Design and Performance Analysis of Distributed Equal Angle Spiral Vertical Axis Wind Turbine

2020 ◽  
Vol 14 (1) ◽  
pp. 120-132
Author(s):  
Li Zheng ◽  
Zhang Wenda ◽  
Han Ruihua ◽  
Tian Yongsheng
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Energy Utilization ◽  
Normal Operation ◽  
Utilization Rate ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine

Background: The wind turbine is divided into a horizontal axis and a vertical axis depending on the relative positions of the rotating shaft and the ground. The advantage of the choke wind turbine is that the starting torque is large and the starting performance is good. The disadvantage is that the rotation resistance is large, the rotation speed is low, the asymmetric flow occurs when the wind wheel rotates, the lateral thrust is generated, and the wind energy utilization rate is lowered. How to improve the wind energy utilization rate of the resistance wind turbine is an important issue to be solved by the wind power technology. Objective: The nautilus isometric spiral wind turbines studied in this paper have been introduced and analyzed in detail, preparing for the further flow analysis and layout of wind turbines, improving the wind energy utilization rate of wind turbines, introducing patents of other structures and output characteristics of its generator set. Methods: Combined with the flow field analysis of ANSYS CFX software, the numerical simulation of the new wind turbine was carried out, and the aerodynamic performance of the new vertical axis wind turbine was analyzed. The mathematical model and control model of the generator were established by the maximum power control method, and the accuracy of the simulation results was verified by the measured data. Results: The basic parameters of the new wind turbine tip speed ratio, torque coefficient and wind energy utilization coefficient are analyzed. Changes in wind speed, pressure and eddy viscosity were investigated. Three-dimensional distribution results of wake parameters such as wind speed and pressure are obtained. By simulating the natural wind speed, the speed and output current of the generator during normal operation are obtained. Conclusion: By analyzing the wind performance and power generation characteristics of the new wind turbine, the feasibility of the new wind turbine is determined, which provides reference and reference for the optimal design and development of the wind turbine structure.

Design and performance evaluation of vertical axis wind turbine for wind energy harvesting at railway

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hashwini Lalchand Thadani ◽  
Fadia Dyni Zaaba ◽  
Muhammad Raimi Mohammad Shahrizal ◽  
Arjun Singh Jaj A. Jaspal Singh Jaj ◽  
Yun Ii Go
Keyword(s):  
Wind Speed ◽  
Energy Harvesting ◽  
Wind Energy ◽  
Wind Turbine ◽  
High Speed ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Modeling Tools ◽  
Content Type

PurposeThis paper aims to design an optimum vertical axis wind turbine (VAWT) and assess its techno-economic performance for wind energy harvesting at high-speed railway in Malaysia.Design/methodology/approachThis project adopted AutoCAD and ANSYS modeling tools to design and optimize the blade of the turbine. The site selected has a railway of 30 km with six stops. The vertical turbines are placed 1 m apart from each other considering the optimum tip speed ratio. The power produced and net present value had been analyzed to evaluate its techno-economic viability.FindingsComputational fluid dynamics (CFD) analysis of National Advisory Committee for Aeronautics (NACA) 0020 blade has been carried out. For a turbine with wind speed of 50 m/s and swept area of 8 m2, the power generated is 245 kW. For eight trains that operate for 19 h/day with an interval of 30 min in nonpeak hours and 15 min in peak hours, total energy generated is 66 MWh/day. The average cost saved by the train stations is RM 16.7 mil/year with battery charging capacity of 12 h/day.Originality/valueWind energy harvesting is not commonly used in Malaysia due to its low wind speed ranging from 1.5 to 4.5 m/s. Conventional wind turbine requires a minimum cut-in wind speed of 11 m/s to overcome the inertia and starts generating power. Hence, this paper proposes an optimum design of VAWT to harvest an unconventional untapped wind sources from railway. The research finding complements the alternate energy harvesting technologies which can serve as reference for countries which experienced similar geographic constraints.

