scholarly journals Experimental investigation of biodiesel-n-butanol fuels blends on performance and emissions in a diesel engine

2021 ◽  
Author(s):  
Tomas Mickevicius ◽  
Gvidonas Labeckas ◽  
Stasys Slavinskas
Keyword(s):  
Diesel Engine ◽  
Combustible Mixture ◽  
Nox Emissions ◽  
Test Results ◽  
Fuel Blends ◽  
Particulate Matter Emissions ◽  
Performance And Emissions ◽  
Smoke Opacity ◽  
Liquid Biofuel ◽  
Lower Carbon

The paper presents the experimental test results reflecting the comparative changes in the performance efficiency and emissions of the exhaust of a naturally aspirated, four-stroke, single-cylinder, air-cooled diesel engine due to its transition from neat rapeseed oil biodiesel to fuel blends prepared by mixing in various proportion (by volume) rapeseed methyl ester (B) and butanol (Bu). The lubricity properties of biodiesel-n-butanol fuel blends were studied using HFRR method. In contrast to previous works, the undertaken investigation is performed with a totally renewable, binary liquid biofuel blends. The purpose of the research is to reduce simultaneously the production of NOx emissions and the exhaust smoke with respect to neat biodiesel due to potentially improved homogeneity of combustible mixture and particulate matter emissions benefits suggested by the higher oxygen content (21.62wt%) and the relatively lower carbon-to-hydrogen ratio (4.8) of the normal n-butanol. The tests revealed that the brake specific fuel consumption for the binary biodiesel-n-butanol fuel blends is always higher than that neat biodiesel produces under the same loading conditions. Maximum nitrogen oxide (NOx) emissions were obtained with the engine running on neat biodiesel (2290 ppm). At full (100%) load conditions, the lowest NOx emission was obtained with the engine running on a biofuel BBu20 blend. The lowest level of carbon monoxide emissions (CO) was observed, when engine running with the most butanol-oxygenated biofuel blend BBu20.The highest smoke opacity of the exhaust was obtained when the engine was fuelled with neat biodiesel and at full load.

scholarly journals Study of performance and emissions in diesel engines operating with biodiesel from soybean oil and water emulsions

2021 ◽  
pp. 19-29
Author(s):  
Sofia Orjuela-Abril ◽  
Jhan Piero Rojas-Suárez ◽  
Jorge Eliécer Duarte Forero
Keyword(s):  
Diesel Engine ◽  
Soybean Oil ◽  
Fuel Consumption ◽  
Rotation Speed ◽  
Combustion Process ◽  
Calorific Value ◽  
Nox Emissions ◽  
Performance And Emissions ◽  
Smoke Opacity ◽  
Polluting Emissions

This study evaluates the influence on the combustion process, fuel consumption, and polluting emissions in a diesel engine, which operates with biodiesel from soybean oil and water emulsions with percentages of 4% and 8%. For this study, a stationary diesel engine operating at four different torque conditions and a fixed rotation speed of 3400 rpm is used. Test fuels are diesel, soybean oil biodiesel, and SB4W and SB8W water emulsions. The results indicate that SB4W and SB8W cause a 6% reduction in calorific value and an 18% and 1% increase in viscosity and density. However, the presence of water in biodiesel can help reduce engine BSFC by 8%. The SB4W and SB8W allow a 23% reduction in NOx emissions. With the use of SB4W fuel, a reduction of 16%, 29%, and 14% in CO, HC, and smoke opacity is obtained compared to soybean oil biodiesel. The maximum inclusion of 8% water in soybean oil biodiesel is recommended since a higher percentage can cause the presence of incomplete combustions.

