Imparting Pharmaceutical Applications to the Surface of Fabrics for Wound and Skin Care by Ultrasonic Waves

2019 ◽  
Vol 25 (41) ◽  
pp. 5739-5754 ◽  
Author(s):  
Aharon Gedanken ◽  
Nina Perkas ◽  
Ilana Perelshtein ◽  
Anat Lipovsky
Keyword(s):  
Biofilm Formation ◽  
High Speed ◽  
Skin Diseases ◽  
Ultrasonic Waves ◽  
Skin Care ◽  
Speed Up ◽  
Treatment Of Wounds ◽  
New Applications ◽  
Specific Experiment

In this review, we report the functionalization of textiles composed of nanoscale reactive materials in the treatment of wounds and skin diseases such as acne. In view of the growing demand for high-quality textiles, much research is focused on the creation of antimicrobial finishings for fabrics, in order to protect customers from pathogenic or odorgenerating microorganisms. We present coatings from inorganic, organic and biochemical nanoparticles (NPs) on surfaces that impart the ability to kill bacteria, avoid biofilm formation and speed up the recovery of wounds. In all three cases, sonochemistry is used for immobilizing the nanoparticles on the surfaces. The Introduction broadly covers the progress of nanotechnology in the fields of wound and skin care. The first section of this review outlines the mechanism of the ultrasound-assisted deposition of nanoparticles on textiles. The coating can be performed by an in-situ process in which the nanoparticles are formed and subsequently thrown onto the surface of the fabrics at a very high speed. This approach was used in depositing metal-oxide NPs such as ZnO, CuO and Zn-CuO or the organic NPs of tannic acid, chitosan, etc. on textiles. In addition, the sonochemical process can be used as a "throwing stone" technique, namely, previously synthesized or commercially purchased NPs can be placed in the sonication bath and sonicated in the presence of the fabric. The collapse of the acoustic bubble in the solution causes the throwing of the immersed commercial NPs onto the textiles. This section will also outline why sonochemical deposition on textiles is considered the best coating technique. The second section will discuss new applications of the sonochemically- coated textiles in killing bacteria, avoiding biofilm formation and more. Two points should be noted: 1) the review will primarily report results obtained at Bar-Ilan University and 2) since for all textiles tested in our experiments (cotton, polyester, nylon, nonwoven) similar results were obtained, the type of textile used in a specific experiment will not be mentioned - textiles will be discussed in general. It is also worth emphasizing that this review concentrates only on the sonochemical coating of textiles, ignoring other deposition techniques.

An atomic-resolution microscope study of Al contracts on GaAs

1986 ◽  
Vol 44 ◽  
pp. 726-727
Author(s):  
Z. Liliental-Weber ◽  
C. Nelson ◽  
R. Ludeke ◽  
R. Gronsky ◽  
J. Washburn
Keyword(s):  
High Speed ◽  
Schottky Contacts ◽  
Detailed Knowledge ◽  
The Past ◽  
Semiconductor Interfaces ◽  
Deposited Metal ◽  
Microwave Applications ◽  
Free Interfaces ◽  
Potential Use

The properties of metal/semiconductor interfaces have received considerable attention over the past few years, and the Al/GaAs system is of special interest because of its potential use in high-speed logic integrated optics, and microwave applications. For such materials a detailed knowledge of the geometric and electronic structure of the interface is fundamental to an understanding of the electrical properties of the contact. It is well known that the properties of Schottky contacts are established within a few atomic layers of the deposited metal. Therefore surface contamination can play a significant role. A method for fabricating contamination-free interfaces is absolutely necessary for reproducible properties, and molecularbeam epitaxy (MBE) offers such advantages for in-situ metal deposition under UHV conditions

Scanning x-ray fluorescence microscopy and principal component analysis

1992 ◽  
Vol 50 (2) ◽  
pp. 1752-1753
Author(s):  
Brian Cross
Keyword(s):  
Principal Component Analysis ◽  
Fluorescence Microscopy ◽  
Spatial Resolution ◽  
High Speed ◽  
Image Acquisition ◽  
Principal Component ◽  
Fluorescence Microscope ◽  
Acquisition Rate ◽  
X Ray ◽  
Speed Up