scholarly journals Influence of wind energy utilization potential in urban suburbs: a case study of Hohhot

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Wang Wenxin ◽  
Chen Kexin ◽  
Bai Yang ◽  
Xu Yun ◽  
Wang Jianwen
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Statistical Properties ◽  
Energy Utilization ◽  
Energy Output ◽  
Distribution Model ◽  
Horizontal Axis Wind Turbine

AbstractGiven the increasing trend of using wind energy in cities, the utilization of distributed wind energy in cities has been widely concerned by researchers. The related research on the micro-site selection of wind turbines, a sub-project of the Task27 project of the International energy agency, was continued in this paper. The wind speed data of an observation station near Hohhot, Inner Mongolia, with a range of 10–19 m were collected. The evaluation included wind direction, Weibull parameter characteristics, and turbulence intensity. The potential energy output in 10 different heights was estimated using commercial horizontal and vertical axis wind turbines of the same power. Results showed that the following: the three-parameter Weibull distribution model can well describe the statistical properties of the wind speed in this site. The wind speed distribution model constructed from extrapolation parameters reflects the wind speed statistical properties out of detection positions to a certain extent. The wind energy density of the vertical axis wind turbine is slightly lower than that of the horizontal axis wind turbine. Furthermore, more power can be generated from March to May.

scholarly journals Experimental Study of Wind Booster Addition for Savonius Vertical Wind Turbine of Two Blades Variations Using Low Wind Speed

2019 ◽  
Vol 125 ◽  
pp. 14003
Author(s):  
Eflita Yohana ◽  
MSK. Tony Suryo U ◽  
Binawan Luhung ◽  
Mohamad Julian Reza ◽  
M Badruz Zaman
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Average Value ◽  
Low Wind Speed

The Wind turbine is a tool used in Wind Energy Conversion System (WECS). The wind turbine produces electricity by converting wind energy into kinetic energy and spinning to produce electricity. Vertical Axis Wind Turbine (VAWT) is designed to produce electricity from winds at low speeds. Vertical wind turbines have 2 types, they are wind turbine Savonius and Darrieus. This research is to know the effect of addition wind booster to Savonius vertical wind turbine with the variation 2 blades and 3 blades. Calculation the power generated by wind turbine using energy analysis method using the concept of the first law of thermodynamics. The result obtained is the highest value of blade power in Savonius wind turbine without wind booster (16.5 ± 1.9) W at wind speed 7 m/s with a tip speed ratio of 1.00 ± 0.01. While wind turbine Savonius with wind booster has the highest power (26.3 ± 1.6) W when the wind speed of 7 m/s with a tip speed ratio of 1.26 ± 0.01. The average value of vertical wind turbine power increases Savonius after wind booster use of 56%.

scholarly journals Influence of Wind Energy Utilization Potential in Urban Suburbs: A Case Study of Hohhot

2020 ◽  
Author(s):  
wang Wenxin ◽  
Bai Yang ◽  
Chen Kexin ◽  
Wang Jianwen ◽  
Qin Chaofan
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Statistical Properties ◽  
Energy Utilization ◽  
Energy Output ◽  
Distribution Model ◽  
Horizontal Axis Wind Turbine

Abstract Background：Given the increasing trend of using wind energy in cities, the utilization of distributed wind energy in cities has been widely concerned by researchers. The related research on the micro-site selection of wind turbines, a sub-project of the Task27 project of the International energy agency, was continued in this paper.Methods：The wind speed data of an observation station near Hohhot, Inner Mongolia, with a range of 10-19 m were collected. The evaluation included wind direction, Weibull parameter characteristics, and turbulence intensity. The potential energy output in 10 different heights was estimated using commercial horizontal and vertical axis wind turbines of the same power.Results：The three-parameter Weibull distribution model can well describe the statistical properties of the wind speed in this site. The wind speed distribution model constructed from extrapolation parameters reflects the wind speed statistical properties out of detection positions to a certain extent.Conclusions：The wind energy density of the vertical axis wind turbine is slightly lower than that of the horizontal axis wind turbine. Furthermore, more power can be generated from March to May.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

