scholarly journals A Two-Fluid Model for High Viscosity Upward Annular Flow in Vertical Pipes

2021 ◽  
Author(s):  
Joseph X. F. Ribeiro ◽  
Ruiquan Liao ◽  
Aliyu M. Aliyu ◽  
Salem K. B. Ahmed ◽  
Yahaya D. Baba ◽  
...  
Keyword(s):  
Fluid Model ◽  
Accurate Determination ◽  
Flow Characteristics ◽  
High Viscosity ◽  
Two Phase ◽  
Friction Factors ◽  
Two Fluid Model ◽  
Two Fluid ◽  
Selection Of

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

scholarly journals A Two-Fluid Model for High-Viscosity Upward Annular Flow in Vertical Pipes

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3485
Author(s):  
Joseph X. F. Ribeiro ◽  
Ruiquan Liao ◽  
Aliyu M. Aliyu ◽  
Salem K. B. Ahmed ◽  
Yahaya D. Baba ◽  
...  
Keyword(s):  
Pressure Gradient ◽  
Friction Factor ◽  
Fluid Model ◽  
Flow Characteristics ◽  
Interfacial Friction ◽  
Internal Diameter ◽  
Liquid Viscosity ◽  
Two Phase ◽  
Two Fluid Model ◽  
Two Fluid

Proper selection and application of interfacial friction factor correlations has a significant impact on prediction of key flow characteristics in gas–liquid two-phase flows. In this study, experimental investigation of gas–liquid flow in a vertical pipeline with internal diameter of 0.060 m is presented. Air and oil (with viscosities ranging from 100–200 mPa s) were used as gas and liquid phases, respectively. Superficial velocities of air ranging from 22.37 to 59.06 m/s and oil ranging from 0.05 to 0.16 m/s were used as a test matrix during the experimental campaign. The influence of estimates obtained from nine interfacial friction factor models on the accuracy of predicting pressure gradient, film thickness and gas void fraction was investigated by utilising a two-fluid model. Results obtained indicate that at liquid viscosity of 100 mPa s, the interfacial friction factor correlation proposed by Belt et al. (2009) performed best for pressure gradient prediction while the Moeck (1970) correlation provided the best prediction of pressure gradient at the liquid viscosity of 200 mPa s. In general, these results indicate that the two-fluid model can accurately predict the flow characteristics for liquid viscosities used in this study when appropriate interfacial friction factor correlations are implemented.

scholarly journals Natural modes of the two-fluid model of two-phase flow

2021 ◽  
Vol 33 (3) ◽  
pp. 033324
Author(s):  
Alejandro Clausse ◽  
Martín López de Bertodano
Keyword(s):  
Two Phase Flow ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Phase ◽  
Natural Modes ◽  
Two Fluid Model ◽  
Two Fluid

Two-Phase Flows in Mini-/Micro-Gas Flow Channels of PEM Fuel Cells

2013 ◽  
Author(s):  
Sung Chan Cho ◽  
Yun Wang
Keyword(s):  
Pressure Drop ◽  
Gas Flow ◽  
Fluid Model ◽  
Pem Fuel Cells ◽  
Two Phase ◽  
Micro Gas Flow ◽  
Two Fluid Model ◽  
The Impact ◽  
Two Fluid ◽  
Phase Pressure

In this paper, two-phase flow dynamics in a micro channel with various wall conditions are both experimentally and theoretically investigated. Annulus, wavy and slug flow patterns are observed and location of liquid phase on different wall condition is visualized. The impact of flow structure on two-phase pressure drop is explained. Two-phase pressure drop is compared to a two-fluid model with relative permeability correlation. Optimization of correlation is conducted for each experimental case and theoretical solution for the flows in a circular channel is developed for annulus flow pattern showing a good match with experimental data in homogeneous channel case.

A Physically Based, One-Dimensional Two-Fluid Model for Direct Contact Condensation of Steam Jets Submerged in Subcooled Water

2015 ◽  
Vol 1 (2) ◽  
Author(s):  
David Heinze ◽  
Thomas Schulenberg ◽  
Lars Behnke
Keyword(s):  
Direct Contact ◽  
Two Phase Flow ◽  
Fluid Model ◽  
Interfacial Area ◽  
Phase Flow ◽  
Two Phase ◽  
One Dimensional ◽  
Two Fluid Model ◽  
Contact Condensation ◽  
Two Fluid

A simulation model for the direct contact condensation of steam in subcooled water is presented that allows determination of major parameters of the process, such as the jet penetration length. Entrainment of water by the steam jet is modeled based on the Kelvin–Helmholtz and Rayleigh–Taylor instability theories. Primary atomization due to acceleration of interfacial waves and secondary atomization due to aerodynamic forces account for the initial size of entrained droplets. The resulting steam-water two-phase flow is simulated based on a one-dimensional two-fluid model. An interfacial area transport equation is used to track changes of the interfacial area density due to droplet entrainment and steam condensation. Interfacial heat and mass transfer rates during condensation are calculated using the two-resistance model. The resulting two-phase flow equations constitute a system of ordinary differential equations, which is solved by means of the explicit Runge–Kutta–Fehlberg algorithm. The simulation results are in good qualitative agreement with published experimental data over a wide range of pool temperatures and mass flow rates.

