scholarly journals Mg-doped and chemo-thermally treated ZnO nanoflowers for ethanol sensing

2021 ◽  
Author(s):  
Santanu Maity ◽  
P.P Sahu ◽  
Tiju Thomas
Keyword(s):  
Gas Sensing ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Applications ◽  
Wide Range ◽  
Doped Zno ◽  
Ethanol Sensing ◽  
Better Than ◽  
Mg Doped

Abstract ZnO nanostructures are promising for a wide range of applications, including gas sensors. Ethanol sensing using ZnO remains unexplored though. In this paper, we report ethanol-sensing using un-doped ZnO nano flowers and Mg doped ZnO nano flowers. These are grown using a rather simple chemo-thermal process, making this a plausibly scalable technology. To study the structural and morphological properties of undoped ZnO and Mg doped ZnO nanoflowers, Raman spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), x-ray diffraction and Field Emission Scanning Electron Microscopy (FESEM) are carried out. Ethanol sensing properties of undoped ZnO and Mg doped ZnO nanoflower devices are investigated toward different ethanol concentration (concentration range of 1–600 ppm at 100°C–200°C). Our findings show that 15% Mg doped ZnO nano flower is better than ZnO nano flower for ethanol gas-sensing applications.

Fabrication of GaN Doped ZnO Nanocrystallines by Laser Ablation

2008 ◽  
Vol 8 (8) ◽  
pp. 4168-4171
Author(s):  
N. Gopalakrishnan ◽  
B. C. Shin ◽  
K. P. Bhuvana ◽  
J. Elanchezhiyan ◽  
T. Balasubramanian
Keyword(s):  
Deep Level ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Ceramic Method ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Doped Zno ◽  
Krf Excimer Laser ◽  
Photoluminescence Studies

Here, we present the fabrication of pure and GaN doped ZnO nanocrystallines on Si(111) substrates by KrF excimer laser. The targets for the ablation have been prepared by conventional ceramic method. The fabricated nanocrystallines have been investigated by X-ray diffraction, photoluminescence and atomic force microscopy. The X-ray diffraction analysis shows that the crystalline size of pure ZnO is 36 nmand it is 41 nmwhile doped with 0.8 mol% of GaN due to best stoichiometry between Zn and O. Photoluminescence studies reveal that intense deep level emissions have been observed for pure ZnO and it has been suppressed for the GaN doped ZnO structures. The images of atomic force microscope show that the rms surface roughness is 27 nm for pure ZnO and the morphology is improved with decrease in rms roughness, 18 nm with fine crystallines while doped with 1 mol% GaN. The improved structural, optical and morphological properties of ZnO nanocrystalline due to GaN dopant have been discussed in detail.

Antibacterial Activity of Nickel -Doped ZnO\MWCNTs hybrid Prepared by Sol-Gel technique

2021 ◽  
Author(s):  
Selma M.H. AL-Jawad ◽  
Zahraa S. Shakir ◽  
Duha S. Ahmed
Keyword(s):  
Antibacterial Activity ◽  
Sol Gel ◽  
Inhibition Zone ◽  
Sem Analysis ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Zno Nps ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Doped Zno

ZnO/MWCNTs hybrid and doped with different concentration of Nickel element prepared by using Sol-gel been technique reported. All samples were prepared and characterized by X-Ray Diffraction Analysis (XRD), Energy Dispersive X-ray Spectroscopy (EDS), Fourier-Transform Infrared Spectroscopy (FTIR), Field-Emission Scanning Electron Microscopy (FE-SEM), and UV-Vis spectroscopy have been identified the structural, optical and morphological properties. X-ray diffraction showed the polycrystalline nature with hexagonal wutzite structure of hybrid and doped with Nickel. The crystalline size of the hybrid nanostructure was increasing from 23.73 nm to 34.59 nm. Besides, the UV-Vis spectroscopy showed a significant decrease in the band gap values from 2.97 eV to 2.01 eV. Whereas the FE-SEM analysis confirm the formation spherical shapes of ZnO NPs deposited on cylindrical tubes representing the MWCNTs. The antibacterial activity reveals that the inhibition zone of Ni doped-ZnO/MWCNTs hybrid was 28.5 mm, 26.5 mm toward E. coli and S. aureus bacteria, respectively.

Study of Bactericidal Properties of Mg-Doped ZnO Nanoparticles

2015 ◽  
Vol 1804 ◽  
pp. 31-36 ◽  
Author(s):  
Melina Perez-Altamar ◽  
Hilary Marrero ◽  
Milton Martínez Julca ◽  
Oscar Perales Perez
Keyword(s):  
Infrared Spectroscopy ◽  
Zno Nanoparticles ◽  
Plate Count ◽  
Exciton Peak ◽  
X Ray Diffraction ◽  
Uv Spectrum ◽  
X Ray ◽  
Bactericidal Properties ◽  
Doped Zno ◽  
Mg Doped

