Safeguarding CO2 Storage in a Depleted Offshore Gas Field with Adaptive Approach of Monitoring, Measurement and Verification MMV

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Prasanna Chidambaram ◽  
Ahmad Ismail Azahree ◽  
Debasis Priyadarshan Das ◽  
Parimal Arjun Patil ◽  
...  
Keyword(s):  
Co2 Sequestration ◽  
Co2 Storage ◽  
Storage Site ◽  
Injection Wells ◽  
Plume Front ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic ◽  
And Storage

Abstract CO2 sequestration is a process for eternity with a possibility of zero-degree failure. One of the key components of the CO2 Sequestration Project is to have a site-specific, risk-based and adaptive Monitoring, Measurement and Verification (MMV) plan. The storage site has been studied thoroughly and is understood to be inherently safe for CO2 sequestration. However, it is incumbent on operator to manage and minimize storage risks. MMV planning is critical along with geological site selection, transportation and storage process. Geological evaluation study of the storage site suggests the containment capacity of identified large depleted gas reservoirs as well as long term conformance due to thick interval. The fault-seal analysis and reservoir integrity study contemplate long-term security of the CO2 storage. An integrated 3D reservoir dynamic simulation model coupled with geomechanical and geochemical models were performed. This helps in understanding storage capacity, trapping mechanisms, reservoir integrity, plume migration path, and injectivity. To demonstrate that CO2 plume migration can be mapped from the seismic, a 4D Seismic feasibility study was carried out using well and fluid data. Gassmann fluid substitution was performed in carbonate reservoir at well, and seismic response of several combination of fluid saturation scenarios on synthetic gathers were analyzed. The CO2 dispersion study, which incorporate integration of subsurface, geomatic and metocean & environment data along with leakage character information, was carried out to understand the potential leakage pathway along existing wells and faults which enable to design a monitoring plan accordingly. The monitoring of wells & reservoir integrity, overburden integrity will be carried out by Fiber Optic System to be installed in injection wells. Significant difference in seismic amplitude observed at the reservoir top during 4D seismic feasibility study for varying CO2 saturation suggests that monitoring of CO2 plume migration from seismic is possible. CO2 plume front with as low as 25% saturation can be discriminated provided seismic data has high signal noise ratio (SNR). 3D DAS-VSP acquisition modeling results show that a subsurface coverage of approximately 3 km2 per well is achievable. Laboratory injectivity studies and three-way coupled modelling simulations established that three injection wells will be required to achieve the target injection rate. As planned injection wells are field centric and storage site area is large, DAS-VSP find limited coverage to monitor the CO2 plume front. Hence, surface seismic acquisition will be an integral component of full field monitoring and time-lapsed evaluations for integrated MMV planning to monitor CO2 plume migration. The integrated MMV planning is designed to ensure that injected CO2 in the reservoir is intact and safely stored for hundreds of years after injection. Field specific MMV technologies for CO2 plume migration with proactive approach were identified after exercising pre-defined screening criteria.

Offshore MMV Planning for Sustainability of CO2 Storage in a Depleted Carbonate Reservoir, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Debasis Priyadarshan Das ◽  
Parimal Arjun Patil ◽  
Prasanna Chidambaram ◽  
Zoann Low ◽  
...  
Keyword(s):  
Co2 Sequestration ◽  
Co2 Storage ◽  
Carbonate Reservoir ◽  
Co2 Injection ◽  
Storage Site ◽  
Gas Field ◽  
Plume Migration ◽  
Co2 Plume ◽  
The Impact

