Granular activated algae for wastewater treatment

2015 ◽  
Vol 71 (6) ◽  
pp. 832-839 ◽  
Author(s):  
O. Tiron ◽  
C. Bumbac ◽  
I. V. Patroescu ◽  
V. R. Badescu ◽  
C. Postolache
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Transformation Rate ◽  
Batch Mode ◽  
Promising Alternative ◽  
Ph Variation ◽  
Microalgae Harvesting ◽  
Cost Efficient

The study used activated algae granules for low-strength wastewater treatment in sequential batch mode. Each treatment cycle was conducted within 24 h in a bioreactor exposed to 235 μmol/m2/s light intensity. Wastewater treatment was performed mostly in aerobic conditions, oxygen being provided by microalgae. High removal efficiency of chemical oxygen demand (COD) was achieved (86–98%) in the first hours of the reaction phase, during which the indicator's removal rate was 17.4 ± 3.9 mg O2/g h; NH4+ was removed during organic matter degradation processes with a rate of 1.8 ± 0.6 mg/g h. After almost complete COD removal, the NH4+ remaining in the liquor was removed through nitrification processes promoted by the increase of the liquor's oxygen saturation (O2%), the transformation rate of NH4+ into NO3− increasing from 0.14 ± 0.05 to 1.5 ± 0.4 mg NH4+/g h, along with an O2% increase. A wide removal efficiency was achieved in the case of PO43– (11–85%), with the indicator's removal rate being 1.3 ± 0.7 mg/g h. In the provided optimum conditions, the occurrence of the denitrifying activity was also noticed. A large pH variation was registered (5–8.5) during treatment cycles. The granular activated algae system proved to be a promising alternative for wastewater treatment as it also sustains cost-efficient microalgae harvesting, with microalgae recovery efficiency ranging between 99.85 and 99.99% after granules settling with a velocity of 19 ± 3.6 m/h.

scholarly journals Removal of organic and nitrogen in a novel anoxic fixed-bed / aerobic fluidized-moving bed integrated with a constructed wetland bio-reactor (A/O-FMCW)

2020 ◽  
Vol 167 ◽  
pp. 01001
Author(s):  
Changmiao Lai ◽  
Yu Sun ◽  
Yong Guo ◽  
Qin Cai ◽  
Ping Yang
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Constructed Wetland ◽  
Removal Rate ◽  
Fixed Bed ◽  
Oxygen Demand ◽  
Integrated System ◽  
Nitrification Rate ◽  
Moving Bed ◽  
Influent Concentration

An innovative hybrid process was designed using an integrated bio-reactor based on an anoxic / aerobic process that combined a fixed bed and a fluidized-moving bed with a constructed wetland (A/OFMCW) to enhance the removal of organic material and nitrogen. The goal was to achieve stringent discharge standards for rural domestic wastewater treatment. A preliminary lab-scale investigation of about 130 days obtained an average COD (Chemical Oxygen Demand) removal rate as high as 92.2% at an average influent concentration of 319.5 mg/L. The average TN (Total Nitrogen) removal efficiency positively correlated with the attached-growth biofilm as observed by SEM (Scanning Electron Microscope), and declined from 79.1% to 53.2%. The was accompanied by a gradual increase in the average influent concentration from 16.73 to 52.01 mg/L despite the relative nitrification rate fluctuating between 92.5% and 97.9%. The entire integrated system improved the COD removal efficiency by nearly 36% and the TN by 14–28%. Classical autotrophic nitrification and heterotrophic denitrification were the main mechanisms responsible for the elimination of pollutants, and the latter was determined to be the limiting step. Overall, this study provides an effective and less expensive alternative method to apply or upgrade DWWT (Decentralized Wastewater Treatment).

scholarly journals Laundry wastewater treatment using a combination of sand filter, bio-char and teff straw media