ABSTRACTThe present work focuses on the polyol-mediated synthesis of pure and Mg-doped ZnO nanoparticles. The synthesized samples were characterized via X-ray diffraction, Fourier transformed infrared spectroscopy, ultraviolet visible spectroscopy and photoluminescence techniques. The Standard Plate Count was used to assess the bactericidal properties of the nanoparticles against E. coli at 1000 ppm and 1500 ppm of concentration. The capacity of the Zn-Mg oxides to generate singlet oxygen (SO) species was also evaluated. X-ray diffraction information evidenced the formation of ZnO-wurtzite; no diffraction peaks corresponding to isolated Mg-phases were detected. The average crystallite size of the Zn-Mg oxide nanocrystals was estimated in the 6nm - 7nm range. Infrared spectroscopy measurements confirmed the formation of the oxide with a Metal-Oxygen band centered on 536 cm-1; other bands associated to the functional groups of polyol by product were also observed. The exciton peak of UV spectrum suggests similarity in the particle size with the dopant addition. The effect of particle composition (i.e. doping level) on the corresponding generation of SO and bactericidal capacity is presented and discussed.

Mechanochemical Synthesis of Novel Sensor Materials

2009 ◽  
Vol 1226 ◽  
Author(s):  
Monica Sorescu ◽  
Lucian Diamandescu ◽  
Adelina Tomescu
Keyword(s):  
Ball Milling ◽  
Milling Time ◽  
Gas Sensing ◽  
Mechanochemical Activation ◽  
Magnetic Characteristics ◽  
X Ray Diffraction ◽  
Recoilless Fraction ◽  
X Ray ◽  
Immiscible System ◽  
Sensing Applications

AbstractThe xZnO-(1-x)alpha-Fe2O3 and xZrO2-(1-x)alpha-Fe2O3 nanoparticles systems have been obtained by mechanochemical activation for x=0.1, 0.3 and 0.5 and for ball milling times ranging from 2 to 24 hours. Structural and magnetic characteristics of the zinc and zirconium-doped hematite systems were investigated by X-ray diffraction (XRD), Mössbauer spectroscopy and conductivity measurements. Using the dual absorber method, the recoilless fraction was derived as function of ball milling time for each value of the molar concentration involved. As ZnO is not soluble in hematite in the bulk form, the present study clearly illustrates that the solubility limits of an immiscible system can be extended beyond the limits in the solid state by mechanochemical activation. Moreover, this synthetic route allowed us to reach nanometric particle dimensions, which makes these materials very important for gas sensing applications.

ETHANOL SENSOR OF CdO/Al2O3/CeO2 OBTAINED FROM Ce-DOPED LAYERED DOUBLE HYDROXIDES WITH HIGH RESPONSE AND SELECTIVITY

2013 ◽  
Vol 06 (03) ◽  
pp. 1350035 ◽  
Author(s):  
DONGMEI XU ◽  
MEIYU GUAN ◽  
QINGHONG XU ◽  
YING GUO ◽  
YAO WANG
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Composite Oxides ◽  
Structure Morphology ◽  
Ft Ir ◽  
Ethanol Sensing ◽  
Double Hydroxide ◽  
Double Hydroxides

In this paper, Ce -doped CdAl layered double hydroxide (LDH) was first synthesized and the derivative CdO/Al2O3/CeO2 composite oxide was prepared by calcining Ce -doped CdAl LDH. The structure, morphology and chemical state of the Ce doped CdAl LDH and CdO/Al2O3/CeO2 were also investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), solid state nuclear magnetic resonance (SSNMR), scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The gas sensing properties of CdO/Al2O3/CeO2 to ethanol were further studied and compared with CdO/Al2O3 prepared from CdAl LDH, CeO2 powder as well as the calcined Ce salt. It turns out that CdO/Al2O3/CeO2 sensor shows best performance in ethanol response. Besides, CdO/Al2O3/CeO2 possesses short response/recovery time (12/72 s) as well as remarkable selectivity in ethanol sensing, which means composite oxides prepared from LDH are very promising in gas sensing application.

scholarly journals Characterization of CuO thin films for gas sensing applications

2019 ◽  
Vol 14 (31) ◽  
pp. 1-12
Author(s):  
Jamal M. Rzaij
Keyword(s):  
Room Temperature ◽  
Gas Sensing ◽  
Cupric Oxide ◽  
Laser Pulses ◽  
X Ray Diffraction ◽  
Energy Increase ◽  
Nano Structure ◽  
X Ray ◽  
Sensing Applications

Nanostructural cupric oxide (CuO) films were prepared on Si and glass substrate by pulsed laser deposition technique (PLD) using laser Nd:YAG, using different laser pulses energies from 200 to 600 mJ. The X-ray diffraction pattern (XRD) of the films showed a polycrystalline structure with a monoclinic symmetry and preferred orientation toward (111) plane with nano structure. The crystallite size was increasing with increasing of laser pulse energy. Optical properties was characterized by using UV–vis spectrometer in the wave lengthrange (200-1100) nm at room temperature. The results showed that the transmission spectrum decreases with the laser pulses energy increase. Sensitivity of NO2 gas at different operating temperatures, (50°C, 100°C, 150°C and 200°C) was calculated.