Abstract CO2 sequestration is a process for eternity with a possibility of zero-degree failure. Monitoring, Measurement and Verification (MMV) planning of CO2 sequestration is crucial along with geological site selection, transportation and injection process. Several geological formations have been evaluated in the past for potential storage site which divulges the containment capacity of identified large, depleted gas reservoirs as well as long term conformance. Offshore environment makes MMV plan challenging and demands rigorous integration of monitoring technologies to optimize project economic and involved logistics. The role of MMV is critical for sustainability of the CO2 storage project as it ensures that injected CO2 in the reservoir is intact and safely stored for hundreds of years post-injection. Field specific MMV technologies for CO2 plume migration with proactive approach were identified after exercising pre-defined screening criteria. Marine CO2 dispersion study is carried out to confirm the impact of any potential leakage along existing wells and faults, and to understand the CO2 behavior in marine environment in the event of leakage. Study incorporates integration of G&G subsurface and Meta-Ocean & Environment data along with other leakage character information. Multi-Fiber Optic Sensors System (M-FOSS) to be installed in injector wells for monitoring well & reservoir integrity, overburden integrity and monitoring of early CO2 plume migration by acquiring & analyzing the distributed sensing data (DTS/DPS/DAS/DSS). Based on 3D couple modeling, a maximum injection rate of approximately 200 MMscfd of permeate stream produced from a high CO2 contaminated gas field can be achieved. Injectivity studies indicate that over 100 MMSCFD of CO2 injection rates into depleted gas reservoir is possible from a single injector. Injectivity results are integrated with dynamic simulation to determine number and location of injector wells. 3D DAS-VSP simulation results show that a subsurface coverage of approximately 3 km2 per well is achievable, which along with simulated CO2 plume extent help to determine the number of wells required to get maximum monitoring coverage for the MMV planning. As planned injector wells are field centric and storage site area is large, DAS-VSP find limited coverage to monitor the CO2 plume. To overcome this challenge, requirement of surface seismic acquisition survey is recommended for full field monitoring. An integrated MMV plan is designed for cost-effective long-term offshore monitoring of CO2 plume migration. The present study discusses the impacting parameters which make the whole process environmentally sustainable, economically viable and adhering to national and international regulations.

3D DAS-VSP Illumination Modeling for CO2 Plume Migration Monitoring in Offshore Sarawak, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Zoann Low ◽  
Parimal Arjun Patil ◽  
Debasis Priyadarshan Das ◽  
Prasanna Chidambaram ◽  
...  
Keyword(s):  
Dynamic Simulation ◽  
Seismic Velocity ◽  
Time Lapse ◽  
Carbonate Reservoir ◽  
Fiber Optic Sensor ◽  
Co2 Injection ◽  
Storage Site ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic

Abstract Monitoring of CO2 plume migration in a depleted carbonate reservoir is challenging and demand comprehensive and trailblazing monitoring technologies. 4D time-lapse seismic exhibits the migration of CO2 plume within geological storage but in the area affected by gas chimney due to poor signal-to-noise ratio (SNR), uncertainty in identifying and interpretation of CO2 plume gets exaggerated. High resolution 3D vertical seismic profile (VSP) survey using distributed acoustic sensor (DAS) technology fulfil the objective of obtaining the detailed subsurface image which include CO2 plume migration, reservoir architecture, sub-seismic faults and fracture networks as well as the caprock. Integration of quantitative geophysics and dynamic simulation with illumination modelling dignify the capabilities of 3D DAS-VSP for CO2 plume migration monitoring. The storage site has been studied in detailed and an integrated coupled dynamic simulation were performed and results were integrated with seismic forward modeling to demonstrate the CO2 plume migration with in reservoir and its impact on seismic amplitude. 3D VSP illumination modelling was carried out by integrating reservoir and overburden interpretations, acoustic logs and seismic velocity to illustrate the subsurface coverage area at top of reservoir. Several acquisition survey geometries were simulated based on different source carpet size for effective surface source contribution for subsurface illumination and results were analyzed to design the 3D VSP survey for early CO2 plume migration monitoring. The illumination simulation was integrated with dynamic simulation for fullfield CO2 plume migration monitoring with 3D DAS-VSP by incorporating Pseudo wells illumination analysis. Results of integrated coupled dynamic simulation and 4D seismic feasibility were analyzed for selection of best well location to deploy the multi fiber optic sensor system (M-FOSS) technology. Amplitude response of synthetic AVO (amplitude vs offsets) gathers at the top of carbonate reservoir were analyzed for near, mid and far angle stacks with respect to pre-production as well as pre-injection reservoir conditions. Observed promising results of distinguishable 25-30% of CO2 saturation in depleted reservoir from 4D time-lapse seismic envisage the application of 3D DAS-VSP acquisition. The source patch analysis of 3D VSP illumination modelling results indicate that a source carpet of 6km×6km would be cos-effectively sufficient to produce a maximum of approximately 2km in diameter subsurface illumination at the top of the reservoir. The Pseudo wells illumination analysis results show that current planned injection wells would probably able to monitor early CO2 injection but for the fullfield monitoring additional monitoring wells or a hybrid survey of VSP and surface seismic would be required. The integrated modeling approach ensures that 4D Seismic in subsurface CO2 plume monitoring is robust. Monitoring pressure build-ups from 3D DAS-VSP will reduce the associated risks.

