scholarly journals Optimization of total trihalomethanes' (TTHMs) and their precursors' removal by granulated activated carbon (GAC) and sand dual media by response surface methodology (RSM)

2015 ◽  
Vol 16 (3) ◽  
pp. 783-793 ◽  
Author(s):  
Sajida Rasheed ◽  
Luiza. C. Campos ◽  
Jong. K. Kim ◽  
Qizhi Zhou ◽  
Imran Hashmi
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Quadratic Model ◽  
Residual Chlorine ◽  
Sand Column ◽  
Toc Removal ◽  
Chlorine Removal ◽  
Full Factorial ◽  
Granulated Activated Carbon

A response surface methodology (RSM) applying central composite design with rotatable full factorial (14 non-center and six center points) was used to discern the effect of granular activated carbon (GAC), sand and pH on total trihalomethanes (TTHMs) and humic acid (HA) removal from drinking water. Results showed efficient TTHMs and HA removal by GAC while a sand column showed little effect for TTHMs but was significant for total organic carbon (TOC) removal. With GAC and a sand column of 4 cm, a pH increase from 6 to 8 caused an increase in TTHM removal from 79.8 to 83.6% while a decrease in HA removal from 26.6 to 6.6% was observed. An increase in GAC column depth from 10 to 20 cm caused a slight increase in TTHM removal from 99.4 to 99.7%, while TOC removal was increased from an average of 38.85% to 57.4% removal. The developed quadratic model for TTHM removal (p = 0.048) and linear model for TOC removal (p = 0.039) were significant. GAC column depth (p < 0.0117) and column depth2 (p < 0.039) were the most significant factors. A 98% TTHMs, 30%TOC and 51% residual chlorine removal were optimized at 9 cm GAC and 4 cm sand column depth at pH 8 with desirability factor (D) 0.64.

Detoxification of photo-catalytically treated 2-chlorophenol: optimization through response surface methodology

2017 ◽  
Vol 76 (2) ◽  
pp. 323-336 ◽  
Author(s):  
Muhammad Z. Ahamd ◽  
S. Ehtisham-ul-Haque ◽  
Numrah Nisar ◽  
Khizar Qureshi ◽  
Abdul Ghaffar ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Uv Irradiation ◽  
Irradiation Time ◽  
Oxygen Demand ◽  
Quadratic Model ◽  
Coefficient Of Determination ◽  
Process Variables ◽  
Treatment Efficiency ◽  
Toc Removal

The present study was conducted to degrade and detoxify 2-chlorophenol (2-CP) under UV irradiation in the presence of titanium dioxide (TiO2) and hydrogen peroxide (H2O2). The treatment efficiency was evaluated on the basis of degradation and cytotoxicity reduction as well as biochemical oxygen demand (BOD), chemical oxygen demand (COD) and total organic carbon (TOC) removal. The process variables such as TiO2, pH, UV irradiation time and H2O2 were optimized. Central composite design in combination with response surface methodology was employed to optimize the process variables. A quadratic model was proposed to predict the treatment efficiency and analysis of variance was used to determine the significance of the variables. The correlation between the experimental and predicted degradation was confirmed by the F and P values (<0.05). The coefficient of determination (R2 = 0.99) were high enough to support the validity of developed model. At optimized conditions, up to 92% degradation of 2-CP was achieved with 3.5 × 10−4 s−1 rate constant. Significant reductions in BOD, COD and TOC values were also achieved. Cytotoxicity was evaluated using bioassays and it was observed that UV/TiO2/H2O2 reduced the cytotoxicity considerably. It is concluded that UV/TiO2/H2O2 could possibly be used to detoxify 2-CP in industrial wastewater.

scholarly journals OPTIMIZATION OF ACTIVATED CARBON SYNTHESIS USING RESPONSE SURFACE METHODOLOGY TO ENHANCE H2S REMOVAL FROM REFINERY WASTEWATER

1970 ◽  
Vol 1 (1) ◽  
pp. 1-17
Author(s):  
Omar Abed Habeeb ◽  
Ramesh Kanthasamy ◽  
Gomaa A. M. Ali ◽  
Rosli Mohd Yunus
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Chemical Activation ◽  
Synthetic Wastewater ◽  
Quadratic Model ◽  
Activation Time ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Influential Variable

