Offshore MMV Planning for Sustainability of CO2 Storage in a Depleted Carbonate Reservoir, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Debasis Priyadarshan Das ◽  
Parimal Arjun Patil ◽  
Prasanna Chidambaram ◽  
Zoann Low ◽  
...  
Keyword(s):  
Co2 Sequestration ◽  
Co2 Storage ◽  
Carbonate Reservoir ◽  
Co2 Injection ◽  
Storage Site ◽  
Gas Field ◽  
Plume Migration ◽  
Co2 Plume ◽  
The Impact

Abstract CO2 sequestration is a process for eternity with a possibility of zero-degree failure. Monitoring, Measurement and Verification (MMV) planning of CO2 sequestration is crucial along with geological site selection, transportation and injection process. Several geological formations have been evaluated in the past for potential storage site which divulges the containment capacity of identified large, depleted gas reservoirs as well as long term conformance. Offshore environment makes MMV plan challenging and demands rigorous integration of monitoring technologies to optimize project economic and involved logistics. The role of MMV is critical for sustainability of the CO2 storage project as it ensures that injected CO2 in the reservoir is intact and safely stored for hundreds of years post-injection. Field specific MMV technologies for CO2 plume migration with proactive approach were identified after exercising pre-defined screening criteria. Marine CO2 dispersion study is carried out to confirm the impact of any potential leakage along existing wells and faults, and to understand the CO2 behavior in marine environment in the event of leakage. Study incorporates integration of G&G subsurface and Meta-Ocean & Environment data along with other leakage character information. Multi-Fiber Optic Sensors System (M-FOSS) to be installed in injector wells for monitoring well & reservoir integrity, overburden integrity and monitoring of early CO2 plume migration by acquiring & analyzing the distributed sensing data (DTS/DPS/DAS/DSS). Based on 3D couple modeling, a maximum injection rate of approximately 200 MMscfd of permeate stream produced from a high CO2 contaminated gas field can be achieved. Injectivity studies indicate that over 100 MMSCFD of CO2 injection rates into depleted gas reservoir is possible from a single injector. Injectivity results are integrated with dynamic simulation to determine number and location of injector wells. 3D DAS-VSP simulation results show that a subsurface coverage of approximately 3 km2 per well is achievable, which along with simulated CO2 plume extent help to determine the number of wells required to get maximum monitoring coverage for the MMV planning. As planned injector wells are field centric and storage site area is large, DAS-VSP find limited coverage to monitor the CO2 plume. To overcome this challenge, requirement of surface seismic acquisition survey is recommended for full field monitoring. An integrated MMV plan is designed for cost-effective long-term offshore monitoring of CO2 plume migration. The present study discusses the impacting parameters which make the whole process environmentally sustainable, economically viable and adhering to national and international regulations.

Safeguarding CO2 Storage in a Depleted Offshore Gas Field with Adaptive Approach of Monitoring, Measurement and Verification MMV

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Prasanna Chidambaram ◽  
Ahmad Ismail Azahree ◽  
Debasis Priyadarshan Das ◽  
Parimal Arjun Patil ◽  
...  
Keyword(s):  
Co2 Sequestration ◽  
Co2 Storage ◽  
Storage Site ◽  
Injection Wells ◽  
Plume Front ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic ◽  
And Storage

