scholarly journals Seismic Behaviour of Piles in Non-Liquefiable and Liquefiable Soil

2021 ◽  
Author(s):  
Fouad Hussein ◽  
Hesham El Naggar
Keyword(s):  
Finite Element ◽  
Ground Motion ◽  
Numerical Models ◽  
Bending Moment ◽  
Soil Liquefaction ◽  
Shaking Table ◽  
Pile Groups ◽  
Kinematic Interaction ◽  
Inertial Interaction ◽  
Liquefiable Soil

Abstract This paper investigates the nonlinear soil-pile-structure interaction (SPSI) employing three-dimensional (3D) nonlinear finite element models (FEM) verified with the results of large-scale shaking table tests of model pile groups-superstructure systems. The responses of piles in both liquefiable and non-liquefiable soil sites to ground motion with varying intensities were evaluated considering both kinematic and inertial interaction. The calculated piles and soil responses agreed well with the responses measured during the shaking events. The numerical models correctly predicted the different pile deformation modes that were exhibited in the experiments. The finite element analysis (FEA) was then employed to perform a parametric study to evaluate the kinematic and inertial effects on the piles' response, considering different ground motion levels and piles characteristics. It was found that the bending moment of piles in the liquefiable site increases significantly, compared to the non-liquefiable site, due to the loss of lateral support of the liquified soil, and the maximum bending moment occurs at the interface between the liquified and liquefied sand layers. The inertial interaction contributes the most to the bending moments at the pile top and the interface between the top clay and liquefied loose sand layers. For piles with a larger diameter, the bending moment due to kinematic interaction increases significantly, and the bending moment distribution corresponds to short (rigid) pile behaviour. In addition, the piles at the saturated site displace laterally as a rigid body during strong ground motions because the pile base loses the lateral support due to the soil liquefaction. Finally, the kinematic interaction effect becomes more significant for piles with higher elastic modulus.

scholarly journals Seismic Behaviour of Piles in Non-Liquefiable and Liquefiable Soil

2021 ◽  
Author(s):  
Fouad Hussein ◽  
Hesham El Naggar
Keyword(s):  
Ground Motion ◽  
Large Scale ◽  
Numerical Models ◽  
Bending Moment ◽  
Shaking Table ◽  
Pile Groups ◽  
Seismic Behaviour ◽  
Kinematic Interaction ◽  
Inertial Interaction ◽  
Liquefiable Soil

Abstract This paper investigates the nonlinear soil-pile-structure interaction (SPSI) employing three-dimensional (3D) nonlinear finite element (FE) models verified with the results of large-scale shaking table tests of model pile groups-superstructure systems. The responses of piles in both liquefiable and non-liquefiable soil sites to ground motion with varying intensities were evaluated considering both kinematic and inertial interaction. The calculated piles and soil responses agreed well with the responses measured during the shaking events. The numerical models correctly predicted the different pile deformation modes that were exhibited in the experiments. The FEA was then employed to perform a parametric study to evaluate the kinematic and inertial effects on the piles' response considering different ground motion levels and piles characteristics. It was found that the bending moment of piles in the liquefiable site increases significantly, compared to the non-liquefiable site, due to the loss of lateral support of the liquified soil, and the maximum bending moment occurs at the interface between the liquified and non-liquefied sand layers. The inertial interaction contributes the most to the bending moments at the pile top and the interface between the top clay and liquefied loose sand layers. For piles with a larger diameter, the bending moment due to kinematic interaction increases significantly and the bending moment distribution corresponds to short (rigid) pile behaviour. In addition, the piles at the saturated site displace laterally as a rigid body during strong ground motions because the pile base loses the lateral support due to the liquefaction of the bottom dense sand. Finally, the kinematic interaction effect becomes more significant for piles with higher elastic modulus.

Centrifuge Modeling on Seismic Behavior of Pile in Liquefiable Soil Ground

2013 ◽  
Vol 479-480 ◽  
pp. 1139-1143
Author(s):  
Wen Yi Hung ◽  
Chung Jung Lee ◽  
Wen Ya Chung ◽  
Chen Hui Tsai ◽  
Ting Chen ◽  
...  
Keyword(s):  
Seismic Behavior ◽  
Soil Structure ◽  
Lateral Displacement ◽  
Bending Moment ◽  
Soil Liquefaction ◽  
Centrifuge Modeling ◽  
Shaking Table ◽  
Pile Head ◽  
Liquefiable Soil ◽  
Tip Mass