The main point of this study is to investigate the optimal conditions for preparation of activated carbon from wood sawdust (ACWSD) for removal of hydrogen sulfide (H2S) from wastewater. The response surface methodology (RSM) was employed to prepare the ACWSD by chemical activation with potassium hydroxide (KOH). The threepreparation  variables impact of activation temperature (724 – 1000 °C), KOH: precursor (wt%) impregnation ratio (IR) (2:1 – 4:1) and activation time (60 – 120 min) on removal efficiency (RE, %) of H2S and activated carbon yield (ACY, %) were investigated. The preparation parameters were correlated by developing a quadratic model depend on the central composite design (CCD) to the two responses. The analysis of variance (ANOVA) was identified the most influential variable on each experimental design responses. The results showed that the temperature of 854 °C, chemical impregnation ratio of 2.95 wt% and activation time of 80 min were the optimum conditions for preparation of ACWSD with responses of RE and ACY of 72.88 % and 31.89 %, respectively. It is concluded that the ACWSD was appeared to be a favorable substance for removal of dissolved H2S from synthetic wastewater.

scholarly journals Response Surface Methodology: Photocatalytic Degradation Kinetics of Basic Blue 41 Dye Using Activated Carbon with TiO2

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 1068
Author(s):  
Emmanuel Kweinor Tetteh ◽  
Elorm Obotey Ezugbe ◽  
Dennis Asante-Sackey ◽  
Edward Kwaku Armah ◽  
Sudesh Rathilal
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Reaction Time ◽  
Photocatalytic Degradation ◽  
Response Surface ◽  
Quadratic Model ◽  
Phase Identification ◽  
Optimization Approach ◽  
Turbidity Removal ◽  
Catalyst Load

Water decontamination still remains a major challenge to some developing countries not having centralized wastewater systems. Therefore, this study presents the optimization of photocatalytic degradation of Basic Blue 41 dye in an aqueous medium by an activated carbon (AC)-TiO2 photocatalyst under UV irradiation. The mesoporous AC-TiO2 synthesized by a sonication method was characterized by X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy for crystal phase identification and molecular bond structures, respectively. The efficiency of the AC-TiO2 was evaluated as a function of three input variables viz. catalyst load (2–4 g), reaction time (15–45 min) and pH (6–9) by using Box-Behnken design (BBD) adapted from response surface methodology. Using color and turbidity removal as responses, a 17 run experiment matrix was generated by the BBD to investigate the interaction effects of the three aforementioned input factors. From the results, a reduced quadratic model was generated, which showed good predictability of results agreeable to the experimental data. The analysis of variance (ANOVA), signposted the selected models for color and turbidity, was highly significant (p < 0.05) with coefficients of determination (R2) values of 0.972 and 0.988, respectively. The catalyst load was found as the most significant factor with a high antagonistic impact on the process, whereas the interactive effect of reaction time and pH affected the process positively. At optimal conditions of catalyst load (2.6 g), reaction time (45 min), and pH (6); the desirability of 96% was obtained by a numerical optimization approach representing turbidity removal of 93% and color of 96%.

Adsorption of Cu(II) Ions on Areca Catechu Stem-Based Activated Carbon: Optimization Using Response Surface Methodology

2019 ◽  
Vol 12 (2) ◽  
pp. 123
Author(s):  
Abrar Muslim ◽  
Marwan Marwan ◽  
Ramli Saifullah ◽  
Muhammad Yahya Azwar ◽  
Darmadi Darmadi ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Areca Catechu

EXTRACTION OPTIMIZATION AND ANTIOXIDANT ACTIVITY OF PHENOLIC COMPOUNDS FROM AVOCADO PEEL

2019 ◽  
pp. 49-59
Author(s):  
Nu Linh Giang Ton ◽  
Thi Hoai Nguyen ◽  
Quoc Hung Vo
Keyword(s):  
Antioxidant Activity ◽  
Response Surface Methodology ◽  
Antioxidant Capacity ◽  
Response Surface ◽  
Total Antioxidant Capacity ◽  
Total Phenolic Content ◽  
Phenolic Content ◽  
Quadratic Model ◽  
Total Phenolic ◽  
Total Antioxidant

Avocado peel has been considered as a potential source of natural antioxidants in which phenolics are among the most important compounds. Therefore, this study aims to optimize the extraction process of phenolics using response surface methodology and evaluate the corresponding antioxidant activity. From the quadratic model, the optimal condition was determined including the ethanol concentration 54.55% (v/v), the solvent/solute ratio 71.82/1 (mL/g), temperature 53.03 oC and extraction time 99.09 min. The total phenolic content and the total antioxidant capacity at this condition with minor modifications were 26,74 ± 0,04 (mg GAE/g DW) and 188.06 ± 1.41 (mg AAE/g DW), respectively. The significant correlation between total phenolic content and total antioxidant capacity was also confirmed. Key words: response surface methodology, central composite rotatable design, total phenolic content, total antioxidant capacity, avocado peel

scholarly journals Optimization of Lignin Extraction Variables by Response Surface Methodology from Pine Saw Dust, and Quantification of Major Structural Units in Isolated Lignin Fraction