Abstract CO2 sequestration is a process for eternity with a possibility of zero-degree failure. One of the key components of the CO2 Sequestration Project is to have a site-specific, risk-based and adaptive Monitoring, Measurement and Verification (MMV) plan. The storage site has been studied thoroughly and is understood to be inherently safe for CO2 sequestration. However, it is incumbent on operator to manage and minimize storage risks. MMV planning is critical along with geological site selection, transportation and storage process. Geological evaluation study of the storage site suggests the containment capacity of identified large depleted gas reservoirs as well as long term conformance due to thick interval. The fault-seal analysis and reservoir integrity study contemplate long-term security of the CO2 storage. An integrated 3D reservoir dynamic simulation model coupled with geomechanical and geochemical models were performed. This helps in understanding storage capacity, trapping mechanisms, reservoir integrity, plume migration path, and injectivity. To demonstrate that CO2 plume migration can be mapped from the seismic, a 4D Seismic feasibility study was carried out using well and fluid data. Gassmann fluid substitution was performed in carbonate reservoir at well, and seismic response of several combination of fluid saturation scenarios on synthetic gathers were analyzed. The CO2 dispersion study, which incorporate integration of subsurface, geomatic and metocean & environment data along with leakage character information, was carried out to understand the potential leakage pathway along existing wells and faults which enable to design a monitoring plan accordingly. The monitoring of wells & reservoir integrity, overburden integrity will be carried out by Fiber Optic System to be installed in injection wells. Significant difference in seismic amplitude observed at the reservoir top during 4D seismic feasibility study for varying CO2 saturation suggests that monitoring of CO2 plume migration from seismic is possible. CO2 plume front with as low as 25% saturation can be discriminated provided seismic data has high signal noise ratio (SNR). 3D DAS-VSP acquisition modeling results show that a subsurface coverage of approximately 3 km2 per well is achievable. Laboratory injectivity studies and three-way coupled modelling simulations established that three injection wells will be required to achieve the target injection rate. As planned injection wells are field centric and storage site area is large, DAS-VSP find limited coverage to monitor the CO2 plume front. Hence, surface seismic acquisition will be an integral component of full field monitoring and time-lapsed evaluations for integrated MMV planning to monitor CO2 plume migration. The integrated MMV planning is designed to ensure that injected CO2 in the reservoir is intact and safely stored for hundreds of years after injection. Field specific MMV technologies for CO2 plume migration with proactive approach were identified after exercising pre-defined screening criteria.

3D DAS-VSP Illumination Modeling for CO2 Plume Migration Monitoring in Offshore Sarawak, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Zoann Low ◽  
Parimal Arjun Patil ◽  
Debasis Priyadarshan Das ◽  
Prasanna Chidambaram ◽  
...  
Keyword(s):  
Dynamic Simulation ◽  
Seismic Velocity ◽  
Time Lapse ◽  
Carbonate Reservoir ◽  
Fiber Optic Sensor ◽  
Co2 Injection ◽  
Storage Site ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic

Abstract Monitoring of CO2 plume migration in a depleted carbonate reservoir is challenging and demand comprehensive and trailblazing monitoring technologies. 4D time-lapse seismic exhibits the migration of CO2 plume within geological storage but in the area affected by gas chimney due to poor signal-to-noise ratio (SNR), uncertainty in identifying and interpretation of CO2 plume gets exaggerated. High resolution 3D vertical seismic profile (VSP) survey using distributed acoustic sensor (DAS) technology fulfil the objective of obtaining the detailed subsurface image which include CO2 plume migration, reservoir architecture, sub-seismic faults and fracture networks as well as the caprock. Integration of quantitative geophysics and dynamic simulation with illumination modelling dignify the capabilities of 3D DAS-VSP for CO2 plume migration monitoring. The storage site has been studied in detailed and an integrated coupled dynamic simulation were performed and results were integrated with seismic forward modeling to demonstrate the CO2 plume migration with in reservoir and its impact on seismic amplitude. 3D VSP illumination modelling was carried out by integrating reservoir and overburden interpretations, acoustic logs and seismic velocity to illustrate the subsurface coverage area at top of reservoir. Several acquisition survey geometries were simulated based on different source carpet size for effective surface source contribution for subsurface illumination and results were analyzed to design the 3D VSP survey for early CO2 plume migration monitoring. The illumination simulation was integrated with dynamic simulation for fullfield CO2 plume migration monitoring with 3D DAS-VSP by incorporating Pseudo wells illumination analysis. Results of integrated coupled dynamic simulation and 4D seismic feasibility were analyzed for selection of best well location to deploy the multi fiber optic sensor system (M-FOSS) technology. Amplitude response of synthetic AVO (amplitude vs offsets) gathers at the top of carbonate reservoir were analyzed for near, mid and far angle stacks with respect to pre-production as well as pre-injection reservoir conditions. Observed promising results of distinguishable 25-30% of CO2 saturation in depleted reservoir from 4D time-lapse seismic envisage the application of 3D DAS-VSP acquisition. The source patch analysis of 3D VSP illumination modelling results indicate that a source carpet of 6km×6km would be cos-effectively sufficient to produce a maximum of approximately 2km in diameter subsurface illumination at the top of the reservoir. The Pseudo wells illumination analysis results show that current planned injection wells would probably able to monitor early CO2 injection but for the fullfield monitoring additional monitoring wells or a hybrid survey of VSP and surface seismic would be required. The integrated modeling approach ensures that 4D Seismic in subsurface CO2 plume monitoring is robust. Monitoring pressure build-ups from 3D DAS-VSP will reduce the associated risks.