Dramatic failure of pile foundations caused by the soil liquefaction was founded leading to many studies for investigating the seismic behavior of pile. The failures were often accompanied with settlement, lateral displacement and tilting of superstructures. Therefore soil-structure interaction effects must be properly considered in the pile design. Two tests by using the centrifuge shaking table were conducted at an acceleration field of 80 g to investigate the seismic response of piles attached with different tip mass and embedded in liquefied or non-liquefied deposits during shaking. It was found that the maximum bending moment of pile occurs at the depth of 4 m and 5 m for dry sand and saturated sand models, respectively. The more tip mass leads to the more lateral displacement of pile head and the more residual bending moment.

Seismic Response of Pile Groups Improved with Deep Cement mixing Columns in Liquefiable Sand: Shaking Table Tests

2021 ◽  
Author(s):  
Dingwen Zhang ◽  
Anhui Wang ◽  
Xuanming Ding
Keyword(s):  
Seismic Behavior ◽  
Lateral Displacement ◽  
Bending Moment ◽  
Pile Group ◽  
Shaking Table ◽  
Excess Pore Pressure ◽  
Shaking Table Tests ◽  
Pile Groups ◽  
Acceleration Response ◽  
Table Model

A series of shaking table model tests were performed to examine the effects of deep cement mixing (DCM) columns with different reinforcement depths on the seismic behavior of a pile group in liquefiable sand. Due to the DCM column reinforcement, the fundamental natural frequency of the model ground increases noticeably. The excess pore pressure of soils reduces with the increase of reinforcement depths of the DCM columns. Before liquefaction, the acceleration response of soils in the improved cases is obviously lower than that in the unimproved case, but the acceleration attenuation is greater after liquefaction in the unimproved case. Moreover, the lateral displacement of the superstructure, the settlement of the raft, and the bending moment of the piles in the improved cases are significantly reduced compared to those in the unimproved case, and the reduction ratios rise with the increase of reinforcement depth of the DCM columns. However, reinforcement by the DCM columns may result in the variation of the location of the maximum moment that occurs in the pile.

scholarly journals Finite element analysis of dovetail joint made with the use of CNC technology

2010 ◽  
Vol 58 (5) ◽  
pp. 321-328 ◽  
Author(s):  
Václav Sebera ◽  
Milan Šimek
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Models ◽  
Experimental Testing ◽  
Joint Stiffness ◽  
Bending Moment ◽  
Parametric Models ◽  
Cnc Machine ◽  
Element Analysis ◽  
Bending Load

The objective of the paper is the parametrization and the finite element analysis of mechanical pro­per­ties of a through dovetail joint made with the use of a specific procedure by a 3-axis CNC machine. This corner joint was used for the simulation of the bending load of the joint in the angle plane – by compression, i.e. by pressing the joint together. The deformation fields, the stress distribution, the stiffness and the bending moment of the joints were evaluated. The finite element system ANSYS was used to create two parametric numerical models of the joint. The first one represents an ideal­ly stiff joint – both joint parts have been glued together. The second model includes the contact between the joined parts. This numerical model was used to monitor the response of the joint stiffness to the change of the static friction coefficient. The results of both models were compared both with each other and with similar analyses conducted within the research into ready-to-assemble furniture joints. The results can be employed in the designing of more complex furniture products with higher demands concerning stiffness characteristics, such as furniture for sitting. However, this assumption depends on the correction of the created parametric models by experimental testing.

scholarly journals Development of Simulation Based p-Multipliers for Laterally Loaded Pile Groups in Granular Soil Using 3D Nonlinear Finite Element Model

2020 ◽  
Vol 11 (1) ◽  
pp. 26
Author(s):  
Muhammad Bilal Adeel ◽  
Muhammad Asad Jan ◽  
Muhammad Aaqib ◽  
Duhee Park
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Design Guidelines ◽  
American Petroleum Institute ◽  
Winkler Foundation ◽  
Group Effect ◽  
Pile Groups ◽  
Element Analysis ◽  
Laterally Loaded Pile ◽  
Laterally Loaded

