Effect of Grit Blasting and Polishing Pretreatments on the Microhardness, Adhesion and Corrosion Properties of Electrodeposited Ni-W/SiC Nanocomposite Coatings on 45 Steel Substrate

In this study, grit blasting pretreatment was used to improve the adhesion and corrosion resistance and microhardness of Ni-W/SiC nanocomposite coatings fabricated using conventional electrodeposition technique. Prior to deposition, grit blasting and polishing (more commonly used) pretreatment were used to prepare the surface of the substrate and the 3D morphology of the pretreated substrates was characterized using laser scanning confocal microscopy. The coatings surface and the cross section morphology were analyzed using scanning electron microscopy (SEM). The chemical composition, crystalline structure, microhardness, adhesion, and the corrosion behavior of the deposited coatings were characterized using energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester, scratch tester and electrochemical workstation, respectively. The results indicated that the grit blasting and SiC addition, improved the microhardness, adhesion and corrosion resistance. The Ni-W-SiC nanocomposites pretreated by grit blasting exhibited the best adhesion strength, up to 36.5 ± 0.75 N. Its hardness was the highest and increased up to 673 ± 5.47Hv and its corrosion resistance was the highest compared to the one pretreated by polishing.

Download Full-text

Effect of Grit Blasting and Polishing Pretreatments on the Microhardness, Adhesion and Corrosion Properties of Electrodeposited Ni-W/SiC Nanocomposite Coatings on 45 Steel Substrate

Crystals ◽

10.3390/cryst11070729 ◽

2021 ◽

Vol 11 (7) ◽

pp. 729

Author(s):

Bertrand Vigninou Gbenontin ◽

Min Kang ◽

Ndumia Joseph Ndiithi ◽

Samuel Mbugua Nyambura ◽

Emmanuel Awuah ◽

...

Keyword(s):

Corrosion Resistance ◽

Laser Scanning ◽

Steel Substrate ◽

Laser Scanning Confocal Microscopy ◽

Nanocomposite Coatings ◽

X Ray Diffraction ◽

Corrosion Properties ◽

Grit Blasting ◽

Scanning Confocal Microscopy ◽

The One

In this study, a grit-blasting pretreatment was used to improve the adhesion, corrosion resistance and microhardness of Ni-W/SiC nanocomposite coatings fabricated using the conventional electrodeposition technique. Prior to deposition, grit blasting and polishing (more commonly used) pretreatments were used to prepare the surface of the substrate and the 3D morphology of the pretreated substrates was characterized using laser scanning confocal microscopy. The coating surface and the cross-section morphology were analyzed using scanning electron microscopy (SEM). The chemical composition, crystalline structure, microhardness, adhesion and corrosion behavior of the deposited coatings were characterized using energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), a microhardness tester, a scratch tester and an electrochemical workstation, respectively. The results indicated that the grit blasting and SiC addition improved the microhardness, adhesion and corrosion resistance. The Ni-W/SiC nanocomposites pretreated by grit blasting exhibited the best adhesion strength, up to 36.5 ± 0.75 N. Its hardness was the highest and increased up to 673 ± 5.47 Hv and its corrosion resistance was the highest compared to the one pretreated by polishing.

Download Full-text

Effects of Laser Scanning Speed on Microstructure, Microhardness, and Corrosion Behavior of Laser Cladding Ni45 Coatings

Journal of Chemistry ◽

10.1155/2020/1438473 ◽

2020 ◽

Vol 2020 ◽

pp. 1-11 ◽

Cited By ~ 8

Author(s):

Yanxin Qiao ◽

Jie Huang ◽

Ding Huang ◽

Jian Chen ◽

Wen Liu ◽

...