Reservoir Characterization for Uncertainty Analysis and Its Impact on CO2 Injection and Sequestration in a Depleted Offshore Carbonate Gas Field

2021 ◽  
Author(s):  
Debasis P. Das ◽  
Parimal A. Patil ◽  
Pankaj K. Tiwari ◽  
Renato J Leite ◽  
Raj Deo Tewari
Keyword(s):  
Co2 Storage ◽  
Assessment Process ◽  
Rock Properties ◽  
Co2 Injection ◽  
Storage Site ◽  
Reservoir Pressure ◽  
Gas Field ◽  
Well Integrity ◽  
Seismic Anomalies

Abstract The emerging global climate change policies have necessitated the strategic need for prudent management of produced contaminants and, with cold flaring being no more the best option, Carbon Capture Utilization & Storage (CCUS) technology provides opportunity for development of high CO2 contaminant fields. A typical CO2 sequestration project comprises capturing CO2 by separating from produced hydrocarbons followed by injection of CO2 into deep geological formations for long term storage. While injection ofCO2 may continue over tens of years, the long-term containment needs to be ascertained for thousands of years. Several geological and geophysical factors along with the existingwells need to be evaluated to assess the potential risks for CO2 leakage that maychallenge the long-term containment. This study considers a depleted carbonate field located offshore Sarawak as a possible long-term CO2 storage site. Elements that may lead to possible leakage of CO2over time are the existing faults or fractures, development of new fractures/faults during injection, caprock failure due to pressures exceeding fracture pressure during/after injection and possible leakage through existing wells. The risk assessment process includes identification and mapping of faults and fracture networks, mapping of seals, evaluation of seismic anomalies and gas while drilling records, pore-pressure analysis, laboratory experiments for analyzing changes in geomechanical & geochemical rock properties and well integrity of existing wells. All these parameters are cross correlated, and qualitative risk categorization is carried out to determine the robustness of the reservoir for long term CO2 storage. The evaluation of available data indicates less frequent faulting occur only towards the flank with no seismic anomalies associated with them. Some seismic anomalies are observed at shallower levels, however their impact on the reservoir and overburden integrity is assessed to be minimum. There are four shale dominated formations mapped in the overburden section, which will act as potential seals. Estimated fracture pressures for the potential seals ranges between 6200-9280 psia for the deepest seal to 2910-4290 psia for the shallowest. Therefore,it is interpreted that if the post injection reservoir pressure is kept below the initial reservoir pressure of 4480 psia, it would not hold any threat to the caprock integrity.Leakage rate riskalong the existing wells was determined based on well log data. Well integrity check of legacywells helped identify two abandoned wells for rigorous remediation to restore their integrity. The subsurface risk analysis is critical to ascertain the long-term containment of injectedCO2. The integrated subsurface characterization and well integrity analysis approach adopted in this work can be applied to any other field/reservoir to validate its robustness for long-term CO2 injection and storage.

scholarly journals Numerical Simulation and Optimization of CO2 Sequestration in Saline Aquifers

2012 ◽  
Author(s):  
Zheming Zhang ◽  
Ramesh Agarwal
Keyword(s):  
Numerical Simulation ◽  
Co2 Sequestration ◽  
Storage Capacity ◽  
Co2 Storage ◽  
Injection Well ◽  
Co2 Injection ◽  
Great Promise ◽  
Saline Aquifer ◽  
Simulation And Optimization ◽  
Co2 Plume

