scholarly journals Mn-doped CaBi4Ti4O15/Pb(Zr,Ti)O3 Ultrasonic Transducers for Continuous Monitoring at Elevated Temperatures

2017 ◽  
Author(s):  
Makiko Kobayashi ◽  
Taiga Kibe ◽  
Hajime Nagata
Keyword(s):  
High Temperature ◽  
Thermal Cycle ◽  
Elevated Temperatures ◽  
Signal To Noise Ratio ◽  
Ultrasonic Transducer ◽  
Sol Gel ◽  
Ultrasonic Transducers ◽  
In Situ Monitoring ◽  
Signal To Noise ◽  
Noise Ratio

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

scholarly journals CMUT-Based Sensor for Acoustic Emission Application: Experimental and Theoretical Contributions to Sensitivity Optimization

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 2042
Author(s):  
Redha Boubenia ◽  
Patrice Le Moal ◽  
Gilles Bourbon ◽  
Emmanuel Ramasso ◽  
Eric Joseph
Keyword(s):  
Signal Processing ◽  
Signal To Noise Ratio ◽  
Ultrasonic Transducer ◽  
Operating Conditions ◽  
Geometrical Parameters ◽  
Signal To Noise ◽  
Coupling Conditions ◽  
Sensor Structure ◽  
Noise Ratio ◽  
Electrical Connections

The paper deals with a capacitive micromachined ultrasonic transducer (CMUT)-based sensor dedicated to the detection of acoustic emissions from damaged structures. This work aims to explore different ways to improve the signal-to-noise ratio and the sensitivity of such sensors focusing on the design and packaging of the sensor, electrical connections, signal processing, coupling conditions, design of the elementary cells and operating conditions. In the first part, the CMUT-R100 sensor prototype is presented and electromechanically characterized. It is mainly composed of a CMUT-chip manufactured using the MUMPS process, including 40 circular 100 µm radius cells and covering a frequency band from 310 kHz to 420 kHz, and work on the packaging, electrical connections and signal processing allowed the signal-to-noise ratio to be increased from 17 dB to 37 dB. In the second part, the sensitivity of the sensor is studied by considering two contributions: the acoustic-mechanical one is dependent on the coupling conditions of the layered sensor structure and the mechanical-electrical one is dependent on the conversion of the mechanical vibration to electrical charges. The acoustic-mechanical sensitivity is experimentally and numerically addressed highlighting the care to be taken in implementation of the silicon chip in the brass housing. Insertion losses of about 50% are experimentally observed on an acoustic test between unpackaged and packaged silicon chip configurations. The mechanical-electrical sensitivity is analytically described leading to a closed-form amplitude of the detected signal under dynamic excitation. Thus, the influence of geometrical parameters, material properties and operating conditions on sensitivity enhancement is clearly established: such as smaller electrostatic air gap, and larger thickness, Young’s modulus and DC bias voltage.

Signal-to-Noise Ratio Enhancement by Accumulation of Signal and Noise along the Spectrum

2021 ◽  
Author(s):  
Igor Lebedev ◽  
Elena Dmitriyeva ◽  
Ekaterina Bondar ◽  
Sayora Ibraimova ◽  
Anastasiya Fedosimova ◽  
...  
Keyword(s):  
Crystalline Structure ◽  
Glass Substrate ◽  
Tin Dioxide ◽  
Signal To Noise Ratio ◽  
Sol Gel ◽  
Amorphous State ◽  
Negative Influence ◽  
Signal To Noise ◽  
Background Removal ◽  
Noise Ratio

This work presents a method for background removal and signal-to-noise ratio enhancement by an accumulation of signal and noise along analyzed spectrum. In this case, the signals are accumulated, and noise, due to its chaotic nature, is suppressed. The method is applied to analyze spectra obtained on DRON-6 diffractometer for study of the crystal structure of thin tin dioxide films produced by sol–gel technology and deposited on a glass substrate. The standard analysis of the crystallographic planes of the samples under study is practically impossible due to the high noise level and the negative influence of the background from the glass substrate. The proposed method transformed the initial spectrum, which cannot be analyzed, into an informative spectrum: the background signal from the substrate is correctly subtracted and the noise decreases by 10 times. To check for possible signal distortion due to accumulation signal along the spectrum, an analysis of simulated spectra was carried out. The onset of the transition of an amorphous state to a crystalline structure of SnO2 is investigated. The crystalline structure of SnO2 thin films depending on the annealing temperature is studied.