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Zaher Mundher Yaseen ◽  
Tibebu Tsegaye Zigale ◽  
Tiyasha ◽  
Ravi Kumar D. ◽  
Sinan Q. Salih ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Water Scarcity ◽  
Removal Rate ◽  
Treatment Strategies ◽  
Oxygen Demand ◽  
Total Alkalinity ◽  
Treatment Technique ◽  
Flux Rate ◽  
Eucalyptus Wood

AbstractNumerous researchers have expressed concern over the emerging water scarcity issues around the globe. Economic water scarcity is severe in the developing countries; thus, the use of inexpensive wastewater treatment strategies can help minimize this issue. An abundant amount of laundry wastewater (LWW) is generated daily and various wastewater treatment researches have been performed to achieve suitable techniques. This study addressed this issue by considering the economic perspective of the treatment technique through the selection of easily available materials. The proposed technique is a combination of locally available absorbent materials such as sand, biochar, and teff straw in a media. Biochar was prepared from eucalyptus wood, teff straw was derived from teff stem, and sand was obtained from indigenous crushed stones. In this study, the range of laundry wastewater flow rate was calculated as 6.23–17.58 m3/day; also studied were the efficiency of the media in terms of the removal percentage of contamination and the flux rate. The performances of biochar and teff straw were assessed based on the operation parameters and the percentage removal efficiency at different flux rates; the assessment showed 0.4 L/min flux rate to exhibit the maximum removal efficiency. Chemical oxygen demand, biological oxygen demand, and total alkalinity removal rate varied from 79% to ≥83%; total solids and total suspended solids showed 92% to ≥99% removal efficiency, while dissolved oxygen, total dissolved solids, pH, and electrical conductivity showed 22% to ≥62% removal efficiency. The optimum range of pH was evaluated between 5.8–7.1. The statistical analysis for finding the correlated matrix of laundry wastewater parameters showed the following correlations: COD (r = −0.84), TS (r = −0.83), and BOD (r = −0.81), while DO exhibited highest negative correlation. This study demonstrated the prospective of LWW treatment using inexpensive materials. The proposed treatment process involved low-cost materials and exhibited efficiency in the removal of contaminants; its operation is simple and can be reproduced in different scenarios.

Experimental Comparison between Moving Bed Biofilm Reactor (MBBR) and Conventional Activated Sludge (CAS) for River Purification Treatment Plant

2015 ◽  
Vol 1113 ◽  
pp. 806-811 ◽  
Author(s):  
Lariyah Mohd Sidek ◽  
Hairun Aishah Mohiyaden ◽  
Hidayah Basri ◽  
Gasim Hayder Ahmed Salih ◽  
Ahmad Hussein Birima ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Physical Performance ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Biofilm Reactor ◽  
Moving Bed Biofilm Reactor ◽  
Moving Bed ◽  
Conventional Activated Sludge

Moving Bed Biofilm Reactor (MBBR) systems have been proven as an effective technology for water treatment and have been used for Biochemical Oxygen Demand/Chemical Oxygen Demand (BOD/COD-removal), as well as for nitrification and denitrification in municipal and industrial wastewater treatment. Conventional Activated Sludge (CAS), in particular, has been extensively used in wastewater treatment since decades ago. In this study, physical performance results for both MBBR and CAS were compared and evaluated on laboratory scale basis. The study aims to identify the best system performance in terms of constituent removal efficiency for effective management of the river purification plant. A novel parallel MBBR and CAS pilot plant were fabricated and operated to compare the physical performance of MBBR and CAS. Analysis of the performances for MBBR and CAS show, MBBR has higher COD (85%), AN (75%) and TSS (80%) removal rate compared to CAS COD (53%), AN (53%) and TSS (69%). For BOD removal rate, CAS shows 68% removal rate whereas MBBR shows only 65%. Thus CAS has shown slightly higher removal rate than MBBR. In terms of sludge production, MBBR sludge is less than CAS. Overall performance proves that MBBR has better rate of constituent removal efficiency compared to CAS in the laboratory basis study.