Tracking a Deep Co2 Plume: 4d Seismic Imaging at the Aquistore Co2 Storage Site, Saskatchewan, Canada

2019 ◽  
Author(s):  
Don White ◽  
Kyle Harris ◽  
Lisa Roach ◽  
Saeid Cheraghi ◽  
Brian Roberts ◽  
...  
Keyword(s):  
Seismic Imaging ◽  
Co2 Storage ◽  
Storage Site ◽  
Co2 Plume ◽  
4D Seismic

scholarly journals Numerical Simulation and Optimization of CO2 Sequestration in Saline Aquifers

2012 ◽  
Author(s):  
Zheming Zhang ◽  
Ramesh Agarwal
Keyword(s):  
Numerical Simulation ◽  
Co2 Sequestration ◽  
Storage Capacity ◽  
Co2 Storage ◽  
Injection Well ◽  
Co2 Injection ◽  
Great Promise ◽  
Saline Aquifer ◽  
Simulation And Optimization ◽  
Co2 Plume

With recent concerns on CO2 emissions from coal fired electricity generation plants; there has been major emphasis on the development of safe and economical Carbon Dioxide Capture and Sequestration (CCS) technology worldwide. Saline reservoirs are attractive geological sites for CO2 sequestration because of their huge capacity for sequestration. Over the last decade, numerical simulation codes have been developed in U.S, Europe and Japan to determine a priori the CO2 storage capacity of a saline aquifer and provide risk assessment with reasonable confidence before the actual deployment of CO2 sequestration can proceed with enormous investment. In U.S, TOUGH2 numerical simulator has been widely used for this purpose. However at present it does not have the capability to determine optimal parameters such as injection rate, injection pressure, injection depth for vertical and horizontal wells etc. for optimization of the CO2 storage capacity and for minimizing the leakage potential by confining the plume migration. This paper describes the development of a “Genetic Algorithm (GA)” based optimizer for TOUGH2 that can be used by the industry with good confidence to optimize the CO2 storage capacity in a saline aquifer of interest. This new code including the TOUGH2 and the GA optimizer is designated as “GATOUGH2”. It has been validated by conducting simulations of three widely used benchmark problems by the CCS researchers worldwide: (a) Study of CO2 plume evolution and leakage through an abandoned well, (b) Study of enhanced CH4 recovery in combination with CO2 storage in depleted gas reservoirs, and (c) Study of CO2 injection into a heterogeneous geological formation. Our results of these simulations are in excellent agreement with those of other researchers obtained with different codes. The validated code has been employed to optimize the proposed water-alternating-gas (WAG) injection scheme for (a) a vertical CO2 injection well and (b) a horizontal CO2 injection well, for optimizing the CO2 sequestration capacity of an aquifer. These optimized calculations are compared with the brute force nearly optimized results obtained by performing a large number of calculations. These comparisons demonstrate the significant efficiency and accuracy of GATOUGH2 as an optimizer for TOUGH2. This capability holds a great promise in studying a host of other problems in CO2 sequestration such as how to optimally accelerate the capillary trapping, accelerate the dissolution of CO2 in water or brine, and immobilize the CO2 plume.