Optimized Small Vertical Axis Wind Turbine (VAWT), Phase I

2021 ◽  
Author(s):  
Moshe Zilberman ◽  
Abdelaziz Abu Sbaih ◽  
Ibrahim Hadad
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Cost Effective ◽  
Clean Energy ◽  
Vertical Axis ◽  
Low Noise ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Different Types

Abstract Wind energy has become an important resource for the growing demand for clean energy. In 2020 wind energy provided more than 6% of the global electricity demand. It is expected to reach 7% at the end of 2021. The installation growth rate of small wind turbines, though, is relatively slow. The reasons we are interested in the small vertical axis wind turbines are their low noise, environmentally friendly, low installation cost, and capable of being rooftop-mounted. The main goal of the present study is an optimization process towards achieving the optimal cost-effective vertical wind turbine. Thirty wind turbine models were tested under the same conditions in an Azrieli 30 × 30 × 90 cm low-speed wind tunnel at 107,000 Reynolds number. The different types of models were obtained by parametric variations of five basic models, maintaining the same aspect ratio but varying the number of bucket phases, the orientation angles, and the gaps between the vanes. The best performing turbine model was made of one phase with two vanes of non-symmetric bipolynomial profiles that exhibited 0.2 power coefficient, relative to 0.16 and 0.13 that were obtained for symmetrical polynomial and the original Savonius type turbines, respectively. Free rotation, static forces and moments, and dynamic moments and power were measured for the sake of comparison and explanation for the variations in performances of different types of turbines. CFD calculations were used to understand the forces and moment behaviors of the optimized turbine.

Prediction of Aerodynamic Noise Radiated From a Vertical-Axis Wind Turbine

2003 ◽  
Author(s):  
Akiyoshi Iida ◽  
Akisato Mizuno ◽  
Kyoji Kamemoto
Keyword(s):  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Sound Source ◽  
Vertical Axis ◽  
Aerodynamic Performance ◽  
Low Noise ◽  
Aerodynamic Noise ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine

Unsteady flow field and flow induced noise of vertical axis wind turbine are numerically investigated. The flow field is numerically calculated by the vortex method with core-spreading model. This simulation obtains aerodynamic performance and aerodynamic forces. Aerodynamic noise is also simulated by using Ffowcs Williams-Hawkings equation with compact body and low-Mach number assumptions. Tip speed of rotor blades are not so high, then the contribution of the moving sound source is smaller than that of the dipole sound source. Since the maximum power coefficient of VAWT can be obtained at lower tip-speed ratio compared to the conventional, horizontal axis wind turbines, the aerodynamic noise from vertical axis wind turbine is smaller than that of the conventional wind turbines at the same aerodynamic performance. This result indicates that the vertical axis wind turbines are useful to develop low-noise wind turbines.

scholarly journals Relationship between Starting Torque and Thermal Behaviour for a Permanent Magnet Synchronous Generator (PMSG) Applied with Vertical Axis Wind Turbine (VAWT)

2021 ◽  
Vol 13 (16) ◽  
pp. 9151
Author(s):  
Mintra Trongtorkarn ◽  
Thanansak Theppaya ◽  
Kuaanan Techato ◽  
Montri Luengchavanon ◽  
Chainuson Kasagepongsarn
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Permanent Magnet ◽  
Wind Turbines ◽  
High Speed ◽  
Electrical Power ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Minimization Method ◽  
Starting Torque

