Effects of Rinsing Water Temperature and Preheated Composites on Microleakage of Composite Restorations with Two Bonding Agents

2022 ◽  
Author(s):  
Mohammad Reza Malekipour ◽  
Mehrdad Barekatain ◽  
Farzaneh Shirani ◽  
Samaneh Alaei
Keyword(s):  
Water Temperature ◽  
Composite Resin ◽  
Acid Etching ◽  
Single Bond ◽  
Class V ◽  
Bonding Agents ◽  
Composite Restorations ◽  
Valuable Method ◽  
Group 1

Objectives: The aim of this study was to evaluate the effects of rinsing water temperature and preheated composites on microleakage of class V restorations with two different bonding agents. Materials and Methods: Eighty class V cavities were prepared in the buccal and lingual surfaces of 40 molars. Single Bond and Prime and Bond NT bonding agents were used. The teeth were divided into four groups of 10. G1: After acid etching, cavities were rinsed with 23˚C water and filled with 23˚C composite resin. G2: Rinsing water and composite resin had 55˚C temperature. G3: Rinsing water had 55˚C and composite resin had 23˚C temperature. G4: Rinsing water had 23˚C and composite resin had 55˚C temperature. The specimens were immersed in 0.5% basic fuchsine dye. Microleakage scores were analysed with the Kruskal-Wallis, Mann-Whitney U, and Wilcoxon tests. Results: There were significant differences in microleakage of specimens prepared with Single Bond and Prime and Bond NT only in group 1 (P<0.05). There were no significant differences between the microleakage of groups rinsed with different water temperatures (P>0.05). There were significant differences between the unheated and preheated composite groups (P<0.05). Conclusion: Preheating of composite is a valuable method to increase its adaptability and decrease microleakage of composite restorations.

scholarly journals Influence of Artificial Aging in Marginal Adaptation of Mixed Class V Cavities

2013 ◽  
Vol 14 (2) ◽  
pp. 316-319 ◽  
Author(s):  
Mateus Rodrigues Tonetto ◽  
Marcelo Ferrarezi de Andrade ◽  
Shelon Cristina Souza Pinto ◽  
Alvaro Henrique Borges ◽  
Darlon Martins Lima ◽  
...  
Keyword(s):  
Thermal Cycling ◽  
Artificial Aging ◽  
Composite Resin ◽  
Acid Etching ◽  
Marginal Adaptation ◽  
Single Bond ◽  
Third Molars ◽  
Class V ◽  
Before And After ◽  
Phosphoric Acid Etching

ABSTRACT The aim of this study was to investigate whether the artificial aging by thermal cycling had influenced the marginal adaptation of class V restorations with/without chlorhexidine application in the bond process. Twelve intact human third molars were used. Class V cavity preparations were performed on the buccal surface and the teeth received 35% phosphoric acid-etching procedure (Ultradent Products Inc., South Jordan, Utah, USA). Subsequently, the samples were divided in two groups: Untreated acid-etched dentin and chlorhexidine application as an adjunct in the bond process. The adhesive Single Bond 2 (3M ESPE, St. Paul, MN, USA) was used after 2% chlorhexidine application, and the restorations were performed with FiltekTM Z350 XT (3M ESPE) composite resin. The specimens were submitted to artificial aging by thermal cycling with 3,000 cycles. Analyzes were performed on scanning electron microscopy using replicas of marginal adaptation in percentage of continuous margin before and after the artificial aging. The data were analyzed by paired test and the results showed statistically significant differences in the percentage of continuous margin with/without chlorhexidine treatment before and after thermal cycling. This study concluded that the artificial aging by thermal cycling influenced the marginal adaptation of mixed class V composite restorations. How to cite this article Tonetto MR, Bandéca MC, de Oliveira Barud HG, Pinto SCS, Lima DM, Borges AH, de Campos EA, de Andrade MF. Influence of Artificial Aging in Marginal Adaptation of Mixed Class V Cavities. J Contemp Dent Pract 2013;14(2):316-319.

scholarly journals Interfacial integrity of bonded restorations with self-etching adhesives: Water storage and thermo-mechanical cycling

