show that the interannual variability of the annual mean Hadley cell strength is ~ 30% less in the Northern Hemisphere than in the Southern Hemisphere. Using a hierarchy of ocean coupling experiments, we find that the smaller variability in the Northern Hemisphere stems from dynamic ocean coupling, which has opposite effects on the variability of the Hadley cell in the Southern and Northern Hemispheres; it acts to increase the variability in the Southern Hemisphere, which is inversely linked to equatorial upwelling, and reduce the variability in the Northern Hemisphere, which shows a direct relation with the subtropical wind-driven overturning circulation. The important role of ocean coupling in modulating the tropical circulation suggests that further investigation should be carried out to better understand the climate impacts of ocean-atmosphere coupling at low latitudes.

Preliminary Finite Element Analysis and Flight Simulations of a Modular Drone Built through Fused Filament Fabrication

This paper discusses the architecture and preliminary design of an Unmanned Aerial Vehicle (UAV), whose actual operative scenario and required performances drive its flying configuration. The UAV is a multirotor and can be adapted to be used as a tricopter, a quadcopter, a hexacopter, and an octocopter: the number (and consequent arrangement) of the arms modify its performance. Customization is combined with the concept of additive manufacturing, as all components are designed to be produced in Fused Filament Fabrication (FFF). This approach does not limit the application scenarios of the drone; it is instead a further push in the direction of customization, as it permits continuous upgrades over time. The paper simulates four scenarios and discusses how to optimize performances such as payload, thrust-to-weight ratio, efficiency, flight time, and maximum speed through suitable configurations. Avionic components already available on the market integrate into a customizable and adaptable frame. This analysis reveals the most severe conditions for the structure, and conducts a structural validation of its performance. Validating the functional use of FFF-produced parts is challenging due to the anisotropic behavior of the parts. However, some structural elements are thin-walled and enjoy being printed with a 100% linear infill. A simplified approach to those elements has already been proposed and validated through a parallel with UniDirectional Composites, whose 2D testing procedures and methodologies have been derived and adapted. An FEA of some elements of the frame is conducted, using shell elements to discretize the geometry. A proper definition of their mechanical response is possible because the constitutive model is not isotropic a priori but reflects the behavior of the finished parts. The tensile strength variability in the material reference system is high: a component-by-component comparison proves the design to be adequate and measured to the surrounding conditions; however, it highlights the absence of a defined failure criterion.

An approach for modelling spatial variability in permeability of cement-admixed soil

This paper presents a framework for modelling the random variation in permeability in cement-admixed soil based on the binder content variation and thereby relating the coefficient of permeability to the unconfined compressive strength of a cement-admixed clay. The strength–permeability relationship was subsequently implemented in random finite element method (RFEM). The effects of spatial variation in both strength and permeability of cement-admixed clays in RFEM is illustrated using two examples concerning one-dimensional consolidation. Parametric studies considering different coefficient of variation and scale of fluctuation configurations were performed. Results show that spatial variability of the cement-admixed clay considering variable permeability can significantly influence the overall consolidation rate, especially when the soil strength variability is high. However, the overall consolidation rates also depend largely on the prescribed scales of fluctuation; in cases where the variation is horizontally layered, stagnation in pore pressure dissipation may occur due to soft parts yielding.

The Study of Physico-Mechanical Properties of Polylactide Composites with Different Level of Infill Produced by the FDM Method

The aim of this study was to evaluate the changes in physical-mechanical properties of the samples manufactured by 3D printing technology with the addition of varying degrees of polylactide (PLA) infill (50, 70, 85 and 100%). Half of the samples were soaked in physiological saline. The material used for the study was neat PLA, which was examined in terms of hydrolytic degradation, crystallization, mechanical strength, variability of properties at elevated temperatures, and dissipation of mechanical energy depending on the performed treatment. A significant impact of the amount of infill on changeable mechanical properties, such as hydrolytic degradation and crystallization was observed. The FDM printing method allows for waste–free production of light weight unit products with constant specyfic strength.

The Acute Effects of the Atypical Dissociative Hallucinogen Salvinorin A on Functional Connectivity in the Human Brain

Salvinorin A (SA) is a κ-opioid receptor agonist and atypical dissociative hallucinogen found in Salvia divinorum. Despite the resurgence of hallucinogen studies, the effects of κ-opioid agonists on human brain function are not well-understood. This placebo-controlled, within-subject study used functional magnetic resonance imaging for the first time to explore the effects of inhaled SA on strength, variability, and entropy of functional connectivity (static, dynamic, and entropic functional connectivity, respectively, or sFC, dFC, and eFC). SA tended to decrease within-network sFC but increase between-network sFC, with the most prominent effect being attenuation of the default mode network (DMN) during the first half of a 20-min scan (i.e., during peak effects). SA reduced brainwide dFC but increased brainwide eFC, though only the former effect survived multiple comparison corrections. Finally, using connectome-based classification, most models trained on dFC network interactions could accurately classify the first half of SA scans. In contrast, few models trained on within- or between-network sFC and eFC performed above chance. Notably, models trained on within-DMN sFC and eFC performed better than models trained on other network interactions. This pattern of SA effects on human brain function is strikingly similar to that of other hallucinogens, necessitating studies of direct comparisons.