Determination of the Best Emulsion for the Microscopy of Crystals

1981 ◽  
Vol 39 ◽  
pp. 32-33
Author(s):  
David A. Grano ◽  
Kenneth H. Downing
Keyword(s):  
Spatial Frequency ◽  
Information Transfer ◽  
Signal To Noise Ratio ◽  
Experimental Situation ◽  
Photographic Emulsion ◽  
Modulation Transfer ◽  
Signal To Noise ◽  
Frequency Space ◽  
Noise Ratio

The retrieval of high-resolution information from images of biological crystals depends, in part, on the use of the correct photographic emulsion. We have been investigating the information transfer properties of twelve emulsions with a view toward 1) characterizing the emulsions by a few, measurable quantities, and 2) identifying the “best” emulsion of those we have studied for use in any given experimental situation. Because our interests lie in the examination of crystalline specimens, we've chosen to evaluate an emulsion's signal-to-noise ratio (SNR) as a function of spatial frequency and use this as our critereon for determining the best emulsion.The signal-to-noise ratio in frequency space depends on several factors. First, the signal depends on the speed of the emulsion and its modulation transfer function (MTF). By procedures outlined in, MTF's have been found for all the emulsions tested and can be fit by an analytic expression 1/(1+(S/S0)2). Figure 1 shows the experimental data and fitted curve for an emulsion with a better than average MTF. A single parameter, the spatial frequency at which the transfer falls to 50% (S0), characterizes this curve.

Experiments in Bright-Field Imaging with Hollow-Cone Illumination

1981 ◽  
Vol 39 ◽  
pp. 226-227
Author(s):  
W. Kunath ◽  
K. Weiss ◽  
E. Zeitler
Keyword(s):  
Signal To Noise Ratio ◽  
Carbon Support ◽  
Electronic System ◽  
Optic Axis ◽  
Hollow Cone ◽  
Signal To Noise ◽  
Bright Field ◽  
Noise Ratio ◽  
Single Field ◽  
Field Imaging

Bright-field images taken with axial illumination show spurious high contrast patterns which obscure details smaller than 15 ° Hollow-cone illumination (HCI), however, reduces this disturbing granulation by statistical superposition and thus improves the signal-to-noise ratio. In this presentation we report on experiments aimed at selecting the proper amount of tilt and defocus for improvement of the signal-to-noise ratio by means of direct observation of the electron images on a TV monitor.Hollow-cone illumination is implemented in our microscope (single field condenser objective, Cs = .5 mm) by an electronic system which rotates the tilted beam about the optic axis. At low rates of revolution (one turn per second or so) a circular motion of the usual granulation in the image of a carbon support film can be observed on the TV monitor. The size of the granular structures and the radius of their orbits depend on both the conical tilt and defocus.

Information capacity and bandwidth limitations in the SEM

1989 ◽  
Vol 47 ◽  
pp. 84-85
Author(s):  
D. C. Joy ◽  
R. D. Bunn
Keyword(s):  
Signal To Noise Ratio ◽  
Critical Dimension ◽  
Information Capacity ◽  
Acquisition Time ◽  
Signal To Noise ◽  
Sem Image ◽  
Probe Size ◽  
Minimum Number ◽  
Noise Ratio ◽  
Signal Channel

The information available from an SEM image is limited both by the inherent signal to noise ratio that characterizes the image and as a result of the transformations that it may undergo as it is passed through the amplifying circuits of the instrument. In applications such as Critical Dimension Metrology it is necessary to be able to quantify these limitations in order to be able to assess the likely precision of any measurement made with the microscope.The information capacity of an SEM signal, defined as the minimum number of bits needed to encode the output signal, depends on the signal to noise ratio of the image - which in turn depends on the probe size and source brightness and acquisition time per pixel - and on the efficiency of the specimen in producing the signal that is being observed. A detailed analysis of the secondary electron case shows that the information capacity C (bits/pixel) of the SEM signal channel could be written as :

Sign in / Sign up

Export Citation Format

Share Document