2012 ◽  
Vol 06 (02) ◽  
pp. 169-177
Author(s):  
Gislaine Cristine Martins ◽  
Alfonso Sánchez-Ayala ◽  
Paulo Henrique Perlatti D’Alpino ◽  
Abraham Lincoln Calixto ◽  
João Carlos Gomes ◽  
...  
Keyword(s):  
Bond Strength ◽  
Water Storage ◽  
Single Bond ◽  
Third Molars ◽  
Class V ◽  
Mean Values ◽  
Composite Restorations ◽  
Mechanical Cycling ◽  
Interfacial Gap ◽  
Made In

ABSTRACTObjectives: Objective: To evaluate the effect of thermo-mechanical cycling (TMC) on the microleakage (μL) and axial gap width (AG) of Class V bonded restorations in premolars using self-etching adhesive systems. The bond strength of composite restorations to dentin (μTBS) using the same adhesives was also evaluated in third molars after water storage: 24 h and 6 months. The research hypotheses were tested for the results of two self-etching adhesives in comparison when a conventional two-step adhesive was used: (1) the μL and AG would be lower, regardless of TMC; (2) the μTBS of self-etching adhesives would be higher, irrespective of evaluation times.Methods: Sixty Class V composite restorations were made in 30 premolars and bonded with Adper Single Bond 2 (ASB2), AdheSE (ASE), and Adper Prompt L-Pop (APL-P) (n=20). Dentin μL and AG were immediately measured for half of the sample. The other half was evaluated after TMC. Eighteen third molars were also selected and bonded using the same adhesives to test the μTBS to dentin. Specimens were evaluated after 24 h and 6 months of water storage.Results: No differences in μL and AG were found among the groups (P>.05). The μTBS mean values were: ASB2>ASE>APL-P (P<.05); only Adper Single Bond 2 presented a significantly lower μTBS after water storage (P<.05)Conclusions: The bonding approach does not influence the microleakage and interfacial gap extension. Despite the decrease in the mean values, the bond strength to dentin of the conventional, two-step adhesive remains high after 6 months of water storage. (Eur J Dent 2012;6:169-177)

scholarly journals Quantitative evaluation of microleakage in class V cavities using one-bottle and self-etching adhesive systems

2004 ◽  
Vol 18 (3) ◽  
pp. 253-259 ◽  
Author(s):  
Fabiana Mantovani Gomes França ◽  
Flávio Henrique Baggio Aguiar ◽  
Alex José Souza dos Santos ◽  
José Roberto Lovadino
Keyword(s):  
Methylene Blue ◽  
In Vitro Study ◽  
Adhesive System ◽  
Acid Etching ◽  
Single Bond ◽  
Adhesive Systems ◽  
Class V ◽  
Bonding System ◽  
Root Dentin

The aim of this in vitro study was to evaluate quantitatively the microleakage in class V cavities restored with one-bottle and self-etching adhesive systems with and without previous acid etching. Two one-bottle adhesive systems (Single Bond and Prime & Bond 2.1) and one self-etching adhesive system (Clearfil Mega Bond) were used in this study. One hundred and twenty sound human premolar teeth were randomly divided into 6 groups, and 20 class V restorations were prepared in the root dentin to test each bonding system. Each bonding system was used with and without acid etching. Specimens were prepared, dyed with 2% methylene blue, sectioned, triturated, and evaluated with an absorbance spectrophotometer test in order to quantify the infiltrated dye. Results were statistically evaluated by ANOVA and Tukey-Kramer test. No statistically significant differences were found among the adhesive systems when no etching agent was used. However, the Single Bond adhesive system showed statistically significant lower microleakage means than Clearfil Mega Bond and Prime & Bond 2.1 when 37% phosphoric acid was used. Single Bond and Clearfil Mega Bond adhesive systems presented similar behavior when the manufacturers' instructions were followed.

scholarly journals Effect of Proteolytic Agents on Microleakage of Etch and Rinse Adhesive Systems

2017 ◽  
Vol 16 ◽  
pp. 1-11
Author(s):  
Shahin Kasraei ◽  
Ebrahim Yarmohammadi ◽  
Maryam Farhadian ◽  
Mona Malek
Keyword(s):  
Phosphoric Acid ◽  
Nd:Yag Laser ◽  
Control Group ◽  
Single Bond ◽  
Adhesive Systems ◽  
Class V ◽  
Dentin Surface ◽  
Composite Restorations ◽  
Etch And Rinse ◽  
Significant Difference