With recent concerns on CO2 emissions from coal fired electricity generation plants; there has been major emphasis on the development of safe and economical Carbon Dioxide Capture and Sequestration (CCS) technology worldwide. Saline reservoirs are attractive geological sites for CO2 sequestration because of their huge capacity for sequestration. Over the last decade, numerical simulation codes have been developed in U.S, Europe and Japan to determine a priori the CO2 storage capacity of a saline aquifer and provide risk assessment with reasonable confidence before the actual deployment of CO2 sequestration can proceed with enormous investment. In U.S, TOUGH2 numerical simulator has been widely used for this purpose. However at present it does not have the capability to determine optimal parameters such as injection rate, injection pressure, injection depth for vertical and horizontal wells etc. for optimization of the CO2 storage capacity and for minimizing the leakage potential by confining the plume migration. This paper describes the development of a “Genetic Algorithm (GA)” based optimizer for TOUGH2 that can be used by the industry with good confidence to optimize the CO2 storage capacity in a saline aquifer of interest. This new code including the TOUGH2 and the GA optimizer is designated as “GATOUGH2”. It has been validated by conducting simulations of three widely used benchmark problems by the CCS researchers worldwide: (a) Study of CO2 plume evolution and leakage through an abandoned well, (b) Study of enhanced CH4 recovery in combination with CO2 storage in depleted gas reservoirs, and (c) Study of CO2 injection into a heterogeneous geological formation. Our results of these simulations are in excellent agreement with those of other researchers obtained with different codes. The validated code has been employed to optimize the proposed water-alternating-gas (WAG) injection scheme for (a) a vertical CO2 injection well and (b) a horizontal CO2 injection well, for optimizing the CO2 sequestration capacity of an aquifer. These optimized calculations are compared with the brute force nearly optimized results obtained by performing a large number of calculations. These comparisons demonstrate the significant efficiency and accuracy of GATOUGH2 as an optimizer for TOUGH2. This capability holds a great promise in studying a host of other problems in CO2 sequestration such as how to optimally accelerate the capillary trapping, accelerate the dissolution of CO2 in water or brine, and immobilize the CO2 plume.

Integrated Coupled Modelling Study to Assess CO2 Sequestration Potential in a Depleted Gas Field

2021 ◽  
Author(s):  
Ahmad Ismail Azahree ◽  
Farhana Jaafar Azuddin ◽  
Siti Syareena Mohd Ali ◽  
Muhammad Hamzi Yakup ◽  
Mohd Azlan Mustafa ◽  
...  
Keyword(s):  
Storage Capacity ◽  
Co2 Storage ◽  
Coupled Model ◽  
Co2 Injection ◽  
Storage Site ◽  
Coupled Modeling ◽  
Reservoir Properties ◽  
Gas Field ◽  
Sequestration Potential ◽  
Injection Phase

Abstract A depleted gas field is selected as CO2 storage site for future high CO2 content gas field development in Malaysia. The reservoir selected is a carbonate buildup of middle to late Miocene age. This paper describes an integrated modeling approach to evaluate CO2 sequestration potential in depleted carbonate gas reservoir. Integrated dynamic-geochemical and dynamic-geomechanics coupled modeling is required to properly address the risks and uncertainties such as, effect of compaction and subsidence during post-production and injection. The main subsurface uncertainties for assessing the CO2 storage potential are (i) CO2 storage capacity due to higher abandonment pressure (ii) CO2 containment due to geomechanical risks (iii) change in reservoir properties due to reaction of reservoir rock with injected CO2. These uncertainties have been addressed by first building the compositional dynamic model adequately history matched to the production data, and then coupling with geomechanical model and geochemical module during the CO2 injection phase. This is to further study on the trapping mechanisms, caprock integrity, compaction-subsidence implication towards maximum storage capacity and injectivity. The initial standalone dynamic modeling poses few challenges to match the water production in the field due to presence of karsts, extent of a baffle zone between the aquifer and producing zones and uncertainty in the aquifer volume. The overall depletion should be matched, since the field abandonment pressure impacts the CO2 injectivity and storage capacity. A reasonably history matched coupled dynamic-geomechanical model is used as base case for simulating CO2 injection. The dynamic-geomechanical coupling is done with 8 stress steps based on critical pressure changes throughout production and CO2 injection phase. Overburden and reservoir properties has been mapped in Geomechanical grid and was run using two difference constitutive model; Mohr's Coulomb and Modified Cam Clay respectively. The results are then calibrated with real subsidence measurement at platform location. This coupled model has been used to predict the maximum CO2 injection rate of 100 MMscf/d/well and a storage capacity of 1.34 Tscf. The model allows to best design the injection program in terms of well location, target injection zone and surface facilities design. This coupled modeling study is used to mature the field as a viable storage site. The established workflow starting from static model to coupled model to forecasting can be replicated in other similar projects to ensure the subsurface robustness, reduce uncertainty and risk mitigation of the field for CO2 storage site.

