scholarly journals A multiphysics model of processes in electromagnets and actuators of vacuum switching devices taking into ac-count contact interaction of structural elements

Author(s):  
Mykhailo Panteliat ◽  
Artem Kuzmin

The purpose of the work is to improve mathematical models and algorithms of computer modeling of multiphysics processes in electromagnets and actuators of vacuum switching devices by taking into account the contact interaction of structural elements when changing their stress-strain state. In the design of modern vacuum circuit breakers and contactors, there is a significant use of electromagnetic actuators based on high-coercive hard magnetic rare earth composite materials NdFeB and SmCo. The most promising for use as drives of circuit breakers and contactors are polarized electromagnets based on the use of these high-coercive permanent magnets. However, the existing serial designs of electromagnets and actuators need to be significantly improved in order to increase reliability and service life, reduce weight and cost, further reduce energy consumption, improve the manufacturability of the mass production process. Computer simulation is proposed to be performed by the Finite Element Method in 2D formulation using commercial software products and/or software created directly for these investigations. One of the priority areas for improving mathematical models and algorithms for computer modeling of processes in the mechanical circuit of vacuum switching devices of medium and high voltage is to take into account the contact interaction of the structural elements of the devices under consideration. The next step, thanks to the use of an advanced mathematical model, is to perform a set of computational research and based on the obtained numerical results to develop recommendations aimed at creating designs of electromagnets and actuators that would meet world standards and be competitive in the world market.

2021 ◽  
Author(s):  
Andrey Manukovskiy ◽  
I. Efremov

This article discusses the features of the development and applicationBIM technologies in the preparation of BIM projects for timber roads in the Russian Federation. The main types of software products used in the preparation of BIM-projects of forest roads have been established. The procedure for using software products is given, their main types are established and functional capabilities are analyzed. The drawbacks and limitations of software products for general-purpose project management in the context of the use of BIM technologies are identified. The necessity of developing a specialized software product for the preparation of elements of projects for the organization of construction «Planworks», in order to increase the efficiency of the use of BIM-technologies in the preparation of projects of timber haul roads. The article describes the proposed procedure for using the developed software product, and also formulates the main stages of developing a project for organizing construction in it. The main list of the initial data required for the preparation of the organization’s project in the developed software product is disclosed. The features of the automated generation of a network model of tasks for the construction of structural elements of a timber road are described, the main types of generated tasks, as well as the features of automated task linking, are given. The advantages of using the developed software product at the stages of development of a technical design and construction of a timber road have been determined.


1988 ◽  
Vol 20 (9) ◽  
pp. 1231-1235
Author(s):  
V. I. Grishin ◽  
T. K. Begeev

2016 ◽  
Vol 78 (9) ◽  
Author(s):  
Izzati Yusri ◽  
Mariam Md Ghazaly ◽  
Esmail Ali Ali Alandoli ◽  
Mohd Fua'ad Rahmat ◽  
Zulkeflee Abdullah ◽  
...  

This paper addresses a rotary motion type of electromagnetic actuator that compares two types of electromagnetic actuators; i.e the Permanent Magnet Switching Flux (PMSF) and the Switching Reluctance (SR) actuator. The Permanent Magnet Switching Flux (PMSF) actuator is the combination of permanent magnets (PM) and the Switching Reluctance (SR) actuator. The force optimizations are accomplished by manipulating the actuator parameters; i.e. (i) the poles ratio of the stator and rotor; (ii) the actuator’s size; (iii) the number of winding turns; and (iv) the air gap thickness between the stator and rotor through Finite Element Analysis Method (FEM) using the ANSYS Maxwell 3D software. The materials implemented in the actuator’s parameters optimizations are readily available materials, especially in Malaysia. The excitation current used in FEM analysis for both actuators was between 0A and 2A with interval of 0.25A. Based on the FEM analyses, the best result was achieved by the Permanent Magnet Switching Flux (PMSF) actuator. The PMSF actuator produced the largest magnetostatic thrust force (4.36kN) once the size is scaled up to 100% with the input current, 2A respectively. The maximum thrust force generated by the Switching Reluctance (SR) actuator was 168.85μN, which is significantly lower in compared to the results of the PMSF actuator. 


2018 ◽  
Vol 16 ◽  
pp. 03001 ◽  
Author(s):  
Lucjan Setlak ◽  
Rafał Kowalik

Based on the analysis and mathematical models of synchronous electric machines (motor/generator), basing on permanent magnets, presented in this paper, the main importance of alternator AC power sources in the form of starter/generator (for conventional aircraft) and in the form of integrated unit starter (motor)/AC synchronous generator S/G AC (with respect to advanced aircraft concept in terms of more electric aircraft) was highlighted. Additionally, through the analysis and selected simulations of the on-board autonomous power supply system of the modern aircrafts, sources of electrical energy (synchronous motor/generator, integrated unit starter/AC generator) were located in board autonomic power system ASE (EPS, PES). Main components of this system are the electro-energetic power system EPS and the energo-electronic power system PES. In addition, the analysis and exemplary simulations of main electricity sources based on mathematical models have contributed to highlighting the main practical applications in accordance with the concept of MEA.