Numerical Simulation of Boiling Two-Phase Flow in Tight-Lattice Rod Bundle by 3-Dimensional Two-Fluid Model Code ACE-3D

2008 ◽  
Author(s):  
Hiroyuki Yoshida ◽  
Takeharu Misawa ◽  
Kazuyuki Takase
Keyword(s):  
Void Fraction ◽  
Lift Force ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Phase ◽  
Rod Bundle ◽  
Fraction Distribution ◽  
Two Fluid Model ◽  
Tight Lattice ◽  
Two Fluid

Two-fluid model can simulate two phase flow less computational cost than inter-face tracking method and particle interaction method. Therefore, two-fluid model is useful for thermal hydraulic analysis in large-scale domain such as a rod bundle. Japan Atomic Energy Agency (JAEA) develops three dimensional two-fluid model analysis code ACE-3D, which adopts boundary fitted coordinate system in order to simulate complex shape channel flow. In this paper, boiling two-phase flow analysis in a tight lattice rod bundle is performed by ACE-3D code. The parallel computation using 126CPUs is applied to this analysis. In the results, the void fraction, which distributes in outermost region of rod bundle, is lower than that in center region of rod bundle. At height z = 0.5 m, void fraction in the gap region is higher in comparison with that in center region of the subchannel. However, at height of z = 1.1m, higher void fraction distribution exists in center region of the subchannel in comparison with the gap region. The tendency of void fraction to concentrate in the gap region at vicinity of boiling starting point, and to move into subchannel as water goes through rod bundle, is qualitatively agreement with the measurement results by neutron radiography. To evaluate effects of two-phase flow model used in ACE-3D code, numerical simulation of boiling two-phase in tight lattice rod bundle with no lift force model (neglecting lift force acting on bubbles) is also performed. From the comparison of numerical results, it is concluded that the effects of lift force model are not so large on overall void fraction distribution in tight lattice rod bundle. However, higher void fraction distribution in center region of the subchannel was not observed in this simulation. It is concluded that the lift force model is important for local void fraction distribution in rod bundles.

Prediction of Parameters Distribution of Upward Boiling Two-Phase Flow With Two-Fluid Models

2002 ◽  
Author(s):  
Wei Yao ◽  
Christophe Morel
Keyword(s):  
Void Fraction ◽  
Fluid Model ◽  
Constitutive Relations ◽  
Turbulent Dispersion ◽  
Dispersion Force ◽  
Liquid Temperature ◽  
Two Phase ◽  
Radial Profiles ◽  
Two Fluid Model ◽  
Two Fluid

In this paper, a multidimensional two-fluid model with additional turbulence k–ε equations is used to predict the two-phase parameters distribution in freon R12 boiling flow. The 3D module of the CATHARE code is used for numerical calculation. The DEBORA experiment has been chosen to evaluate our models. The radial profiles of the outlet parameters were measured by means of an optical probe. The comparison of the radial profiles of void fraction, liquid temperature, gas velocity and volumetric interfacial area at the end of the heated section shows that the multidimensional two-fluid model with proper constitutive relations can yield reasonably predicted results in boiling conditions. Sensitivity tests show that the turbulent dispersion force, which involves the void fraction gradient, plays an important role in determining the void fraction distribution; and the turbulence eddy viscosity is a significant factor to influence the liquid temperature distribution.

An Upwind Numerical Method for a Hyperbolic One-Dimensional Two-Fluid Model

2011 ◽  
Author(s):  
Youn-Gyu Jung ◽  
Moon-Sun Chung ◽  
Sung-Jae Yi
Keyword(s):  
Numerical Method ◽  
Fluid Model ◽  
Equation System ◽  
Benchmark Problems ◽  
Two Phase ◽  
One Dimensional ◽  
Flow Problems ◽  
Complete Set ◽  
Two Fluid Model ◽  
Two Fluid

This study discusses on the implementation of an upwind method for a one-dimensional two-fluid model including the surface tension effect in the momentum equations. This model consists of a complete set of six equations including two-mass, two-momentum, and two-internal energy conservation equations having all real eigenvalues. Based on this equation system with upwind numerical method, the present authors first make a pilot code and then solve some benchmark problems to verify whether this model and numerical method is able to properly solve some fundamental one-dimensional two-phase flow problems or not.

Sign in / Sign up

Export Citation Format

Share Document