Keyword(s):

Corrosion Resistance ◽

Corrosion Behavior ◽

Laser Scanning ◽

Scanning Speed ◽

Primary Phase ◽

X Ray Diffraction ◽

X Ray ◽

Microhardness Distribution ◽

Laser Scanning Speed ◽

The One

The effects of laser scanning speed on the microstructure, microhardness, and corrosion behavior of Ni45 coatings were investigated by using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), microhardness, and electrochemical measurements. The results showed that increasing laser scanning speed promotes the transformation from planar crystals to dendrites and refines the grains concurrently. The γ-(Ni, Fe), FeNi3, and M23(C,B)6 are identified as the primary phase composition in the Ni45 coatings regardless of the laser scanning speed. Thereinto, the formation and growth of M23(C,B)6 precipitates can be inhibited with increasing laser scanning speed due to the higher cooling rate, which affects the microhardness distribution and corrosion resistance of the coating. On the one hand, the microhardness of the whole coating presents a downtrend with increasing laser scanning speed due to the reduction of M23(C,B)6 phase. On the other hand, the corrosion resistance in 0.5 M NaCl solution is improved to some extent at higher laser scanning speed because the less precipitation of M23(C,B)6 reduces the depletion of Cr around the precipitates. In contrast, all the coatings exhibit undifferentiated but poor corrosion resistance in the highly corrosive 0.5 M NaCl + 0.5 M H2SO4 solution.

Download Full-text

Influence of Element Penetration Region on Adhesion and Corrosion Performance of Ni-Base Coatings

Coatings ◽

10.3390/coatings10090895 ◽

2020 ◽

Vol 10 (9) ◽

pp. 895

Author(s):

Xiuqing Fu ◽

Zhenyu Shen ◽

Xinxin Chen ◽

Jinran Lin ◽

Hongbing Cao

Keyword(s):

Corrosion Resistance ◽

Laser Scanning ◽

Adhesion Force ◽

Electrochemical Corrosion ◽

Corrosion Current ◽

Scratch Test ◽

Laser Scanning Confocal Microscopy ◽

Scanning Confocal Microscopy ◽

Steel Substrates ◽

Sic Coatings

In this study, Ni–P/Ni–P–SiC coatings were prepared on pretreated 45 steel substrates by scanning electrodeposition. Prior to the electrodeposition, the substrates were subjected to two types of pretreatments: polishing and sandblasting. The 3D morphology of the pretreated substrates was characterized by laser scanning confocal microscopy. The micromorphology and section morphology of the coating surface were characterized by field emission scanning electron microscopy. The section element composition was characterized using an EDS energy spectrum analyzer. The adhesion and corrosion resistance of 15 coatings were analyzed using an automatic scratch tester and CS350 electrochemical workstation. The results showed the presence of an element penetration region between the coating and the substrate. The sandblasting pretreatment and SiC nanoparticle addition helped widen the penetration region of the elements. The Ni–P–SiC coating prepared by scanning electrodeposition on the sandblasted substrate exhibited the thickest penetration region, up to 28.39 µm. A scratch test conducted on this coating showed that it exhibits the best adhesion force, up to 36.5 N. In electrochemical corrosion experiments, its corrosion potential was found to be the highest, reaching −0.30 V, and the corrosion current density was the lowest, reaching 8.45 × 10−7 A·cm−2. The presence of the element penetration region increased the coating adhesion and improved the corrosion resistance.

Download Full-text

In-Situ Observation of Martensite Transformation of Low Carbon High Alloy Steel Using High Temperature Laser Scanning Confocal Microscopy and X-ray Diffraction by Synchrotron Radiation

Tetsu-to-Hagane ◽

10.2355/tetsutohagane.96.64 ◽

2010 ◽

Vol 96 (2) ◽

pp. 64-69 ◽

Cited By ~ 4

Author(s):

Shuoyuan Zhang ◽

Hidenori Terasaki ◽

Yu-ichi Komizo

Keyword(s):

Laser Scanning ◽

Laser Scanning Confocal Microscopy ◽

In Situ Observation ◽

Low Carbon ◽

X Ray Diffraction ◽

High Alloy ◽

High Alloy Steel ◽

X Ray ◽

Scanning Confocal Microscopy

Download Full-text

The Effect of Zn and Zn–WO3 Composites Nano-Coatings Deposition on Hardness and Corrosion Resistance in Steel Substrate

Materials ◽

10.3390/ma14092253 ◽

2021 ◽

Vol 14 (9) ◽

pp. 2253

Author(s):