A relatively new entry, in the field of microscopy, is the Scanning X-Ray Fluorescence Microscope (SXRFM). Using this type of instrument (e.g. Kevex Omicron X-ray Microprobe), one can obtain multiple elemental x-ray images, from the analysis of materials which show heterogeneity. The SXRFM obtains images by collimating an x-ray beam (e.g. 100 μm diameter), and then scanning the sample with a high-speed x-y stage. To speed up the image acquisition, data is acquired "on-the-fly" by slew-scanning the stage along the x-axis, like a TV or SEM scan. To reduce the overhead from "fly-back," the images can be acquired by bi-directional scanning of the x-axis. This results in very little overhead with the re-positioning of the sample stage. The image acquisition rate is dominated by the x-ray acquisition rate. Therefore, the total x-ray image acquisition rate, using the SXRFM, is very comparable to an SEM. Although the x-ray spatial resolution of the SXRFM is worse than an SEM (say 100 vs. 2 μm), there are several other advantages.

scholarly journals Spatially Resolved Experimental Modal Analysis on High-Speed Composite Rotors Using a Non-Contact, Non-Rotating Sensor

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4705
Author(s):  
Julian Lich ◽  
Tino Wollmann ◽  
Angelos Filippatos ◽  
Maik Gude ◽  
Juergen Czarske ◽  
...  
Keyword(s):  
High Speed ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Fiber Reinforced ◽  
Structural Dynamic ◽  
Spatially Resolved ◽  
Glass Fiber Reinforced ◽  
Vibration Responses ◽  
And Performance

Due to their lightweight properties, fiber-reinforced composites are well suited for large and fast rotating structures, such as fan blades in turbomachines. To investigate rotor safety and performance, in situ measurements of the structural dynamic behaviour must be performed during rotating conditions. An approach to measuring spatially resolved vibration responses of a rotating structure with a non-contact, non-rotating sensor is investigated here. The resulting spectra can be assigned to specific locations on the structure and have similar properties to the spectra measured with co-rotating sensors, such as strain gauges. The sampling frequency is increased by performing consecutive measurements with a constant excitation function and varying time delays. The method allows for a paradigm shift to unambiguous identification of natural frequencies and mode shapes with arbitrary rotor shapes and excitation functions without the need for co-rotating sensors. Deflection measurements on a glass fiber-reinforced polymer disk were performed with a diffraction grating-based sensor system at 40 measurement points with an uncertainty below 15 μrad and a commercial triangulation sensor at 200 measurement points at surface speeds up to 300 m/s. A rotation-induced increase of two natural frequencies was measured, and their mode shapes were derived at the corresponding rotational speeds. A strain gauge was used for validation.

Enhanced Grain Refinement of W18Cr4V High‐Speed Steel using in situ TiN‐Nb‐Cr@Graphene/Fe Nanocomposite Inoculant

2021 ◽  
Author(s):  
Lina Bai ◽  
Chunxiang Cui ◽  
Jianjun Zhang ◽  
Lichen Zhao ◽  
Guixing Zheng ◽  
...  
Keyword(s):  
Grain Refinement ◽  
High Speed ◽  
High Speed Steel

scholarly journals Influence of Hydrogeochemistry on Tunnel Drainage in Evaporitic Formations: El Regajal Tunnel Case Study (Aranjuez, Spain)

2021 ◽  
Vol 13 (3) ◽  
pp. 1505
Author(s):  
Ignacio Menéndez Pidal ◽  
Jose Antonio Mancebo Piqueras ◽  
Eugenio Sanz Pérez ◽  
Clemente Sáenz Sanz
Keyword(s):  
High Speed ◽  
Civil Engineering ◽  
Saturation Index ◽  
The Subject ◽  
Under Construction ◽  
Underground Flow ◽  
Very High ◽  
Over Time