Objective: this study aimed to assess the effect of treatment of phosphoric acid etched dentin surface with 5% bromelain enzyme and Nd:YAG laser prior to the use of etch and rinse adhesive systems on microleakage margins of class V composite restorations. Materials and Methods: sixty sound premolar teeth were selected. Standard class V cavities were prepared in the buccal and lingual surfaces of each teeth. Preparation in that way 1 mm of the cavity was above and 1 mm of it was below the cementoenamel junction. The teeth were then randomly divided into three groups including 20 teeth(40cavities  in each gorup). Two ethanol base etch and rinse system (Adper Single Bond and OptiBond Solo) was applied in each group. In the control group, cavities were etched with 37% phosphoric acid. Adper Single Bond was applied to 20 and OptiBond Solo was applied to the remaining 20 cavities and they were restored with Z250 composite (n=40). The same procedures were performed in bromelain and Nd:YAG laser groups with the difference that prior to the application of adhesive, aqueous 5% bromelain was applied in bromelain group while Nd:YAG laser was irradiated in laser group. All teeth were thermocycled and their apices were sealed with sticky wax. The tooth surfaces were coated with nail varnish except for 1 mm around the restoration margins, and the teeth were then immersed in fuchsine and sectioned by a diamond disc into mesial and distal halves. Marginal microleakage at both sides was determined and scored under a stereomicroscope at x40 magnification. Then data were analyzed using the Kruskal Wallis and Mann Whitney tests (α=0.05). Results: according the result of Mann Whitney test, Cervical margins showed significantly higher microleakage than the occlusal margins (P=0.000) but no significant difference was noted in microleakage of occlusal (P=0.362) or gingival (P=0.147) margins among the three groups by Kruskal Wallis test. Conclusion: in conclusion, application of proteolytic agents(5% bromelain solution and Nd:YAG laser)  on acid-etched dentin surface prior to the application of adhesive has no significant effect on marginal microleakage of class V composite restorations. 

scholarly journals Effect of operator variability on microleakage with different adhesive systems

2013 ◽  
Vol 07 (S 01) ◽  
pp. S060-S065 ◽  
Author(s):  
Emel Karaman ◽  
A. Ruya Yazici ◽  
Burak Aksoy ◽  
Erdem Karabulut ◽  
Gul Ozgunaltay ◽  
...  
Keyword(s):  
Faculty Member ◽  
Clinical Experience ◽  
Undergraduate Student ◽  
Composite Resin ◽  
Research Assistant ◽  
Single Bond ◽  
Basic Fuchsin ◽  
Adhesive Systems ◽  
Adhesive Material ◽  
Class V

ABSTRACTObjective: The objective of this study was to evaluate the effect of operator variability on microleakage with different adhesive systems. Materials and Methods: A total of 180 standardized Class V cavities were prepared on facial and lingual of 90 extracted human premolar teeth and randomly assigned to five groups according to the adhesive systems used (n = 36): Prime and Bond NT (PB), Single Bond (SB), Futura Bond NR, Xeno III (XE) and Adper Prompt-L-Pop (LP). The adhesive groups were then further subdivided into three operator groups according to level of clinical experience (n = 12): An undergraduate student, a research assistant and a faculty member. All cavities were restored with same composite resin. The restored teeth were thermocycled (500 cycles, 5-55°C) then immersed in 0.5% basic fuchsin and measured for leakage under a stereomicroscope. Statistical analyses were performed with the Kruskal-Wallis and Mann-Whitney U tests. Results: Significant inter-operator variation was found in the enamel margins in the XE group with significantly higher microleakage when used by the undergraduate student (p < 0.05). Although no significant differences in microleakage were found between adhesive systems for the research assistant and faculty member (p > 0.05), significant differences were observed between PB and LP, PB and XE, SB and LP and SB and XE in the enamel margins for the undergraduate student (p < 0.05). Conclusions: Microleakage of adhesive systems is more dependent on interactions between the operator and adhesive material than on the choice of adhesive material.

scholarly journals Effect of thermal cycling and filling technique on leakage of composite resin restorations

