Estimating In-Situ Permeabilities for Reservoir Simulation Using Multi-Variable Transforms: Two Case Studies

1989 ◽  
Author(s):  
B.S. Carr ◽  
S.L. Metcalfe ◽  
N.G. Saleri
2018 ◽  
pp. 60-67
Author(s):  
Henrika Pihlajaniemi ◽  
Anna Luusua ◽  
Eveliina Juntunen

This paper presents the evaluation of usersХ experiences in three intelligent lighting pilots in Finland. Two of the case studies are related to the use of intelligent lighting in different kinds of traffic areas, having emphasis on aspects of visibility, traffic and movement safety, and sense of security. The last case study presents a more complex view to the experience of intelligent lighting in smart city contexts. The evaluation methods, tailored to each pilot context, include questionnaires, an urban dashboard, in-situ interviews and observations, evaluation probes, and system data analyses. The applicability of the selected and tested methods is discussed reflecting the process and achieved results.


2020 ◽  
Vol 49 (4) ◽  
pp. 579-595
Author(s):  
José Alberto BATISTA RODRÍGUEZ ◽  
Edgar Niño RODRÍGUEZ ◽  
Pedro Antonio RODRÍGUEZ RIOJAS ◽  
Roberto DÍAZ MARTÍNEZ ◽  
Antonio RODRÍGUEZ VEGA ◽  
...  

2019 ◽  
Vol 19 (14) ◽  
pp. 9181-9208 ◽  
Author(s):  
Kristina Pistone ◽  
Jens Redemann ◽  
Sarah Doherty ◽  
Paquita Zuidema ◽  
Sharon Burton ◽  
...  

Abstract. The total effect of aerosols, both directly and on cloud properties, remains the biggest source of uncertainty in anthropogenic radiative forcing on the climate. Correct characterization of intensive aerosol optical properties, particularly in conditions where absorbing aerosol is present, is a crucial factor in quantifying these effects. The southeast Atlantic Ocean (SEA), with seasonal biomass burning smoke plumes overlying and mixing with a persistent stratocumulus cloud deck, offers an excellent natural laboratory to make the observations necessary to understand the complexities of aerosol–cloud–radiation interactions. The first field deployment of the NASA ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) campaign was conducted in September of 2016 out of Walvis Bay, Namibia. Data collected during ORACLES-2016 are used to derive aerosol properties from an unprecedented number of simultaneous measurement techniques over this region. Here, we present results from six of the eight independent instruments or instrument combinations, all applied to measure or retrieve aerosol absorption and single-scattering albedo. Most but not all of the biomass burning aerosol was located in the free troposphere, in relative humidities typically ranging up to 60 %. We present the single-scattering albedo (SSA), absorbing and total aerosol optical depth (AAOD and AOD), and absorption, scattering, and extinction Ångström exponents (AAE, SAE, and EAE, respectively) for specific case studies looking at near-coincident and near-colocated measurements from multiple instruments, and SSAs for the broader campaign average over the month-long deployment. For the case studies, we find that SSA agrees within the measurement uncertainties between multiple instruments, though, over all cases, there is no strong correlation between values reported by one instrument and another. We also find that agreement between the instruments is more robust at higher aerosol loading (AOD400>0.4). The campaign-wide average and range shows differences in the values measured by each instrument. We find the ORACLES-2016 campaign-average SSA at 500 nm (SSA500) to be between 0.85 and 0.88, depending on the instrument considered (4STAR, AirMSPI, or in situ measurements), with the interquartile ranges for all instruments between 0.83 and 0.89. This is consistent with previous September values reported over the region (between 0.84 and 0.90 for SSA at 550nm). The results suggest that the differences observed in the campaign-average values may be dominated by instrument-specific spatial sampling differences and the natural physical variability in aerosol conditions over the SEA, rather than fundamental methodological differences.


2019 ◽  
Vol 36 (9) ◽  
pp. 1693-1711 ◽  
Author(s):  
A. C. P. Oude Nijhuis ◽  
C. M. H. Unal ◽  
O. A. Krasnov ◽  
H. W. J. Russchenberg ◽  
A. G. Yarovoy

In this article, five velocity-based energy dissipation rate (EDR) retrieval techniques are assessed. The EDR retrieval techniques are applied to Doppler measurements from Transportable Atmospheric Radar (TARA)—a precipitation profiling radar—operating in the vertically fixed-pointing mode. A generalized formula for the Kolmogorov constant is derived, which gives potential for the application of the EDR retrieval techniques to any radar line of sight (LOS). Two case studies are discussed that contain rain events of about 2 and 18 h, respectively. The EDR values retrieved from the radar are compared to in situ EDR values from collocated sonic anemometers. For the two case studies, a correlation coefficient of 0.79 was found for the wind speed variance (WSV) EDR retrieval technique, which uses 3D wind vectors as input and has a total sampling time of 10 min. From this comparison it is concluded that the radar is able to measure EDR with a reasonable accuracy. Almost no correlation was found for the vertical wind velocity variance (VWVV) EDR retrieval technique, as it was not possible to sufficiently separate the turbulence dynamics contribution to the radar Doppler mean velocities from the velocity contribution of falling raindrops. An important cause of the discrepancies between radar and in situ EDR values is thus due to insufficient accurate estimation of vertical air velocities.


2001 ◽  
Vol 41 (1) ◽  
pp. 609
Author(s):  
X. Chen ◽  
C.P. Tan ◽  
C.M. Haberfield

To prevent or minimise wellbore instability problems, it is critical to determine the optimum wellbore profile and to design an appropriate mud weight program based on wellbore stability analysis. It is a complex and iterative decisionmaking procedure since various factors, such as in-situ stress regime, material strength and poroelastic properties, strength and poroelastic anisotropies, initial and induced pore pressures, must be considered in the assessment and determination.This paper describes the methodology and procedure for determination of optimum wellbore profile and mud weight program based on rock mechanics consideration. The methodology is presented in the form of guideline charts and the procedure of applying the methodology is described. The application of the methodology and procedure is demonstrated through two field case studies with different in-situ stress regimes in Australia and Indonesia.


Sign in / Sign up

Export Citation Format

Share Document