2014 ◽  
Vol 670-671 ◽  
pp. 732-735 ◽  
Author(s):  
Pavel I. Novikov

The distinctive paper is devoted to problem of identification the dynamic characteristics of mathematical models based on the measured dynamic characteristics of real constructions. It is describes a problem of discrepancy of measured and modeling eigen pairs. It is shown that the problem is systemic. The creation and verification processes of mathematical (finite element) models used in the design constructions need some work and adjustments. For a reliable analysis of the construction ways are suggested to overcome the identified gaps using adaptive procedures.


2021 ◽  
Vol 2021 ◽  
pp. 1-23
Author(s):  
Karpenko Vasily Nikolaevich ◽  
Yuriy Starodub ◽  
Andrii Havrys

In the article, investigation is given of the developed mathematical models of nonequilibrium in time and distributed in space thermodynamic state of Earth’s matter from its center to its surface depending on the cases of the presence and absence of an internal source of thermal energy concentrated in the center of mass taking into account known geophysical data about the nucleus, mantle, lithosphere and atmosphere, and endogenous and exogenous heat fluxes. The objects of research are as follows: mathematical models of geothermal energy of the Earth, its internal source, and heat balance of endogenous and exogenous heat fluxes on the Earth’s surface. Research methods used are as follows: thermometry in deep wells, ground and remote sensing of heat fluxes of the Earth and the planets of the Solar System, mathematical modeling of heat exchange and thermoelastic processes from compression of Earth’s matter by gravitational field energy information and classical physical and mathematical methods, and computer modeling. The aim of research: in computer modeling to provide new mathematical models that determine the geophysical parameters of geothermal energy, which are aimed on solving problems of energy, environmental and economic security of society, using modern technical means of calculating ground and remote sensing data development of geothermal resources, and regulation of the heat balance of the ecosystem, namely: (i) study of the geological structure of the lithosphere to a depth of 10 km by remote sensing to determine the physical parameters of its layers more accurately than ground methods; (ii) development of projects of geothermal power plants on the basis of single isolated wells of a given depth with a capacity of up to 2 ÷ 3 mW of electricity on continents of the globe; (iii) real-time monitoring and forecasting of the temperature field of the atmosphere according to its physical and chemical composition. The novelty of the obtained research results: (i) developed the mathematical model of the physical process of origin and distribution in the bowels of the density of geothermal energy of the Earth from the surface to its center, which is the density of internal energy of an elementary geological object, and which increases when approaching the center of the planet; (ii) developed the mathematical model of the thermal energy source of infrared (IR) waves of the elementary geophysical object of the Earth’s interior depending on the depth of its occurrence, which allows to determine the stable generation of geothermal energy by rocks in a deep well for extraction and conversion into electricity and to study the geological structure and physical properties of the Earth’s interior; (iii) the mathematical model of heat exchange between the layers of the Earth’s subsoil with the thermal energy of infrared waves according to the laws of Fourier thermal conductivity and Stefan–Boltzmann heat transfer, which together with the geothermal energy source model allows to determine a thermal capacity of rocks in a deep well; (iv) developed the mathematical model of stable action of a source of thermal energy in the center of mass of the Earth, in the absence of which it is hard to explain the power of its endogenous infrared heat flux, parameters of geothermal energy distribution in the Earth, and the current thermodynamic state of the atmosphere, and the change in temperature of which depends on the thermophysical parameters of the physical-chemical composition of the atmosphere more than on changes in the thermal activity of the Sun; (v) determination of new numerical values: thermophysical parameters of the Earth’s interior; kinetic, potential and own gravitational energy of the Earth and own gravitational energy of the planets of the Solar System.


Author(s):  
Y. Get'man ◽  
A. Pogonin ◽  
Y. Bondarenko

At first glance, a rotary kiln is a simple structural object, which is very widespread in the industry of processing and obtaining materials, both for construction and for other purposes. However, behind the external simplicity, there are complex chemical processes, mechanical, subtleties of the control system, the technology of manufacturing large-sized parts that are part of the general assembly and directly issues related to the design and modernization stage. The study of various regularities of mechanical processes associated with the theory of elasticity, kinematics and contact interactions is difficult even separately, especially when the processes run together. Studying the contact interaction of the kiln with roller supports allows to see the anomalous effects that can occur if the design is incorrect. In a specific case, it is necessary to observe how, under the action of external forces, time-varying deformations, displacements, of individual structural elements occur, which are of key functional importance in the operation of the equipment, in conditions of contact interaction of its individual parts, taking into account inertial loads and damping. The study of transition processes with changing force factors in time will allow to obtain the response of the structure to external influences


2020 ◽  
Vol 1 (14) ◽  
pp. 111-114
Author(s):  
Svetlana Senotova ◽  
Andrey Maslyuchenko

The article discusses the differential equations of motion of the orbital cable system. Systems of equations are solved by the Euler method and the Runge-Kutt method. Programs are written in Python in the graphic editor Blender with a visual representation of mathematical models


Sign in / Sign up

Export Citation Format

Share Document