Study on Overlying Strata Movement and Surface Subsidence of Coal Workfaces with Karst Aquifer Water

The overlying strata layers of coal workfaces with karst aquifer water normally causes serious safety problems due to the precipitation, drainage and water inrush, such as a wide range and long term of surface subsidence. In this study, by taking 10,301 working faces of the Daojiao coal mine in Guizhou Province as the engineering background, the numerical model of water-bearing strata with fluid-solid coupling was established by using UDEC to illustrate the laws of overlying strata movement and surface subsidence. A theory model was proposed to calculate the surface settlement caused by the drainage of aquifer based on the principle of effective stress modified by the Biot coefficient αb. The results showed that the corresponding maximum value (0.72 m) and the range of the surface subsidence with the occurrence of karst aquifer water were larger than that of the overlying strata without karst aquifer water (e.g., the maximum value of surface subsidence with 0.1 m). Moreover, the surface subsidence caused by the drainage of aquifer accounted for 17.8% of the total surface subsidence caused by coal mining. According to the field monitoring of surface subsidence in 10,301 working faces, the maximum value was 0.74 m, which was highly consistent with the results of numerical simulation and theoretical analysis. It verified the accuracy and reliability of the numerical model and the theory model in this study.

Roof Subsidence and Movement Law of Composite Strata Mining: Insights from Physical and Numerical Modeling

Sinking and horizontal movements are necessary parameters for assessing the potential impacts of surface subsidence in mining activities. Based on similarity criteria, the surface subsidence mechanism was studied using a physical model composed of similar materials such as sand, cement, and gypsum. With constant field geological parameters maintained in two angles of a coal seam, models of roof subsidence of composite rock were compared for different mining configurations. In accordance with observations from the physical model, it was concluded that subsidence and horizontal movement of strata near to and far from the coal seams were different and divided into five zones. The zone above a mined-out area underwent greater total subsidence compared to unexploited regions on both sides. Correlations between a subsidence curve and the height of a caving zone and the mining dip angle were obtained and verified from numerical model results. According to the roof’s position relative to the goaf, the area above the goaf of the composite rock layer was divided into three regions: a curving zone, a water-conducting fracture zone, and a falling zone, to which the subsidence and movement characteristics of each area could be proposed. Compared with the subsidence and movement characteristics observed from the physical and numerical model, the acquisition of subsidence characteristics and parameters in different areas can provide an idea for improvement, innovation or proposal of a theoretical formula for subsidence prediction of composite rock formations.

Field Study on the Law of Surface Subsidence in the High-Intensity Fully Mechanized Caving Mining Working Face with Shallow Thick Bedrock and Thin Epipedon in Hilly Areas

Shallow and thick coal seams occur extensively in hilly areas in Shanxi Province and Shaanxi Province, China. The surface damage and landslides caused by shallow fully mechanized caving mining have a very serious impact on the environment. To provide a theoretical and reference foundation for mine environmental protection in hilly settings, a research on surface movement of the high-intensity fully mechanized caving mining working face with shallow thick bedrock and thin epipedon (HIFMCMWFSTBTE) is urgently needed. In this study, using the P2 working face of a mine as the research object, three surface subsidence observation lines were arranged in this working face to analyze the dynamic change characteristics of surface subsidence. Besides, the law of surface movement, mining sufficiency, fracture development and distribution characteristics, subsidence speed, and surface movement duration of HIFMCMWFSTBTE in hilly areas were comparatively studied. The research results reveal that the upper part of the slope slides towards the downhill direction under the action of tensile stress or push stress. As a result, the range of the horizontal movement towards the downhill direction of the slope and the range of surface movement both increase, and the movement angle and boundary angle both decrease compared with the plain. HIFMCMWFSTBTE is prone to serious sudden discontinuous damage. Fractures on the gully region surface develop along the contour, forming a crisscross fracture network, and the fractures are not easy to close after being generated. HIFMCMWFSTBTE in hilly areas can achieve full mining more easily than those of other geological conditions. According to the field measurement, critical full mining can be achieved in P2 working face when the ratio of mining width to mining depth is 1.07. The surface movement duration of HIFMCMWFSTBTE in hilly areas is relatively short. Considerable subsidence will occur in the active stage, and the surface subsidence is sudden and violent. The measured surface stabilization time of the P2 working face is only 20% of the calculated value in the Specification for Coal Pillar Reservation and Coal Mining under Buildings, Water Bodies, Railways, and Main Shafts (hereinafter referred to as the Specification), indicating that the specification's empirical formula is inapplicable to the calculation of surface stabilization time of the P2 working face.