Long-term Strategy Optimization of Scale Squeeze Treatment in a Carbonate Reservoir Under CO2-WAG Water-Alternating-Gas Injection

2021 ◽  
Author(s):  
Vahid Azari ◽  
Hydra Rodrigues ◽  
Alina Suieshova ◽  
Oscar Vazquez ◽  
Eric Mackay
Keyword(s):  
Net Present Value ◽  
Co2 Storage ◽  
Gas Injection ◽  
Carbonate Reservoir ◽  
Co2 Injection ◽  
Base Case ◽  
Production Well ◽  
Water Alternating Gas ◽  
Gradient Descent Algorithm

Abstract The objective of this study is to design a series of squeeze treatments for 20 years of production of a Brazilian pre-salt carbonate reservoir analogue, minimizing the cost of scale inhibition strategy. CO2-WAG (Water-Alternating-Gas) injection is implemented in the reservoir to increase oil recovery, but it may also increase the risk of scale deposition. Dissolution of CaCO3 as a consequence of pH decrease during the CO2 injection may result in a higher risk of calcium carbonate precipitation in the production system. The deposits may occur at any location from production bottom-hole to surface facilities. Squeeze treatment is thought to be the most efficient technique to prevent CaCO3 deposition in this reservoir. Therefore, the optimum WAG design for a quarter 5-spot model, with the maximum Net Present Value (NPV) and CO2 storage volume identified from a reservoir optimization process, was considered as the basis for optimizing the squeeze treatment strategy, and the results were compared with those for a base-case waterflooding scenario. Gradient Descent algorithm was used to identify the optimum squeeze lifetime duration for the total lifecycle. The main objective of squeeze strategy optimization is to identify the frequency and lifetime of treatments, resulting in the lowest possible expenditure to achieve water protection over the well's lifecycle. The simulation results for the WAG case showed that the scale window elongates over the last 10 years of production after water breakthrough in the production well. Different squeeze target lifetimes, ranging from 0.5 to 6 million bbl of produced water were considered to optimize the lifetime duration. The optimum squeeze lifetime was identified as being 2 million bbl of protected water, which was implemented for the subsequent squeeze treatments. Based on the water production rate and saturation ratio over time, the optimum chemical deployment plan was calculated. The optimization results showed that seven squeeze treatments were needed to protect the production well in the WAG scenario, while ten treatments were necessary in the waterflooding case, due to the higher water rate in the production window. The novelty of this approach is the ability to optimize a series of squeeze treatment designs for a long-term production period. It adds valuable information at the Front-End Engineering and Design (FEED) stage in a field, where scale control may have a significant impact on the field's economic viability.

scholarly journals CO2 Storage in Low Permeable Carbonate Reservoirs: Permeability and Interfacial Tension (IFT) Changes During CO2 Injection in an Iranian Carbonate Reservoir

2019 ◽  
Vol 64 (4) ◽  
pp. 491-504
Author(s):  
Mohammad Afkhami Karaei ◽  
Bizhan Honarvar ◽  
Amin Azdarpour ◽  
Erfan Mohammadian
Keyword(s):  
Interfacial Tension ◽  
Co2 Sequestration ◽  
Co2 Storage ◽  
Experimental Studies ◽  
Injection Pressure ◽  
Confining Pressure ◽  
Carbonate Reservoir ◽  
Carbonate Reservoirs ◽  
Co2 Injection ◽  
Permeability Alteration

The lack of fundamental experimental studies on low permeable carbonate reservoirs for CO2 sequestration purposes is essential for further application of CO2 sequestration as a highly-anticipated CO2 mitigation method in deep saline aquifers, specifically those with low permeabilities. The core samples were taken from a carbonate reservoir in Iran and the brine composition was based on that of the same formation. The objective of this study is to investigate permeability alteration during CO2 sequestration in the aquifers of a low permeable Iranian carbonate reservoir. Various parameters have been investigated. The effects of different parameters such as injection pressure, confining pressure, and temperature on permeability alteration of the cores was investigated. Moreover, the interfacial tension (IFT) of CO2/brine was also determined at pressures and temperatures up to 7 MPa and 100 °C, respectively. The experimental results showed CO2 solubility and rock dissolution to be the governing mechanism when CO2 was injected into carbonate cores. The permeability measurements showed that permeability increases by increasing injection pressure and decreases by increasing confining pressure and temperature. The IFT measurement results showed that the IFT decreases significantly when there is an increase in pressure and temperature.