W–Ti–O layers for gas-sensing applications: Structure, morphology, and electrical properties

1998 ◽  
Vol 13 (6) ◽  
pp. 1568-1575 ◽  
Author(s):  
L. Sangaletti ◽  
E. Bontempi ◽  
L. E. Depero ◽  
R. Salari ◽  
M. Zocchi ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Gas Sensing ◽  
Phase Segregation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Applications ◽  
Structure Morphology ◽  
Structural And Electrical Properties ◽  
Kinetics Of ◽  
Structurally Stable

The kinetics of phase transitions and phase segregation induced by annealing temperature on the Ti–W–O gas-sensing layer was studied by x-ray diffraction, Raman spectroscopy, and scanning electron microscopy. The main goal was to identify, on the basis of kinetics studies, structurally stable Ti–WO3 thin film phases and compare their response to polluting gases in order to determine possible correlations between structural and electrical properties of the sensing layers.

Properties of Montmorillonite-Reinforced Thermoplastic Sago Starch Composites

2012 ◽  
Vol 445 ◽  
pp. 469-474 ◽  
Author(s):  
Ahmad Zuraida ◽  
Y. Yusliza ◽  
O. Nurizan ◽  
H. Anuar ◽  
Zahurin Halim ◽  
...  
Keyword(s):  
Morphological Properties ◽  
Wave Number ◽  
Hydroxyl Groups ◽  
Sago Starch ◽  
X Ray Diffraction ◽  
Pressing Method ◽  
X Ray ◽  
Ft Ir ◽  
Thermal Stability Of ◽  
Better Than

In this work, biodegradable polymer was prepared from thermoplastic sago starch (TPSS) plasticized with glycerol. In order to improve the properties of the TPSS, Montmorillonite (MMT), a kind of reinforced additive was used in the preparation of montmorillonite-reinforced thermoplastic sago starch (MTRSS) composites via hot pressing method. The fabricated samples were investigated through X-ray diffractometry, Fourier transform infrared (FT-IR) as well as thermal and morphological properties. FT-IR patterns show that in the MTRSS composites, the C-O groups of sago starch molecules shifted to higher wave number, while the reactive hydroxyl groups of MMT shifted to the lower wavenumber. On the other hand, X-ray diffraction revealed that MMT restrained the crystallization of MTRSS and intercalated in TPSS. Thermogravimetric analysis (TGA) revealed that the thermal stability of MTRSS was better than those of TPSS. In addition, the scanning electron micrograph results show that MMT were uniformly dispersed in the TPSS.

scholarly journals Effect of Growth Temperature and Time on Morphology and Gas Sensitivity of Cu2O/Cu Microstructures

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Ling Wu ◽  
Lun Zhang ◽  
Zhipeng Xun ◽  
Guili Yu ◽  
Liwei Shi
Keyword(s):  
Electron Microscopy ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Spherical Particles ◽  
X Ray Diffraction ◽  
Gas Sensitivity ◽  
X Ray ◽  
Transmission Electron ◽  
Wide Range ◽  
Gas Response

A facile hydrothermal synthesis with CuSO4as the copper source was used to prepare micro/nano-Cu2O. The obtained samples have been characterized by X-ray diffraction, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). With increasing the reaction temperature and time, the final products were successively Cu2O octahedron microcrystals, Cu2O/Cu composite particles, and a wide range of Cu spherical particles. The gas sensitivity of products towards ethanol and acetone gases was studied. The results showed that sensors prepared with Cu2O/Cu composites synthesized at 65°C for 15 min exhibited optimal gas sensitivity. The gas sensing mechanism and the effect of Cu in the enhanced gas response were also elaborated. The excellent gas sensitivity indicates that Cu2O/Cu composites have potential application as gas sensors.

The Preparation of ZnO Gas-Sensing Material by Nucleation-Crystallization Separation Method

2010 ◽  
Vol 152-153 ◽  
pp. 1031-1037
Author(s):  
Xiu Tao Ge ◽  
Jun Hai Wang ◽  
Ding Wang ◽  
Jia Qiang Xu
Keyword(s):  
Gas Sensing ◽  
X Ray Diffraction ◽  
Distribution Method ◽  
Static State ◽  
X Ray ◽  
Sensing Material ◽  
Gas Sensing Properties ◽  
Phase Temperature ◽  
Co Precipitation ◽  
Better Than

The ZnO nanoparticles were synthesized by Nucleation-Crystallization Separation and co-precipitation. The structures and formed phase temperature of the samples were researched by X-ray diffraction (XRD) and DSC -TGA. Gas sensing properties of the samples were measured by a stationary state gas distribution method under static state. The results show that the ZnO prepared from Nucleation-Crystallization Separation has a higher response to 50 ppm ethanol and gasoline than ZnO prepared from co-precipitation. The sensitivity of ZnO prepared from Nucleation-Crystallization Separation to 50 ppm ethanol and gasoline are 34 and 68, which is better than the sensitivity of ZnO prepared from co-precipitation (17 and 28). The good sensing property may be due to the independence of nucleation and crystallization steps, which helps the more uniformity and thermal stability and the larger space utilization of ZnO particles.

Sign in / Sign up

Export Citation Format

Share Document