The behavior of laterally loaded pile groups is usually accessed by beam-on-nonlinear-Winkler-foundation (BNWF) approach employing various forms of empirically derived p-y curves and p-multipliers. Averaged p-multiplier for a particular pile group is termed as the group effect parameter. In practice, the p-y curve presented by the American Petroleum Institute (API) is most often utilized for piles in granular soils, although its shortcomings are recognized. In this study, we performed 3D finite element analysis to develop p-multipliers and group effect parameters for 3 × 3 to 5 × 5 vertically squared pile groups. The effect of the ratio of spacing to pile diameter (S/D), number of group piles, varying friction angle (φ), and pile fixity conditions on p-multipliers and group effect parameters are evaluated and quantified. Based on the simulation outcomes, a new functional form to calculate p-multipliers is proposed for pile groups. Extensive comparisons with the experimental measurements reveal that the calculated p-multipliers and group effect parameters are within the recorded range. Comparisons with two design guidelines which do not account for the pile fixity condition demonstrate that they overestimate the p-multipliers for fixed-head condition.

scholarly journals Sustainable Measures for Protection of Structures Against Earthquake Induced Liquefaction

2021 ◽  
Author(s):  
Gopal S. P. Madabhushi ◽  
Samy Garcia-Torres
Keyword(s):  
Soil Liquefaction ◽  
Excess Pore Pressure ◽  
Economic Losses ◽  
Element Analysis ◽  
Centrifuge Testing ◽  
Centrifuge Tests ◽  
Liquefiable Soil ◽  
Recent Earthquakes ◽  
Excess Pore Pressures ◽  
Excess Pore

AbstractSoil liquefaction can cause excessive damage to structures as witnessed in many recent earthquakes. The damage to small/medium-sized buildings can lead to excessive death toll and economic losses due to the sheer number of such buildings. Economic and sustainable methods to mitigate liquefaction damage to such buildings are therefore required. In this paper, the use of rubble brick as a material to construct earthquake drains is proposed. The efficacy of these drains to mitigate liquefaction effects was investigated, for the first time to include the effects of the foundations of a structure by using dynamic centrifuge testing. It will be shown that performance of the foundation in terms of its settlement was improved by the rubble brick drains by directly comparing them to the foundation on unimproved, liquefiable ground. The dynamic response in terms of horizontal accelerations and rotations will be compared. The dynamic centrifuge tests also yielded valuable information with regard to the excess pore pressure variation below the foundations both spatially and temporally. Differences of excess pore pressures between the improved and unimproved ground will be compared. Finally, a simplified 3D finite element analysis will be introduced that will be shown to satisfactorily capture the settlement characteristics of the foundation located on liquefiable soil with earthquake drains.

Analysis of Pipe-Soil Interaction for a Miniature Pipejacking

2006 ◽  
Vol 22 (3) ◽  
pp. 213-220 ◽  
Author(s):  
K. J. Shou ◽  
F. W. Chang
Keyword(s):  
Finite Element ◽  
Failure Mechanism ◽  
Physical Modeling ◽  
Driving Force ◽  
Numerical Models ◽  
Surface Subsidence ◽  
Finite Element Software

AbstractIn this study, physical and numerical models were used to analyze pipe-soil interaction during pipejacking work. After calibrating with the physical modeling results, the finite element software ABAQUS [1] was used to study the pipejacking related behavior, such as surface subsidence, failure mechanism, pipe-soil interaction, etc. The results show that the driving force in the tunnelling face is very important and critical for pipejacking. Surface subsidence is mainly due to the lack of driving force, however, excessive driving force could cause the unfavorable surface heaving problem. It also suggests that the depth of the pipe is critical to determine a proper driving force to stabilize the tunnelling face.

COMPARATIVE ANALYSIS FOR THREE FIXTURES OF PAUWELLS-II BY THE BIOMECHANICAL FINITE ELEMENT METHOD

2019 ◽  
Vol 20 (01) ◽  
pp. 1950079
Author(s):  
MATTHEW JIAN-QIAO PENG ◽  
HONGWEN XU ◽  
HAI-YAN CHEN ◽  
XIANGYANG JU ◽  
YONG HU ◽  
...  
Keyword(s):  
Finite Element ◽  
Numerical Models ◽  
Femoral Shaft ◽  
3D Models ◽  
Procedure Time ◽  
Stable Fixation ◽  
Secondary Fracture ◽  
Solid Models ◽  
Acute Correction ◽  
Hip Screw