The application of wind turbine technology in low wind speed regions such as Southeast Asia has recently attracted increased attention. Wind turbines are designed as special structures with low starting torque, and many starting torque minimization processes exist for permanent magnet synchronous generators (PMSGs). Plurality is applied to decrease the starting torque in radial flux permanent magnet disk generators. The most popular starting torque minimization method uses a magnet skew technique. When used at 20°, this technique reduced starting torque by 4.72% (on load) under 500 rpm at 50 Hz for 120 min. By contrast, a PMSG with magnet skew conditions set at under 2° reduced electrical power by 3.86%. For high-speed PMSGs, magnet skew techniques affect the generation of heat in the coils (stator), with heat decrease at the middle of the coil, on its surface and between the coils at 2.90%, 3.10% and 2.40%, respectively. PMSGs were installed in vertical axis wind turbines (VAWTs), and heat generation in relation to wind speed and electrical power was assessed. Magnet skew techniques can be used in PMSGs to reduce staring torque, while skew techniques also reduce electrical power and heat generated at the stator.

Performance Analysis of Casement Type Vertical Axis Wind Turbine

2013 ◽  
Author(s):  
Sandeep S. Wangikar ◽  
Sharad U. Jagtap ◽  
Abhijeet B. Tarmude ◽  
Abhishek S. Pore ◽  
Sushil P. Shinde
Keyword(s):  
Wind Speed ◽  
Performance Analysis ◽  
Wind Energy ◽  
Wind Turbine ◽  
Control Parameter ◽  
Vertical Axis ◽  
Renewable Energies ◽  
Control Parameters ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

Increasing worldwide demand for electricity requires the need for harnessing different kinds of renewable energies like wind energy. An increase in prevalence of vertical axis wind turbine (VAWT) has renewed interest in developing the new configurations of vertical axis wind turbines for better performance. This paper describes the performance analysis of a casement type vertical axis wind turbine (CTVAWT). The model of CTVAWT has been manufactured and tested to predict the performance. The performance analysis of CTVAWT was carried out by varying the control parameters such as wind speed and casement angle. The effect of each control parameter on the response parameters i.e. torque and power have been analyzed (by conducting various experiments of CTVAWT).The torque and power increases with increase in casement angle up to 40 degrees further decrease with increase in casement angle. From this analysis the newly developed CTVAWT is working efficiently at 40 degrees.

Dynamic Analysis of the Optimized Savonius Vertical Axis Wind Turbine Composite Blades

2021 ◽  
pp. 1-7
Author(s):  
Sobhy Ghoneam ◽  
Ahmed Hamada ◽  
Taha S. Sherif
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Dynamic Characteristics ◽  
Dynamic Performance ◽  
Vertical Axis ◽  
Mode Shapes ◽  
Speed Ratio ◽  
Damping Factor ◽  
Vertical Axis Wind Turbine ◽  
Composite Blades

Abstract This paper presents a comprehensive study of the dynamic behavior of small vertical axis wind turbines (VAWTs) based on local fabricated Savonius VAWTs, which is suitable for countries that have moderate wind speed. The merits of this design are cleanliness, silent, start-up under low wind speed, independent wind directions, adaptability and ease of manufacturing. Also, this paper presents an experimental validation study for the optimized Savonius VAWT. Four verification test configurations of the optimized VAWT composite blades are designed, simulated and fabricated of Glass – Polyester with different stacking sequence layout for each. Modified mechanical parameters are introduced to improve the scalability, reliability, and accuracy of the developed models. Based on wind energy conversion system basics, aerodynamic characteristics (tip speed ratio (λ) and coefficient of power (Cp)), dynamic characteristics (natural frequencies and mode shapes) of Savonius-rotor models are presented and simulated within SOLIDWORKS Simulation 2020 software. The dynamic characteristics such as frequency, mode shape and damping factor are extensively investigated using Fast Fourier Transformer (FFT) analyzer. The results show that the role of composite material blades in improving the dynamic performance of a wind turbine is significant.

Sign in / Sign up

Export Citation Format

Share Document