Thermokarst Landscape Development Detected by Multiple-Geospatial Data in Churapcha, Eastern Siberia

Thermokarst is a typical process that indicates widespread permafrost degradation in yedoma landscapes. The Lena-Aldan interfluvial area in Central Yakutia in eastern Siberia is now facing extensive landscape changes with surface subsidence due to thermokarst development during the past few decades. To clarify the spatial extent and rate of subsidence, multiple spatial datasets, including GIS and remote sensing observations, were used to analyze the Churapcha rural locality, which has a typical yedoma landscape in Central Yakutia. Land cover classification maps for 1945 and 2009 provide basic information on anthropogenic disturbance to the natural landscape of boreal forest and dry grassland. Interferometric synthetic aperture radar (InSAR) with ALOS-2/PALSAR-2 data revealed activated surface subsidence of 2 cm/yr in the disturbed area, comprising mainly abandoned agricultural fields. Remote sensing with an unmanned aerial system also provided high-resolution information on polygonal relief formed by thermokarst development at a disused airfield where InSAR analysis exhibited extensive subsidence. It is worth noting that some historically deforested areas have likely recovered to the original landscape without further thermokarst development. Spatial information on historical land-use change is helpful because most areas with thermokarst development correspond to locations where land was used by humans in the past. Going forward, the integrated analysis of geospatial information will be essential for assessing permafrost degradation.

Field Measurement and Study on Overburden Fracture and Surface Subsidence Law of Solid Filling Mining under Buildings

In order to predict the surface subsidence scientifically in solid filling mining, it is necessary to establish a complete subsidence prediction model and parameter system according to the evolution law of overburden structure and strata movement characteristics. Mine pressure monitoring and borehole peeping show that the overburden in solid filling mining is mainly a bending zone with relatively complete layered structure, and the overburden only develops a certain height of fault zone near the roof, without collapse. The results show that the surface subsidence pattern of solid filling mining can still be described by probability integral model, and the parameter system of the surface subsidence prediction model based on “equivalent mining height” is further discussed. Finally, the prediction model of surface subsidence established in this paper is applied to an engineering example, and good results are achieved.

A Vertical Joint Spacing Calculation Method for UDEC Modeling of Large-Scale Strata and Its Influence on Mining-Induced Surface Subsidence

While universal discrete element code (UDEC) is widely used for understanding the mechanism of large-scale strata movement and the effects of mining subsidence on the environment, the fundamental knowledge of how to set vertical joint spacing (VJS) in UDEC is still not fully understood. To address the knowledge gap, we first present a novel VJS calculation method, then conduct UDEC experiments, and finally compare the predictions of UDEC models with field subsidence observation. The results suggest the following: (1) when compared to the conventional VJS setting (1× to 3× bed thickness), the maximum surface subsidence (MSS) prediction via UDEC models based on our proposed VJS setting method is closer to field observation; (2) a smaller but varying VJS setting can also have the effect of a larger VJS setting; and (3) with the increase in VJS, MSS first drops, then rises, and reaches the minimum when VJS is set at approximately 7× bed thickness. This paper provides an explanation of the VJS setting in UDEC and establishes a bridge between the KS theory and VJS, which is helpful for the sustainable development of such an UDEC modeling strategy and for a better understanding of the influences of mining subsidence on the environment in mining-affected areas.