Channagiri Mohankumar Praveen Kumar ◽

Manjunath Patel Gowdru Chandrashekarappa ◽

Raviraj Mahabaleshwar Kulkarni ◽

Danil Yurievich Pimenov ◽

Khaled Giasin

Keyword(s):

Electron Microscopy ◽

Corrosion Resistance ◽

Tungsten Trioxide ◽

Steel Substrate ◽

Composite Coatings ◽

Nanocomposite Coatings ◽

X Ray Diffraction ◽

Electrodeposition Technique ◽

X Ray ◽

Scanning Electron

Pure Zn (Zinc) and its Zn–WO3 (Zinc–Tungsten trioxide) composite coatings were deposited on mild steel specimens by applying the electrodeposition technique. Zn–WO3 composites were prepared for the concentration of 0.5 and 1.0 g/L of particles. The influence of WO3 particles on Zn deposition, the surface morphology of composite, and texture co-efficient were analyzed using a variety of techniques, such as X-ray diffraction (XRD) and scanning electron microscopy (SEM) with Energy Dispersive X-ray analysis (EDX). Higher corrosion resistance and microhardness were observed on the Zn–WO3 composite (concentration of 1.0 g/L). The higher corrosion resistance and microhardness of 1.0 g/L Zn–WO3 nanocomposite coatings effectively protect the steel used for the manufacture of products, parts, or systems from chemical or electrochemical deterioration in industrial and marine ambient environments.

Download Full-text

Fabrication of Ni–Co–BN (h) Nanocomposite Coatings with Jet Electrodeposition in Different Pulse Parameters

Coatings ◽

10.3390/coatings9010050 ◽

2019 ◽

Vol 9 (1) ◽

pp. 50 ◽

Cited By ~ 1

Author(s):

Hengzheng Li ◽

Min Kang ◽

Yin Zhang ◽

Yuntong Liu ◽

Meifu Jin ◽

...

Keyword(s):

Corrosion Resistance ◽

Duty Cycle ◽

Laser Scanning ◽

Corrosion Current ◽

Pulse Frequency ◽

Laser Scanning Confocal Microscopy ◽

Nanocomposite Coatings ◽

Obvious Effect ◽

Pulse Parameters ◽

Jet Electrodeposition

In order to study the effects of pulse parameters on jet electrodeposition, Ni–Co–BN (h) nanocomposite coatings were prepared on the surface of steel C1045. The samples were analyzed and characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), laser scanning confocal microscopy (LSCM), microhardness tester, and electrochemical workstation. The experimental results showed that the contents of Co and BN (h) nanoparticles in the coatings changed with the variation of pulse parameters. When the pulse frequency was 4 kHz and the duty cycle was 0.7, their contents reached maxima of 27.34 wt % and 3.82 wt %, respectively. The XRD patterns of the coatings showed that the deposits had a face-centered cube (fcc) structure, and there was an obvious preferred orientation in (111) plane. With the increase in pulse parameters, the surface roughness of the coatings first decreased and then increased, with the minimum value obtained being 0.664 µm. The microhardness of the coatings first increased and then decreased with increase in pulse parameters. The maximum value of the microhardness reached 719.2 HV0.05 when the pulse frequency was 4 kHz and the duty cycle was 0.7. In the electrochemical test, the potentiodynamic polarization curves of the coatings after immersion in 3.5 wt % NaCl solution showed the pulse parameters had an obvious effect on the corrosion resistance of the Ni–Co–BN (h) nanocamposite coatings. The corrosion current density and polarization resistance indicated that the coatings had better corrosion resistance when the pulse frequency was 4 kHz and duty cycle was 0.7.