Effect of Biodiesel, JP-8 and Ultra Low Sulfur Diesel Fuel on Autoignition, Combustion, Performance and Emissions in a Single Cylinder Diesel Engine

2010 ◽  
Author(s):  
Chandrasekharan Jayakumar ◽  
Jagdish Nargunde ◽  
Anubhav Sinha ◽  
Walter Bryzik ◽  
Naeim A. Henein ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Properties ◽  
Nox Emissions ◽  
Single Cylinder ◽  
Combustion Performance ◽  
Ultra Low Sulfur Diesel ◽  
Diffusion Controlled ◽  
Performance And Emissions ◽  
Combustion Fraction ◽  
Low Sulfur

Concern about the depletion of petroleum reserves, rising prices of conventional fuels, security of supply and global warming have driven research toward the development of renewable fuels for use in diesel engines. These fuels have different physical and chemical properties that affect the diesel combustion process. This paper compares between the autoignition, combustion, performance and emissions of soybean derived biodiesel, JP-8 and ultra low sulfur diesel (ULSD) in a high speed single-cylinder research diesel engine equipped with a common rail injection system. Tests were conducted at steady state conditions at different injection pressures ranging from 600 bar to 1200 bar. The ‘rate of heat release’ traces are analyzed to determine the effect of fuel properties on the ignition delay, premixed combustion fraction and mixing and diffusion controlled combustion fractions. Biodiesel produced the largest diffusion controlled combustion fraction at all injection pressures compared to ULSD and JP-8. At 600 bar injection pressure, the diffusion controlled combustion fraction for biodiesel was 53% whereas both JP-8 and ULSD produced 39%. In addition, the effect of fuel properties on engine performance, fuel economy, and engine-out emissions is determined. On an average JP-8 produced 3% higher thermal efficiency than ULSD. Special attention is given to the NOx emissions and particulate matter characteristics. On an average biodiesel produced 37% less NOx emissions compared to ULSD and JP-8.

scholarly journals Stability and Emission Characteristics of Diesel-Ethanol-Coconut Methyl Ester Blends for the Diesel Engines

2015 ◽  
Vol 14 (2) ◽  
pp. 1
Author(s):  
Tanti Ardiyati ◽  
Nathaniel P. Dugos ◽  
Susan A. Roces ◽  
Masaaki Suzuki ◽  
Kusnanto Kusnanto
Keyword(s):  
Methyl Ester ◽  
Diesel Engines ◽  
Emission Characteristics ◽  
Test Results ◽  
Fuel Blends ◽  
Fuel Consumption Rate ◽  
Efficient Combustion ◽  
Smoke Opacity ◽  
The Stability ◽  
Blended Fuels

The stability and emission characteristics of diesel-ethanol-coconut methyl ester (CME) blends were studied to determine the most suitable fuel blends to be applied in diesel engines. This is done in order to assess the potential of the blends as a substitute for commercially available diesel fuel used in diesel engine. The stability results of the blends using 100% and 99.5% ethanol purity showed that the fuel blends containing ethanol up to 10% and CME of 5% and greater exhibited high mutual solubility at any temperature range and were resistant to microbial growths after 3 months storage. Engine operations at low speed especially at idle-no load and using a bigger size engine lead to a minimum ignition delay and result in lower fuel consumption rate. The emission test results with the new- blended fuels showed a reduction in CO2 and increasing percentage by volume of CO2 compared to commercially available diesel. The blends could deliver an efficient combustion and could run efficiently since production of the CO2 gases is higher than that of CO. The blends of 80% diesel, 5% ethanol, 10% CME; and 80% diesel, 10% ethanol, 10% CME could reduce the smoke opacity compared to commercially available diesel.

Impact of Diesel-Butanol-Waste Cooking Oil Biodiesel Blends on Stationary Diesel Engine Performance and Emission Characteristics

2020 ◽  
pp. 173-192
Author(s):  
H. Sharon ◽  
Joel Jackson R. ◽  
Prabha C.
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Specific Energy Consumption ◽  
Waste Cooking Oil ◽  
Nox Emission ◽  
Performance And Emission ◽  
Cooking Oil ◽  
Fuel Blends ◽  
Hydrocarbon Emission ◽  
Smoke Opacity

Feed stock cost and NOX emission are the major barriers for commercialization of biodiesel. Waste cooking oil is well identified as one of the cheapest feed stocks for biodiesel production. This chapter reduces NOX emission of waste cooking oil biodiesel. Test fuel blends are prepared by mixing diesel (20 to 50 v/v%), butanol (5 v/v%), and waste cooking oil biodiesel (45 to 75 v/v%). Fuel properties of waste cooking oil biodiesel are enhanced due to addition of diesel and butanol. Brake specific energy consumption of the blends is higher than diesel fuel. Harmful emissions like carbon monoxide, nitrous oxide, and smoke opacity are lower for blends than diesel fuel. Increasing biodiesel concentration in blend also reduces hydrocarbon emission to a significant extent. The obtained results justify the suitability of proposed cheap blends for diesel engine emission reduction.