Monitoring, Measurement and Verification MMV: A Critical Component in Making the CO2 Sequestration Success

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Debasis Priyadarshan Das ◽  
Parimal Arjun Patil ◽  
Prasanna Chidambaram ◽  
Zoann Low ◽  
...  
Keyword(s):  
Co2 Sequestration ◽  
Fiber Optic Sensor ◽  
Co2 Injection ◽  
Critical Component ◽  
High Co2 ◽  
Plume Migration ◽  
Well Integrity ◽  
Simulation Results ◽  
Co2 Plume ◽  
Gas Fields

Abstract The increasing atmospheric concentration of carbon dioxide (CO2), a greenhouse gas (GHG) is creating environmental imbalance and affecting the climate adversely due to growing industrialization. Global leaders are emphasizing on controlling the production of GHG. However, growing demands of natural gas, industry is embarking on the development of high CO2 contaminant gas fields to meet supply gap. Development and management of contaminated hydrocarbon gas fields add additional dimension of sequestration of CO2 after production and separation in project management. CO2 sequestration is a process for eternity with a possibility of zero-degree failure. Monitoring, measuring and verification (MMV) of injected CO2 volume in sequestration is critical component along with geological site selection, transportation, storage process. The present study discusses all the impacting parameters which makes whole process environment friendly, economically prudent and adhering to national and international regulations. The migration of injected CO2 plume in the reservoir is uncertain and its monitoring is equally challenging. The role of MMV planning is critical in development of high CO2 contaminant fields of offshore Sarawak. It substantiates that injected CO2 in the reservoir is intact and safely stored for hundreds of years after injection and possesses minimum to no risk to HS&E. The deployment of Multi-Fiber Optic Sensor System (M-FOSS) promises a cost-effective solution for monitoring the lateral & vertical migration of CO2 plume by acquiring 4D DAS-VSP (Distributed Acoustic Sensor – Vertical Seismic Profile) survey and for the well integrity by analyzing DAS/DTS (Distributed Temperature Sensor)/DPS (Distributed Pressure Sensor)/DSS (Distributed Strain Sensor) data. Simulation results and injectivity test at laboratory for in-situ CO2 injection has demonstrated the possibility of over 100MMscfd/well injection in aquifer to meet the total CO2 injection of 1.2Bscfd for full field development while maintaining the reservoir integrity. Uncertainty & risk analysis shows possible presence of seismically undistinguished fractures and minor faults, an early breakthrough of injected CO2 cannot be ruled out. The depleted reservoir storage study divulges the containment capacity of identified carbonate reservoirs as well as conformance of potential storage sites. The fault-seal analysis and reservoir integrity studies determine the robustness of the long-term security of the CO2 storage. Injectivity study demonstrates the optimum and maximum possible rates of CO2 injection into these depleted gas reservoirs. VSP simulation results show that a subsurface coverage of 3-4 km2 per well is achievable, which along with simulated CO2 plume extent help to determine the number of wells required to get maximum monitoring coverage for the MMV planning. The deployment of M-FOSS technology is novel and proactive approach to monitor the CO2 plume migration and well integrity. First ever development of MMV Planning for CO2 Sequestration in offshore Sarawak, Malaysia using novel and cutting-edge M-FOSS technology for proactive monitoring of CO2 plume migration and well integrity.

Integrated CO2 Modeling Studies to Assess CO2 Sequestration Prospect in a Depleted Carbonate Gas Reservoir, Malaysia

2021 ◽  
Author(s):  
Mohd Azran A. Jalil ◽  
Sharidah M. Amin ◽  
Siti Syareena M. Ali
Keyword(s):  
Co2 Sequestration ◽  
Co2 Storage ◽  
Injection Pressure ◽  
Injection Rate ◽  
Co2 Injection ◽  
Coupled Modelling ◽  
Compositional Model ◽  
Development Concept ◽  
Modelling Study