Enhancing nitrogen removal efficiency in a dyestuff wastewater treatment plant with the IFFAS process: the pilot-scale and full-scale studies

2017 ◽  
Vol 77 (1) ◽  
pp. 70-78 ◽  
Author(s):  
Yanjun Mao ◽  
Xie Quan ◽  
Huimin Zhao ◽  
Yaobin Zhang ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Full Scale ◽  
Nitrification And Denitrification ◽  
Dyestuff Wastewater

Abstract The activated sludge (AS) process is widely applied in dyestuff wastewater treatment plants (WWTPs); however, the nitrogen removal efficiency is relatively low and the effluent does not meet the indirect discharge standards before being discharged into the industrial park's WWTP. Hence it is necessary to upgrade the WWTP with more advanced technologies. Moving bed biofilm processes with suspended carriers in an aerobic tank are promising methods due to enhanced nitrification and denitrification. Herein, a pilot-scale integrated free-floating biofilm and activated sludge (IFFAS) process was employed to investigate the feasibility of enhancing nitrogen removal efficiency at different hydraulic retention times (HRTs). The results showed that the effluent chemical oxygen demand (COD), ammonium nitrate (NH4+-N) and total nitrogen (TN) concentrations of the IFFAS process were significantly lower than those of the AS process, and could meet the indirect discharge standards. PCR-DGGE and FISH results indicated that more nitrifiers and denitrifiers co-existed in the IFFAS system, promoting simultaneous nitrification and denitrification. Based on the pilot results, the IFFAS process was used to upgrade the full-scale AS process, and the effluent COD, NH4+-N and TN of the IFFAS process were 91–291 mg/L, 10.6–28.7 mg/L and 18.9–48.6 mg/L, stably meeting the indirect discharge standards and demonstrating the advantages of IFFAS in dyestuff wastewater treatment.

COD removal efficiency and mechanism of HMBR in high volumetric loading for ship domestic sewage treatment

2016 ◽  
Vol 74 (7) ◽  
pp. 1509-1517 ◽  
Author(s):  
Linan Zhu ◽  
Hailing He ◽  
Chunli Wang
Keyword(s):  
Removal Efficiency ◽  
Removal Rate ◽  
Sewage Treatment ◽  
Oxygen Demand ◽  
Domestic Sewage ◽  
Cod Removal ◽  
Aeration Tank ◽  
Remarkable Effect ◽  
Cod Removal Efficiency ◽  
Volumetric Loading

The hybrid membrane bioreactor (HMBR) has been applied in ship domestic sewage treatment under high volumetric loading for ship space saving. The mechanism and influence factors on the efficiency, including hydraulic retention time (HRT), dissolved oxygen (DO) of chemical oxygen demand (COD) removal were investigated. The HMBR's average COD removal rate was up to 95.13% on volumetric loading of 2.4 kgCOD/(m3•d) and the COD concentration in the effluent was 48.5 mg/L, far below the International Maritime Organization (IMO) discharge standard of 125 mg/L. DO had a more remarkable effect on the COD removal efficiency than HRT. In addition, HMBR revealed an excellent capability of resisting organics loading impact. Within the range of volumetric loading of 0.72 to 4.8 kg COD/(m3•d), the effluent COD concentration satisfied the discharge requirement of IMO. It was found that the organics degradation in the aeration tank followed the first-order reaction, with obtained kinetic parameters of vmax (2.79 d−1) and Ks (395 mg/L). The original finding of this study had shown the effectiveness of HMBR in organic contaminant degradation at high substrate concentration, which can be used as guidance in the full scale of the design, operation and maintenance of ship domestic sewage treatment devices.

scholarly journals Investigation of the Efficiency of Phosphorus Removal Using Anionic Resins From the Continuous Flow in the Waste Stabilization Pond Outlet: A Case Study of Kaboodrahang Wastewater Treatment Plant