2021 ◽  
Vol 11 (4) ◽  
pp. 1739
Author(s):  
Muhammad Ajaz Ahmed ◽  
Jae Hoon Lee ◽  
Joon Weon Choi
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Quantum Coherence ◽  
Resonance Spectrum ◽  
Quadratic Model ◽  
Molecular Weights ◽  
Solids Loading ◽  
A Value ◽  
Lignin Extraction ◽  
Lignin Fraction

A synergistic combination of dioxane, acetic acid, and HCl was investigated for lignin extraction from pine wood biomass. After initial screening of reagent combination, response surface methodology (RSM) was used to optimize the lignin yield with respect to the variables of time 24–72 h, solids loading 5–15%, and catalyst dose 5–15 mL. A quadratic model predicted 8.33% of the lignin yield, and it was further confirmed experimentally and through the analysis of variance (ANOVA). Lignin at optimum combination exhibited features in terms of derivatization followed by reductive cleavage (DFRC) with a value of (305 µmol/gm), average molecular weights of 4358 and polydispersity of 1.65, and 2D heteronuclear single quantum coherence nuclear magnetic resonance spectrum (2D-HSQC NMR) analysis showing relative β-O-4 linkages (37.80%). From here it can be suggested that this fractionation can be one option for high quality lignin extraction from lignocellulosic biomass.

scholarly journals Optimizing Adsorption of 17α-Ethinylestradiol from Water by Magnetic MXene Using Response Surface Methodology and Adsorption Kinetics, Isotherm, and Thermodynamics Studies

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3150
Author(s):  
Mengwei Xu ◽  
Chao Huang ◽  
Jing Lu ◽  
Zihan Wu ◽  
Xianxin Zhu ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Quadratic Model ◽  
Adsorption Efficiency ◽  
Process Variables ◽  
Adsorption Time ◽  
Initial Concentration ◽  
Independent Variables ◽  
The Impact ◽  
Adsorbent Dose

Magnetic MXene composite Fe3O4@Ti3C2 was successfully prepared and employed as 17α-ethinylestradiol (EE2) adsorbent from water solution. The response surface methodology was employed to investigate the interactive effects of adsorption parameters (adsorption time, pH of the solution, initial concentration, and the adsorbent dose) and optimize these parameters for obtaining maximum adsorption efficiency of EE2. The significance of independent variables and their interactions were tested by the analysis of variance (ANOVA) and t-test statistics. Optimization of the process variables for maximum adsorption of EE2 by Fe3O4@Ti3C2 was performed using the quadratic model. The model predicted maximum adsorption of 97.08% under the optimum conditions of the independent variables (adsorption time 6.7 h, pH of the solution 6.4, initial EE2 concentration 0.98 mg L−1, and the adsorbent dose 88.9 mg L−1) was very close to the experimental value (95.34%). pH showed the highest level of significance with the percent contribution (63.86%) as compared to other factors. The interactive influences of pH and initial concentration on EE2 adsorption efficiency were significant (p < 0.05). The goodness of fit of the model was checked by the coefficient of determination (R2) between the experimental and predicted values of the response variable. The response surface methodology successfully reflects the impact of various factors and optimized the process variables for EE2 adsorption. The kinetic adsorption data for EE2 fitted well with a pseudo-second-order model, while the equilibrium data followed Langmuir isotherms. Thermodynamic analysis indicated that the adsorption was a spontaneous and endothermic process. Therefore, Fe3O4@Ti3C2 composite present the outstanding capacity to be employed in the remediation of EE2 contaminated wastewaters.

Analysis of faults in rotor-bearing system using three-level full factorial design and response surface methodology

2021 ◽  
pp. 095745652110307
Author(s):  
Hara P Mishra ◽  
Arun Jalan
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Fault Analysis ◽  
Vibration Response ◽  
Effect Analysis ◽  
Outer Race ◽  
Surface Plot ◽  
Rotor Bearing ◽  
Full Factorial ◽  
Bearing System

This article presents the experimental and statistical methodology for localized fault analysis in the rotor-bearing system. These defects on outer race, on inner race, and on a combination of ball and outer race are considered. In this study speed, load and defects were considered as the essential process variables to understand their significance and effects on vibration response for the rotor-bearing system. Three factors at three levels were considered for experimentation, and the experiment was designed for L27 based on design of experiments (DOE) methodology. From the experiments, the vibration response results are recorded in terms of root mean square value for the analysis. Response surface methodology (RSM) is used for identifying the interaction effect of varying process parameters upon the response of vibrations by response surface plot. The rotor-bearing test setup is used for experimentation and is analyzed by using DOE. This study establishes the prediction of fault in the rotor-bearing system in combined parametric effect analysis and its influence with DOE and RSM.

Sign in / Sign up

Export Citation Format

Share Document