Abstract This paper presented an integrated CO2 injection and sequestration modelling study performed on a depleted carbonate gas reservoir, which has been identified as one of potential CO2 sequestration site candidate in conjunction with nearby high CO2 gas fields development and commercialization effort to monetize the fields. 3D compositional modelling, geomechanical and geochemical assessment were conducted to strategize optimum subsurface CO2 injection and sequestration development concept for project execution. Available history matched black oil simulation model was converted into compositional model. Sensitivity analyses on optimum injection rate, number and types of injectors, solubility of CO2 in water, injection locations and impact of hysteresis to plume distribution were investigated. Different types of CO2 trapping mechanisms including hydrodynamic, residual/capillary, solubility and mineral trapping were studied in detailed. Coupled modelling study was performed on base case scenario to assess geomechnical and geochemical risks associated with CO2 injection and sequestration process before-, during- and post- CO2 injection operation to provide assurance for a safe and long-term CO2 sequestration in the field. Available history matched black oil model was successfully converted into compositional model, in which CO2 is treated and can be tracked as a separate component in the reservoir throughout the production and injection processes. Integrating all the results obtained from sensitivities analyses, the proposed optimum subsurface CO2 injection and sequestration development concept for the field is to inject up to 400 MMscf/D of CO2 rate via four injectors. CO2 injection rate is forecasted to sustain more than 3 years from injection start date before declining with time. In terms of CO2 storage capacity, constraining injection pressure up to initial reservoir pressure, maximum CO2 storage capacity is estimated ~65 Million tonnes. Nevertheless, considering maximum allowable CO2 injection pressure estimated from coupled modelling study and operational safety factor, the field is capable to accommodate a total of ~77 Million tonnes of CO2, whereby 73% of total CO2 injected will exists in mobile phase and trapped underneath caprock whilst the other 24% and 3% will be trapped as residual/capillary and dissolved in water respectively. Changes of minerals and porosity were observed from 3D geochemical modelling, however, changes are negligible due to the fact that geochemical reaction is a very slow process. This paper highlights and shares simulation results obtained from CO2 injection and sequestration studies performed on 3D compositional model to generate an optimum subsurface CO2 injection and sequestration development concept for project execution in future. Integration with geomechanical and geochemical modelling studies are crucial to assess site's capability to accommodate CO2 within the geological formation and provide assurance for a safe and long-term CO2 sequestration.

CO2 storage in saline formation: the impacts of reservoir properties and geometry on CO2 trapping mechanisms

2009 ◽  
Vol 49 (1) ◽  
pp. 405
Author(s):  
Diane Labregere ◽  
Norhafiz Marmin ◽  
Suzanne Hurter ◽  
Johan Berge ◽  
Alexander A. Lukyanov
Keyword(s):  
Site Selection ◽  
Co2 Storage ◽  
Separation Distance ◽  
Sensitivity Analyses ◽  
Co2 Injection ◽  
Storage Site ◽  
Residual Saturation ◽  
Worst Case ◽  
Study Results ◽  
Co2 Plume

Effective geological storage of CO2 can be accomplished through a number of trapping mechanisms. Physical trapping is achieved through either CO2 being trapped under a structural closure or CO2 made immobile in the pore space, as residual saturation, by capillary action. Geochemical trapping, which might be regarded as a more secure mode of storage, is achieved through dissolution of CO2 in formation water and precipitation of carbonates. The dissolution rate depends on surface contact and is generally enhanced by greater CO2 plume movement. During site selection, a potential injection well location is commonly evaluated with respect to the proximity to potential leakage features. This paper investigates requirements for separation distance between CO2 injection location and potential leakage features in highly permeable steeply dipping brine reservoir settings. Reservoir models are simulated with a compositional code and sensitivity analyses performed with variations in reservoir permeability, hysteresis effects, and formation dip. Trapping mechanisms, over a timescale of several centuries, are illustrated as key indicators for containment and storage performance. Study results suggest that the amount of CO2 trapped by dissolution and residual saturation is enhanced by a dynamically flowing plume. The simulation results demonstrate that the separation distance requirement typically envisaged in a worst-case reservoir geometry setting is commonly overly conservative, representing opportunity for further optimisation. Numerical simulation is useful in addressing the complex reality of flow dynamics such as hysteresis in footprint prediction. Understanding CO2 plume migration scenarios relative to potential leakage risks, under various key reservoir key properties, is essential in storage containment and capacity assessments for storage site selection and development.

Sign in / Sign up

Export Citation Format

Share Document