Download Full-text

Laser Scanning Confocal Microscopy and Three-Dimesnsional Reconstruction of the Mitotic Spindles of Unequally Dividing Embryonic Cells

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100158376 ◽

1990 ◽

Vol 48 (3) ◽

pp. 166-167

Author(s):

J. Holy ◽

G. Schatten

Keyword(s):

Confocal Microscopy ◽

Mitotic Spindle ◽

Laser Scanning ◽

Three Dimensional ◽

Laser Scanning Confocal Microscopy ◽

Two Dimensions ◽

Embryonic Cells ◽

Mitotic Spindles ◽

Cleavage Division ◽

Scanning Confocal Microscopy

One of the classic limitations of light microscopy has been the fact that three dimensional biological events could only be visualized in two dimensions. Recently, this shortcoming has been overcome by combining the technologies of laser scanning confocal microscopy (LSCM) and computer processing of microscopical data by volume rendering methods. We have employed these techniques to examine morphogenetic events characterizing early development of sea urchin embryos. Specifically, the fourth cleavage division was examined because it is at this point that the first morphological signs of cell differentiation appear, manifested in the production of macromeres and micromeres by unequally dividing vegetal blastomeres.The mitotic spindle within vegetal blastomeres undergoing unequal cleavage are highly polarized and develop specialized, flattened asters toward the micromere pole. In order to reconstruct the three-dimensional features of these spindles, both isolated spindles and intact, extracted embryos were fluorescently labeled with antibodies directed against either centrosomes or tubulin.

Download Full-text

Automated 3-D cell population analysis in thick tissue sections using laser-scanning confocal-microscopy data

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100148642 ◽

1993 ◽

Vol 51 ◽

pp. 562-563

Author(s):

Hakan Ancin

Keyword(s):

Laser Scanning ◽

Population Analysis ◽

Three Dimensional ◽

Large Data ◽

Laser Scanning Confocal Microscopy ◽

Tissue Slices ◽

Scanning Confocal Microscopy ◽

Tissue Sections ◽

Spatially Adaptive ◽

Microscopy Data

This paper presents methods for performing detailed quantitative automated three dimensional (3-D) analysis of cell populations in thick tissue sections while preserving the relative 3-D locations of cells. Specifically, the method disambiguates overlapping clusters of cells, and accurately measures the volume, 3-D location, and shape parameters for each cell. Finally, the entire population of cells is analyzed to detect patterns and groupings with respect to various combinations of cell properties. All of the above is accomplished with zero subjective bias.In this method, a laser-scanning confocal light microscope (LSCM) is used to collect optical sections through the entire thickness (100 - 500μm) of fluorescently-labelled tissue slices. The acquired stack of optical slices is first subjected to axial deblurring using the expectation maximization (EM) algorithm. The resulting isotropic 3-D image is segmented using a spatially-adaptive Poisson based image segmentation algorithm with region-dependent smoothing parameters. Extracting the voxels that were labelled as "foreground" into an active voxel data structure results in a large data reduction.

Download Full-text

Advanced Static and Dynamic Fluorescence Microscopy Techniques to Investigate Drug Delivery Systems

Pharmaceutics ◽

10.3390/pharmaceutics13060861 ◽

2021 ◽

Vol 13 (6) ◽

pp. 861

Author(s):

Jacopo Cardellini ◽

Arianna Balestri ◽

Costanza Montis ◽

Debora Berti

Keyword(s):

Drug Delivery ◽

Fluorescence Microscopy ◽

Drug Delivery Systems ◽

Laser Scanning ◽

Super Resolution ◽

Laser Scanning Confocal Microscopy ◽

Delivery Systems ◽

Scanning Confocal Microscopy ◽

Biological Phenomena

In the past decade(s), fluorescence microscopy and laser scanning confocal microscopy (LSCM) have been widely employed to investigate biological and biomimetic systems for pharmaceutical applications, to determine the localization of drugs in tissues or entire organisms or the extent of their cellular uptake (in vitro). However, the diffraction limit of light, which limits the resolution to hundreds of nanometers, has for long time restricted the extent and quality of information and insight achievable through these techniques. The advent of super-resolution microscopic techniques, recognized with the 2014 Nobel prize in Chemistry, revolutionized the field thanks to the possibility to achieve nanometric resolution, i.e., the typical scale length of chemical and biological phenomena. Since then, fluorescence microscopy-related techniques have acquired renewed interest for the scientific community, both from the perspective of instrument/techniques development and from the perspective of the advanced scientific applications. In this contribution we will review the application of these techniques to the field of drug delivery, discussing how the latest advancements of static and dynamic methodologies have tremendously expanded the experimental opportunities for the characterization of drug delivery systems and for the understanding of their behaviour in biologically relevant environments.

Download Full-text