2019 ◽  
Vol 6 (1) ◽  
pp. 16-20
Author(s):  
Ali Akbar Rahmani Sarmazdeh ◽  
Mostafa Leili
Keyword(s):  
Wastewater Treatment ◽  
Wastewater Treatment Plant ◽  
Phosphorus Removal ◽  
Continuous Flow ◽  
Removal Rate ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Cold Season ◽  
Stabilization Pond ◽  
The Mean

This research mainly aimed to investigate phosphorus removal from stabilization pond effluent by using anionic resins in the continuous flow mode of operation due to high amounts of phosphorus in the wastewater treatment plant effluent of Kaboodrahang, western Iran, as well as the violation from a prescribed effluent standard to discharge receiving the surface waters. For this purpose, the pilot was made of a plexiglass cylinder and other equipment such as pump and other accessories, as well as Purolite A-100 resin. The reactor effects on the desired study parameters were assessed in two warm and cold seasons. The results showed that the phosphorus concentrations reduced from 7-10 mg/L to 4-7 mg/L and the rate of phosphorus removal was higher in the hot season compared to the cold season. Moreover, the optimum temperature and pH were obtained 21ºC and 8.5, respectively. The mean inlet biological oxygen demand (BOD) was 150 mg/L for both warm and cold seasons, where the highest removal rate of 17% was obtained in the cold season. The mean chemical oxygen demand concentration of the pilot was 250 mg/L for both seasons, and the highest removal rate was observed in the cold season with an efficiency of 18%. Regarding the total suspended solids with the mean inlet of 230 mg/L, the highest removal efficiency was obtained 6% in the warm season.

scholarly journals Combined Application of UV Photolysis and Ozonation with Biological Aerating Filter in Tertiary Wastewater Treatment

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Zhaoqian Jing ◽  
Shiwei Cao
Keyword(s):  
Molecular Weight ◽  
Wastewater Treatment ◽  
Organic Pollutants ◽  
Wastewater Treatment Plants ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Secondary Effluent ◽  
Uv Photolysis ◽  
Combined Application

To enhance the biodegradability of residual organic pollutants in secondary effluent of wastewater treatment plants, UV photolysis and ozonation were used in combination as pretreatment before a biological aerating filter (BAF). The results indicated that UV photolysis could not remove much COD (chemical oxygen demand), and the performance of ozonation was better than the former. With UV photolysis combined with ozonation (UV/O3), COD removal was much higher than the sum of that with UV photolysis and ozonation alone, which indicated that UV photolysis could efficiently promote COD removal during ozonation. This pretreatment also improved molecular weight distribution (MWD) and biodegradability greatly. Proportion of organic compounds with molecular weight (MW) <3 kDalton was increased from 51.9% to 85.9%. COD removal rates with BAF and O3/BAF were only about 25% and 38%, respectively. When UV/O3oxidation was combined with BAF, the average COD removal rate reached above 61%, which was about 2.5 times of that with BAF alone. With influent COD ranging from 65 to 84 mg/L, the effluent COD was stably in the scope of 23–31 mg/L. The combination of UV/O3oxidation with BAF was quite efficient in organic pollutants removal for tertiary wastewater treatment.

Removal of pharmaceutical residue in municipal wastewater by DAF (dissolved air flotation)–MBR (membrane bioreactor) and ozone oxidation

2012 ◽  
Vol 66 (12) ◽  
pp. 2546-2555 ◽  
Author(s):  
Miyoung Choi ◽  
Dong Whan Choi ◽  
Jung Yeol Lee ◽  
Young Suk Kim ◽  
Bun Su Kim ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Membrane Bioreactor ◽  
Municipal Wastewater ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ozone Oxidation ◽  
Dissolved Air Flotation ◽  
Treatment Processes ◽  
Pharmaceutical Residue ◽  
Dissolved Air