Effect of brine salinity on CO2 plume migration and trapping capacity in deep saline aquifers

2017 ◽  
Vol 57 (1) ◽  
pp. 100 ◽  
Author(s):  
Emad A. Al-Khdheeawi ◽  
Stephanie Vialle ◽  
Ahmed Barifcani ◽  
Mohammad Sarmadivaleh ◽  
Stefan Iglauer
Keyword(s):  
Co2 Storage ◽  
Three Dimensional ◽  
Rock Properties ◽  
Saline Aquifers ◽  
Migration Distance ◽  
Deep Saline Aquifer ◽  
Plume Migration ◽  
Co2 Plume ◽  
Wet Rocks ◽  
Brine Salinity

CO2 migration and storage capacity are highly affected by various parameters (e.g. reservoir temperature, vertical to horizontal permeability ratio, cap rock properties, aquifer depth and the reservoir heterogeneity). One of these parameters, which has received little attention, is brine salinity. Although brine salinity has been well demonstrated previously as a factor affecting rock wettability (i.e. higher brine salinity leads to more CO2-wet rocks), its effect on the CO2 storage process has not been addressed effectively. Thus, we developed a three-dimensional homogeneous reservoir model to simulate the behaviour of a CO2 plume in a deep saline aquifer using five different salinities (ranging from 2000 to 200 000 ppm) and have predicted associated CO2 migration patterns and trapping capacities. CO2 was injected at a depth of 1408 m for a period of 1 year at a rate of 1 Mt year–1 and then stored for the next 100 years. The results clearly indicate that 100 years after the injection of CO2 has stopped, the salinity has a significant effect on the CO2 migration distance and the amount of mobile, residual and dissolved CO2. First, the results show that higher brine salinity leads to an increase in CO2 mobility and CO2 migration distance, but reduces the amount of residually trapped CO2. Furthermore, high brine salinity leads to reduced dissolution trapping. Thus, we conclude that less-saline aquifers are preferable CO2 sinks.

scholarly journals Maturing global CO2 storage resources on offshore continental margins to achieve 2DS emissions reductions

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
P. S. Ringrose ◽  
T. A. Meckel
Keyword(s):  
Large Scale ◽  
Storage Capacity ◽  
Pore Space ◽  
Co2 Storage ◽  
Emissions Reduction ◽  
Continental Margins ◽  
Emissions Reductions ◽  
Injection Wells ◽  
Reduction Strategies

AbstractMost studies on CO2 emissions reduction strategies that address the ‘two-degree scenario’ (2DS) recognize a significant role for CCS. For CCS to be effective, it must be deployed globally on both existing and emerging energy systems. For nations with large-scale emissions, offshore geologic CO2 storage provides an attractive and efficient long-term strategy. While some nations are already developing CCS projects using offshore CO2 storage resources, most geographic regions have yet to begin. This paper demonstrates the geologic significance of global continental margins for providing broadly-equitable, geographically-relevant, and high-quality CO2 storage resources. We then use principles of pore-space utilization and subsurface pressure constraints together with analogs of historic industry well deployment rates to demonstrate how the required storage capacity can be developed as a function of time and technical maturity to enable the global deployment of offshore storage for facilitating 2DS. Our analysis indicates that 10–14 thousand CO2 injection wells will be needed globally by 2050 to achieve this goal.