2004 ◽  
Vol 12 (4) ◽  
pp. 307-311 ◽  
Author(s):  
Silvia Kenshima ◽  
Rosa Helena Miranda Grande ◽  
Julio da Motta Singer ◽  
Rafael Yagüe Ballester
Keyword(s):  
Thermal Cycling ◽  
Silver Nitrate ◽  
Composite Resin ◽  
Composite Resins ◽  
Fluorescent Light ◽  
Single Bond ◽  
Class V ◽  
Composite Resin Restorations ◽  
Nail Varnish

The objective of this study was to evaluate in vitro the effect on leakage of two incremental filling techniques and two composite resins with different elastic modulus and similar polymerization shrinkage. Eighty Class V cavities (4x4x2mm) were prepared in bovine incisors and were randomly restored with Z-250 (Z) or Durafill VS (D) + Single Bond in axial (a) or oblique (o) increments. The restorations were divided into two groups: Not Aged - N (4-hour-storage in water at 37ºC) and Aged - A (1-week storage in water at 37ºC + 1000 x - 5º-55ºC / 1-min dwell time). The specimens were covered with 2 coats of nail varnish so that only the restoration margins were exposed to silver nitrate 50% (2h) and developed under fluorescent light (8h). After they were sectioned twice in buccal-lingual direction, the four exposed surfaces were digitized (Vidcap) and the silver nitrate penetration was measured (ImageLab) at the incisal and gingival walls. Data were analyzed by a 3-way ANOVA (Resin, Filling Technique and Aging) separately for incisal and gingival walls (alpha=0.05). Resin and Aging were statistically significant either for the incisal and the gingival walls. The microfill composite resin infiltrated more than the hybrid composite. The thermal cycling caused an overall increase in silver nitrate penetration. The filling technique affected leakage depending on the composite resin and aging regimen.

scholarly journals Influence of filling technique and bevel preparation on marginal sealing of conventional and low shrinkage composite restorations

2015 ◽  
Vol 2 (6) ◽  
pp. 474
Author(s):  
Pâmella Tomazi Godoy De Oliveira ◽  
Rodrigo Monteiro Vieira ◽  
Patrícia Dos Santos Jardim ◽  
Celso Afonso Klein Júnior ◽  
Ewerton Nochi Conceição ◽  
...  
Keyword(s):  
Level Set ◽  
Composite Resin ◽  
Gap Formation ◽  
Marginal Gap ◽  
Chi Square ◽  
Significance Level ◽  
Composite Restorations ◽  
Group 1 ◽  
Chi Square Tests

AIM: The aim of this study was to evaluate two composite restorations (conventional methacrylate-based and low shrinkage-based silorane), associated or not to beveling and incremental technique, in relation to the microleakage and marginal gap formation tests. MATERIAL AND METHODS: 30 sound human molars had their mesial and distal surfaces prepared with and without bevel. The teeth were divided into six groups according to the type of resin (conventional nanofilled or silorane resin), and restorative filling technique (incremental technique or builk). Microleakage and marginal gap formation data were statistically analyzed by Kruskal-Wallis and Chi-Square tests, with a significance level set at 5%. RESULTS: Group 1 (Z350 XT, without bevel, incremental technique) presented highest rate of microleakage and marginal gap in most of the restorations, with statistically significant differences. Groups 4 and 6 (P90, beveled, builk and P90, beveled and incremental technique) had lower rates of microleakage and absence of marginal gaps in most of the restorations. CONCLUSION: It’s concluded that the silorane showed lower rates of marginal gaps and microleakage, when compared to the conventional methacrylate-based resin. Bevel preparation was effective in reducing microleakage and marginal gaps for both resins used. Incremental technique was not necessary when associated with low shrinkage composite resin.