Growing attention is given to pharmaceutical residue in the water environment. It is known that pharmaceuticals are able to survive from a series of wastewater treatment processes. Concerns regarding pharmaceutical residues are attributed to the fact that they are being detected in water and sediment environment ubiquitously. Pharmaceutical treatment using a series of wastewater treatment processes of the DAF (dissolved air flotation)–MBR (membrane bioreactor)–ozone oxidation was conducted in the study. DAF, without addition of coagulant, could remove CODcr (chemical oxygen demand by Cr) up to over 70%, BOD 73%, SS 83%, T-N 55%, NH4+ 23%, and T-P 65% in influent of municipal wastewater. Average removal rates of water quality parameters by the DAF–MBR system were very high, e.g. CODcr 95.88%, BOD5 99.66%, CODmn (chemical oxygen demand by Mn) 93.63%, T-N 69.75%, NH4-N 98.46%, T-P 78.23%, and SS 99.51%, which satisfy effluent water quality standards. Despite the high removal rate of the wastewater treatment system, pharmaceuticals were eliminated to be about 50–99% by the MBR system, depending on specific pharmaceuticals. Ibuprofen was well removed by MBR system up to over 95%, while removal rate of bezafibrate ranged between 50 and 90%. With over 5 mg/l of ozone oxidation, most pharmaceuticals which survived the DAF–MBR process were removed completely or resulted in very low survival rate within the range of few micrograms per litre. However, some pharmaceuticals such as bezafibrate and naproxen tended to be resistant to ozone oxidation.

scholarly journals Bioaugmentation with Mixed Hydrogen-Producing Acetogen Cultures Enhances Methane Production in Molasses Wastewater Treatment

Archaea ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Shuo Wang ◽  
Jianzheng Li ◽  
Guochen Zheng ◽  
Guocheng Du ◽  
Ji Li
Keyword(s):  
Wastewater Treatment ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Anaerobic Wastewater Treatment ◽  
Rate Limiting Step ◽  
Limiting Step ◽  
Molasses Wastewater ◽  
Cod Removal Rate ◽  
Rate Limiting

Hydrogen-producing acetogens (HPA) have a transitional role in anaerobic wastewater treatment. Thus, bioaugmentation with HPA cultures can enhance the chemical oxygen demand (COD) removal efficiency and CH4yield of anaerobic wastewater treatment. Cultures with high degradation capacities for propionic acid and butyric acid were obtained through continuous subculture in enrichment medium and were designated as Z08 and Z12. Bioaugmentation with Z08 and Z12 increased CH4production by glucose removal to 1.58. Bioaugmentation with Z08 and Z12 increased the COD removal rate in molasses wastewater from 71.60% to 85.84%. The specific H2and CH4yields from COD removal increased by factors of 1.54 and 1.63, respectively. Results show that bioaugmentation with HPA-dominated cultures can improve CH4production from COD removal. Furthermore, hydrogen-producing acetogenesis was identified as the rate-limiting step in anaerobic wastewater treatment.

The Aeration Time Influence on the Brewery Wastewater Treatment in SBR

2011 ◽  
Vol 183-185 ◽  
pp. 1200-1203
Author(s):  
Jun Sheng Li ◽  
Zhi Wei Zhao ◽  
Jin Long Zuo
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Phosphate Removal ◽  
Experimental Result ◽  
Brewery Wastewater ◽  
Aeration Time

The effect s of aeration time on the treatment of brewery wastewater in SBR reactor were investigated by using synthetic brewery wastewater. The experimental result indicates that under the condition of influent COD is 300～650mg/L, the temperature is 25°C, continual aerations is 2.5 h and sludge density is 2000～3000 mg/L, the reactor has a good degeneration ability of COD and NH4+-N in simulation brewery wastewater，removal rate can reached 90 % or more，phosphate removal efficiency was above 70%. so the SBR technology is feasible．

Sign in / Sign up

Export Citation Format

Share Document