Assessment of 4D seismic repeatability and CO2 detection limits using a sparse permanent land array at the Aquistore CO2 storage site

Geophysics ◽  
2015 ◽  
Vol 80 (2) ◽  
pp. WA1-WA13 ◽  
Author(s):  
Lisa A. N. Roach ◽  
Donald J. White ◽  
Brian Roberts
Keyword(s):  
Co2 Storage ◽  
Time Lapse ◽  
Data Sets ◽  
Storage Site ◽  
Processing Sequence ◽  
Time Migration ◽  
Receiver Array ◽  
Co2 Detection ◽  
4D Seismic ◽  
The Impact

Two 3D time-lapse seismic surveys were acquired in 2012 and 2013 at the Aquistore [Formula: see text] storage site prior to the start of [Formula: see text] injection. Using these surveys, we determined the background time-lapse noise at the site and assessed the feasibility of using a sparse areal permanent receiver array as a monitoring tool. Applying a standard processing sequence to these data, we adequately imaged the reservoir at 3150–3350 m depth. Evaluation of the impact of each processing step on the repeatability revealed a general monotonic increase in similarity between the data sets as a function of processing. The prestack processing sequence reduced the normalized root mean squared difference (nrms) from 1.13 between the raw stacks to 0.13 after poststack time migration. The postmigration cross-equalization sequence further reduced the global nrms to 0.07. A simulation of the changes in seismic response due to a range of [Formula: see text] injection scenarios suggested that [Formula: see text] was detectable within the reservoir at the Aquistore site provided that zones of greater thickness than 6–13 m have reached [Formula: see text] saturations of greater than 5%.

scholarly journals The Endurance CO2 storage site, Blocks 42/25 and 43/21, UK North Sea

2020 ◽  
Vol 52 (1) ◽  
pp. 163-171 ◽  
Author(s):  
Jon G. Gluyas ◽  
Usman Bagudu
Keyword(s):  
Carbon Capture ◽  
Co2 Storage ◽  
Carbon Capture And Storage ◽  
Lower Triassic ◽  
Injection Rate ◽  
Government Support ◽  
Storage Site ◽  
Sandstone Formation ◽  
The Uk ◽  
And Storage

AbstractThe Endurance, four-way, dip-closed structure in UK Blocks 42/25 and 43/21 occurs over a salt swell diapir and within Triassic and younger strata. The Lower Triassic Bunter Sandstone Formation reservoir within the structure was tested twice for natural gas (in 1970 and 1990) but both wells were dry. The reservoir is both thick and high quality and, as such, an excellent candidate site for subsurface CO2 storage.In 2013 a consortium led by National Grid Carbon drilled an appraisal well on the structure and undertook an injection test ahead of a planned development of Endurance as the first bespoke storage site on the UK Continental Shelf with an expected injection rate of 2.68 × 106 t of dense phase CO2 each year for 20 years. The site was not developed following the UK Government's removal of financial support for carbon capture and storage (CCS) demonstration projects, but it is hoped with the recent March 2020 Budget that government support for CCS may now be back on track.

Bio-Energy Cogeneration Systems With CO2 Separation and Storage

2004 ◽  
Author(s):  
C. Hochenauer ◽  
U. Hohenwarter ◽  
W. Sanz ◽  
B. Schlamadinger
Keyword(s):  
Co2 Sequestration ◽  
Pure Oxygen ◽  
Co2 Removal ◽  
Permanent Storage ◽  
Cogeneration System ◽  
Shift Reaction ◽  
The Cost ◽  
And Storage ◽  
Plant Efficiency

This paper compares three different bio-energy cogeneration power station concepts where CO2 is sequestered and available for permanent storage instead of discharging into the atmosphere. The different bio-energy cogeneration systems are: The pre-combustion capture of CO2 the post-combustion capture of CO2 from the flue gas and the combustion in an atmosphere of pure oxygen (Graz-Cycle). The three schemes, all based on a thermal input of about 150 MWth, are compared on the basis of their technological features, their performance, projected costs of electricity and CO2 mitigation costs. Compared to a conventional bio-energy cogeneration system, CO2 removal reduces net plant efficiency by 11 to 16 percentage points and increases the cost of electricity by approximately 54 to 89%. The scheme applying reforming and shift reaction and physical absorption of the syngas fuel appears the most appealing option for the short-term implementation of CO2 sequestration bio-energy cogeneration systems. The Graz-Cycle where the syngas is burnt in pure oxygen appears the most appealing option for the long-term option for CO2 sequestration.

Sign in / Sign up

Export Citation Format

Share Document