Microleakage and Shear Bond Strength of Composite Restorations Under Cycling Conditions

2017 ◽  
Vol 42 (2) ◽  
pp. E71-E80 ◽  
Author(s):  
RF Zanatta ◽  
M Lungova ◽  
AB Borges ◽  
CRG Torres ◽  
H-G Sydow ◽  
...  
Keyword(s):  
Bond Strength ◽  
Thermal Cycling ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Control Group ◽  
Strength Testing ◽  
Class V ◽  
Composite Restorations ◽  
Etch And Rinse ◽  
Self Etch

SUMMARY Objectives: The aim of this study was to evaluate microleakage and shear bond strength of composite restorations under different cycling conditions. Methods and Materials: Class V cavities were prepared in the buccal and lingual surfaces of 30 human molars (n=60). A further 60 molars were used to prepare flat enamel and dentin specimens (n=60 each). Cavities and specimens were divided into six groups and pretreated with an adhesive (self-etch/Clearfil SE Bond or etch-and-rinse/Optibond FL). Composite was inserted in the cavities or adhered to the specimens' surfaces, respectively, and submitted to cycling (control: no cycling; thermal cycling: 10,000 cycles, 5°C to 55°C; thermal/erosive cycling: thermal cycling plus storage in hydrochloric acid pH 2.1, 5 minutes, 6×/day, 8 days). Microleakage was quantified by stereomicroscopy in enamel and dentin margins after immersion in silver nitrate. Specimens were submitted to shear bond strength testing. Statistical analysis was done by two-way analysis of variance and Kruskal-Wallis tests (p&lt;0.05). Results: Microleakage in enamel margins was significantly lower in the control group compared with thermal cycling or thermal/erosive cycling. Erosive conditions increased microleakage compared with thermal cycling (significant only for Clearfil SE Bond). No significant differences were observed in dentin margins. Bond strength of enamel specimens was reduced by thermal cycling and thermal/erosive cycling when Clearfil SE Bond was used and only by thermal/erosive cycling when Optibond FL was used. No differences were observed among dentin specimens. Conclusions: Thermal/erosive cycling can adversely affect microleakage and shear bond strength of composite resin bonded to enamel.

scholarly journals Interaction between photoactivators and adhesive systems used as modeling liquid on the degree of conversion of a composite for bleached teeth

2018 ◽  
Vol 21 (3) ◽  
pp. 270
Author(s):  
Thiago Jonathan Silva Dos Santos ◽  
Ana Margarida Dos Santos Melo ◽  
Matheus Dantas Tertulino ◽  
Boniek Castillo Dutra Borges ◽  
Ademir Oliveira Da Silva ◽  
...  
Keyword(s):  
Composite Resin ◽  
Composite Resins ◽  
Degree Of Conversion ◽  
Control Group ◽  
Single Bond ◽  
Adhesive Systems ◽  
Bonding Agents ◽  
Composite Surface ◽  
Light Emitting ◽  
Made In

<p><strong>Objective: </strong>This study analyzed the effect of two light emitting diodes (LEDs) on the degree of conversion (DC) of a composite resin for bleached teeth under the influence of adhesives systems used as modeling liquid. <strong>Material and methods: </strong>A total of 60 samples of IPS Empress Direct resin (Ivoclar, Vivadent) in BL-L shade were made in a single increment and polymerized for 20 seconds. The treatments were: 1) Type of adhesive used as modeling liquid (Adper Single Bond 2; the bond component of Adper Scotchbond Multi-Purpose; or no adhesive systems used as modeling liquid were used in the control group); and 2) Type of LED (Bluephase, polywave; and Coltolux, monowave). The DC, percentage of monomers converted to polymer during polymerization, was were evaluated using Fourier Transform Infrared Spectroscopy (FTIR) with 10 scans and wavenumber related to 1/λ for observation of the peaks at 1608 and 1638 cm<sup>-1</sup>. Data were statistically analyzed by two-way analysis of variance (ANOVA) with Tukey's test (<em>p</em>&lt; 0.05). <strong>Results:</strong> There was no statistical difference between LEDs in comparison to the treatments (<em>p</em>&gt; 0.05). However, there was a statistically significant increase in the DC for the adhesive systems tested in comparison to the control group (<em>p</em>&lt; 0.05), with the highest values for Single Bond 2. <strong>Conclusion:</strong> It is concluded that the use of adhesives as modeling liquid of Empress Direct resin for bleached teeth shade increases the degree of conversion of the composite surface, and that curing with both kinds of LEDs does not interfere in this property.</p><p><strong> </strong></p><p><strong>Keywords</strong></p><p><strong></strong>Composite resins; Dentin-bonding agents; Surface properties.</p>

Sign in / Sign up

Export Citation Format

Share Document