Little is known about why and how biomechanics govern the hypothesis that three-Lag-Screw (3LS) fixation is a preferred therapeutic technique. A series models of surgical internal-fixation for femoral neck fractures of Pauwells-II will be constructed by an innovative approach of finite element so as to determine the most stable fixation by comparison of their biomechanical performance. Seventeen sets of CT scanned femora were imported onto Mimics extracting 3D models; these specimens were transferred to Geomagic Studio for a simulative osteotomy and kyrtograph; then, they underwent UG to fit simulative solid models; three sorts of internal fixators were expressed virtually by Pro-Engineer. Processed by Hypermesh, all compartments were assembled onto three systems actually as “Dynamic hip screw (DHS), 3LS and DHS+LS”. Eventually, numerical models of Finite Elemental Analysis (FEA) were exported to AnSys for solution. Three models for fixtures of Pauwells-II were established, validated and analyzed with the following findings: Femoral-shaft stress for [Formula: see text](3LS) is the least; Internal-fixator stress (MPa) for [Formula: see text]; Integral stress (MPa) for [Formula: see text]; displacement of femoral head (mm) for a[Formula: see text](DHS+LS) = 0.735; displacement of femoral shaft (mm) for [Formula: see text]; and displacement of fixators for [Formula: see text]. Mechanical comparisons for other femoral parks are insignificantly different, and these data can be abstracted as follows: the stress of 3LS-system was checked to be the least, and an interfragmentary displacement of DHS+LS assemblages was assessed to be the least”. A 3LS-system should be recommended to clinically optimize a Pauwells-II facture; if treated by this therapeutic fixation, breakage of fixators or secondary fracture is supposed to occur rarely. The strength of this study is that it was performed by a computer-aided simulation, allowing for design of a preoperative strategy that could provide acute correction and decrease procedure time, without harming to humans or animals.

Finite Element Modeling of Self-Loosening of Bolted Joints

2004 ◽  
Author(s):  
Ming Zhang ◽  
Yanyao Jiang ◽  
Chu-Hwa Lee
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Bending Moment ◽  
Shear Loading ◽  
Transverse Load ◽  
Fe Model ◽  
Bolted Joint ◽  
Cyclic Bending ◽  
Second Stage ◽  
Cyclic Bending Moment

A three-dimensional finite element (FE) model with the consideration of the helix angle of the threads was developed to simulate the second stage self-loosening of a bolted joint. The second stage self-loosening refers to the graduate reduction in clamping force due to the back-off of the nut. The simulations were conducted for two plates jointed by a bolt and a nut and the joint was subjected to transverse or shear loading. An M12×1.75 bolt was used. The application of the preload was simulated by using an orthogonal temperature expansion method. FE simulations were conducted for several loading conditions with different preloads and relative displacements between the two clamped plates. It was found that due to the application of the cyclic transverse load, micro-slip occurred between the contacting surfaces of the engaged threads of the bolt and the nut. In addition, a cyclic bending moment was introduced on the bolted joint. The cyclic bending moment resulted in an oscillation of the contact pressure on the contacting surfaces of the engaged threads. The micro-slip between the engaged threads and the variation of the contact pressure were identified to be the major mechanisms responsible for the self-loosening of a bolted joint. Simplified finite element models were developed that confirmed the mechanisms discovered. The major self-loosening behavior of a bolted joint can be properly reproduced with the FE model developed. The results obtained agree quantitatively with the experimental observations.

Character Analysis of Balance and Imbalance of Varying Rigidity of Rigid Pile Composite Foundation under Seismic Load

2014 ◽  
Vol 1065-1069 ◽  
pp. 19-22
Author(s):  
Zhen Feng Wang ◽  
Ke Sheng Ma
Keyword(s):  
Finite Element ◽  
Bending Moment ◽  
Horizontal Displacement ◽  
Element Model ◽  
Composite Foundation ◽  
Seismic Load ◽  
Seismic Loads ◽  
Element Analysis ◽  
Rigid Pile ◽  
Rigid Pile Composite Foundation

Based on ABAQUS finite element analysis software simulation, the finite element model for dynamic analysis of rigid pile composite foundation and superstructure interaction system is established, which selects the two kinds of models, by simulating the soil dynamic constitutive model, selecting appropriate artificial boundary.The influence of rigid pile composite foundation on balance and imbalance of varying rigidity is analyzed under seismic loads. The result shows that the maximum bending moment and the horizontal displacement of the long pile is much greater than that of the short pile under seismic loads, the long pile of bending moment is larger in the position of stiffness change. By constrast, under the same economic condition, the aseismic performance of of rigid pile composite foundation on balance of varying rigidity is better than that of rigid pile composite foundation on imbalance of varying rigidity.

Sign in / Sign up

Export Citation Format

Share Document