Many of the large number of underground works constructed or under construction in recent years are in unfavorable terrains facing unusual situations and construction conditions. This is the case of the subject under study in this paper: a tunnel excavated in evaporitic rocks that experienced significant karstification problems very quickly over time. As a result of this situation, the causes that may underlie this rapid karstification are investigated and a novel methodology is presented in civil engineering where the use of saturation indices for the different mineral specimens present has been crucial. The drainage of the rock massif of El Regajal (Madrid-Toledo, Spain, in the Madrid-Valencia high-speed train line) was studied and permitted the in-situ study of the hydrogeochemical evolution of water flow in the Miocene evaporitic materials of the Tajo Basin as a full-scale testing laboratory, that are conforms as a whole, a single aquifer. The work provides a novel methodology based on the calculation of activities through the hydrogeochemical study of water samples in different piezometers, estimating the saturation index of different saline materials and the dissolution capacity of the brine, which is surprisingly very high despite the high electrical conductivity. The circulating brine appears unsaturated with respect to thenardite, mirabilite, epsomite, glauberite, and halite. The alteration of the underground flow and the consequent renewal of the water of the aquifer by the infiltration water of rain and irrigation is the cause of the hydrogeochemical imbalance and the modification of the characteristics of the massif. These modifications include very important loss of material by dissolution, altering the resistance of the terrain and the increase of the porosity. Simultaneously, different expansive and recrystallization processes that decrease the porosity of the massif were identified in the present work. The hydrogeochemical study allows the evolution of these phenomena to be followed over time, and this, in turn, may facilitate the implementation of preventive works in civil engineering.

In Situ Observation Method for Quantitative Evaluation of Solidification Phenomena and Solidification Cracks during Welding

2014 ◽  
Vol 782 ◽  
pp. 3-7
Author(s):  
Kenji Shinozaki ◽  
Motomichi Yamamoto ◽  
Kohta Kadoi ◽  
Peng Wen
Keyword(s):  
High Speed ◽  
Video Camera ◽  
Solidification Cracking ◽  
In Situ Observation ◽  
High Speed Video Camera ◽  
Varestraint Test ◽  
Solidification Cracks ◽  
Observation Method ◽  
Solidification Crack

Solidification cracking during welding is very serious problem for practical use. Therefore, there are so many reports concerning solidification cracking. Normally, solidification cracking susceptibility of material is quantitatively evaluated using Trans-Varestraint test. On the other hand, local solidification cracking strain was tried to measure precisely using in-situ observation method, called MISO method about 30 years ago. Recently, digital high-speed video camera develops very fast and its image quality is very high. Therefore, we have started to observe solidification crack using in site observation method. In this paper, the local critical strain of a solidification crack was measured and the high temperature ductility curves of weld metals having different dilution ratios and different grain sizes to evaluate quantitatively the effects of dilution ratio and grain size on solidification cracking susceptibility by using an improved in situ observation method.

Effect of food preservatives on in situ biofilm formation

2008 ◽  
Vol 12 (3) ◽  
pp. 203-208 ◽  
Author(s):  
Nicole Birgit Arweiler ◽  
Ronaldo Lenz ◽  
Anton Sculean ◽  
Ali Al-Ahmad ◽  
Elmar Hellwig ◽  
...  
Keyword(s):  
Biofilm Formation ◽  
Food Preservatives ◽  
Effect Of Food

Microwave On-Line Measurements on Conveyed Products Application to Paper and Wood Industries

1994 ◽  
Vol 347 ◽  
Author(s):  
J.Ch. Bolomey ◽  
G. Cottard ◽  
P. Berthaud ◽  
A. Lemaitre ◽  
J. F. Portala
Keyword(s):  
High Speed ◽  
Transformation Process ◽  
Wood Material ◽  
Quantitative Measurements ◽  
On Line ◽  
Phase Data ◽  
Polynomial Expansions ◽  
Physical Quantities ◽  
Data Calibration

ABSTRACTMicrowave multiport sensors have been shown to provide some unique capabilities to achieve real-time testing of products conveyed at high speed. In many applications, quantitative measurements of physical quantities such as moisture content, density, etc… are required, either to guarantee reliable production or to optimally control a fabrication/transformation process. In this paper, different ways of extracting such physical quantities from microwave measurements performed by multiport sensors are presented. Model approaches are used, based on polynomial expansions of the physical quantities to be measured as a function of the microwave amplitude and phase data. Calibration procedures have been investigated for both paper and wood material samples. Comparisons between in-situ, microwave and conventional, measurements are analysed.

Sign in / Sign up

Export Citation Format

Share Document