Characteristics of performance and emissions in high-speed direct injection diesel engine fueled with diethyl ether/diesel fuel blends

Energy ◽  
2012 ◽  
Vol 43 (1) ◽  
pp. 214-224 ◽  
Author(s):  
Dimitrios C. Rakopoulos ◽  
Constantine D. Rakopoulos ◽  
Evangelos G. Giakoumis ◽  
Athanasios M. Dimaratos
Keyword(s):  
Diesel Engine ◽  
Diethyl Ether ◽  
Diesel Fuel ◽  
High Speed ◽  
Direct Injection ◽  
Direct Injection Diesel Engine ◽  
Fuel Blends ◽  
Performance And Emissions

scholarly journals Influence of Silica Nano-Additives on Performance and Emission Characteristics of Soybean Biodiesel Fuelled Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1489
Author(s):  
R. S. Gavhane ◽  
A. M. Kate ◽  
Manzoore Elahi M. Soudagar ◽  
V. D. Wakchaure ◽  
Sagar Balgude ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Emission Characteristics ◽  
X Ray Diffraction ◽  
Brake Thermal Efficiency ◽  
X Ray ◽  
Performance And Emission ◽  
Fuel Blends ◽  
Soybean Biodiesel ◽  
Performance And Emissions ◽  
Nano Additives

The present study examines the effect of silicon dioxide (SiO2) nano-additives on the performance and emission characteristics of a diesel engine fuelled with soybean biodiesel. Soybean biofuel was prepared using the transesterification process. The morphology of nano-additives was studied using scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDS). The Ultrasonication process was used for the homogeneous blending of nano-additives with biodiesel, while surfactant was used for the stabilisation of nano-additives. The physicochemical properties of pure and blended fuel samples were measured as per ASTM standards. The performance and emissions characteristics of different fuel samples were measured at different loading conditions. It was found that the brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) increased by 3.48–6.39% and 5.81–9.88%, respectively, with the addition of SiO2 nano-additives. The carbon monoxide (CO), hydrocarbon (HC) and smoke emissions for nano-additive added blends were decreased by 1.9–17.5%, 20.56–27.5% and 10.16–23.54% compared to SBME25 fuel blends.

Impact of Using Biodiesels of Different Origin and Additives on the Performance of a Stationary Diesel Engine

2000 ◽  
Vol 122 (4) ◽  
pp. 624-631 ◽  
Author(s):  
A. Serdari ◽  
K. Fragioudakis ◽  
S. Kalligeros ◽  
S. Stournas ◽  
E. Lois
Keyword(s):  
Diesel Engine ◽  
Fatty Acid Methyl Esters ◽  
Corn Oil ◽  
Methyl Esters ◽  
Raw Material ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Fuel Blends ◽  
Different Types ◽  
Particulate Matter Emissions

With the exception of rape seed oil which is the principal raw material for biodiesel Fatty Acid Methyl Esters, (FAME) production, sunflower oil, corn oil, and olive oil, which are abundant in Southern Europe, along with some wastes, such as used frying oils, appear to be attractive candidates for biodiesel production. In this paper fuel consumption and exhaust emission measurements from a single cylinder, stationary diesel engine are described. The engine was fueled with fuel blends containing four different types of biodiesel, at proportions up to 100 percent; the further impact of the usage of two specific additives was also investigated. The four types of biodiesel appeared to have equal performance and irrespective of the raw material used for their production, their addition to the traditional diesel fuel improved the particulate matter emissions. The results improve further when specific additive combinations are used. [S0742-4795(00)00604-9]

Sign in / Sign up

Export Citation Format

Share Document