scholarly journals QUALITY BY DESIGN (QBD) AS A TOOL FOR THE OPTIMIZATION OF INDOMETHACIN FREEZE-DRIED SUBLINGUAL TABLETS: IN VITRO AND IN VIVO EVALUATION

2021 ◽  
pp. 160-171
Author(s):  
MERVAT SHAFIK IBRAHIM ◽  
NIHAL MOHAMED ELMAHDY ELSAYYAD ◽  
ABEER SALAMA ◽  
SHEREEN H. NOSHI
Keyword(s):  
Response Surface ◽  
Quality By Design ◽  
Drug Dissolution ◽  
Disintegration Time ◽  
Optimization Study ◽  
Freeze Dried ◽  
Screening Study ◽  
Wetting Time

Objective: This study aims to prepare and optimize indomethacin freeze-dried sublingual tablets (IND-FDST) by utilizing a quality by design (QbD) approach to achieve rapid drug dissolution and simultaneously bypassing the GIT for better patient tolerability. Methods: A screening study was utilized to determine the most significant factors which the quality attributes, namely disintegration time and % friability. Then an optimization study was conducted using a full response surface design to determine the optimized formula by varying the amount of the matrix-forming polymer (gelatin) and super disintegrant (croscarmellose sodium (CCS)). The variables' effect on the % friability, disintegration time, wetting time, and amount of drug release after 10 min (%Q10) was studied. The optimized formula was tested for compatibility, morphology as well as stability studies under accelerated conditions in addition to the in vivo pharmacodynamics in rats. QbD was adopted by utilizing a screening study to identify the significant formulation factors followed by a response surface optimization study to determine the optimized IND-FDST formulation. Results: Optimized IND-FDST comprised of gelatin/CCS combination in a ratio of 1:1 possessed adequate %friability (0.73±0.03%), disintegration time (25.40±1.21 seconds), wetting time (3.49±0.68 seconds), and % Q10 (100.99±5.29%) as well as good stability under accelerated conditions. IND-FDST also showed significant inhibition of edema, tumour necrosis factor-alpha, and interleukin-6 release in vivo compared to the oral market product by 70%, 42%, and 65%, respectively. Conclusion: QbD presents a successful approach in the optimization of a successful IND-FDST formula that showed superior in vivo and in vitro characteristics.

scholarly journals DESIGN, OPTIMIZATION AND EVALUATION OF IBUPROFEN FAST DISSOLVING TABLETS EMPLOYING STARCH PHTHALATE-A NOVEL SUPERDISINTEGRANT

2019 ◽  
pp. 47-53
Author(s):  
R. SANTOSH KUMAR ◽  
KUMARI ANNU ◽  
B. KUSUMA LATHA ◽  
T. MALLIKA
Keyword(s):  
Drug Dissolution ◽  
In Vitro Dissolution ◽  
Disintegration Time ◽  
Drug Content ◽  
Enhanced Dissolution ◽  
Contour Plots ◽  
Wetting Time ◽  
Dissolution Efficiency ◽  
Tablet Preparation

Objective: The objective of the present research was to prepare starch phthalate (a novel super disintegrant) and to optimize and formulate ibuprofen fast dissolving tablets employing 23factorial design using starch phthalate as super disintegrant. Methods: Drug excipient compatibility studies like Fourier-transform infrared spectroscopy (FTIR) and thin-layer chromatography (TLC) studies were carried out to check the drug interaction between ibuprofen and starch phthalate. Direct compression method was used for tablet preparation. Prepared tablets were then evaluated for hardness, friability, drug content, disintegration time, water absorption and wetting time, in vitro dissolution studies. Response surface plots and contour plots were also plotted to know the main effects and interaction effects of independent variables (starch phthalate (A), croscarmellose sodium (B) and crospovidone (C)) on dependent variables (disintegration time and drug dissolution efficiency in 1 minute) and stability studies were also done. Results: Tablets of all formulations were of good quality concerning drug content (100±5%), hardness (3-6 kg/cm2), and friability (less than 0.16%). In all formulations, formulation F5 found to be optimized formulation with least disintegration time 20±0.28 seconds, less wetting time 09±0.12 seconds and enhanced dissolution rate in one minute, i.e., 91.95±0.22 as compared to other formulation. Conclusion: From the research, it was concluded that on combination with crospovidone, starch phthalate enhanced the dissolution efficiency of the drug. Hence, starch phthalate can be used as a novel disintegrant in the manufacturing of fast dissolving tablets.

scholarly journals FLASH DISSOLVING SUBLINGUAL ALMOTRIPTAN MALATE LYOTABS FOR MANAGEMENT OF MIGRAINE

2016 ◽  
Vol 9 (1) ◽  
pp. 125
Author(s):  
Abeer Ahmed Kassem ◽  
Gihan Salah Labib
Keyword(s):  
Crystalline Form ◽  
Scanning Calorimetry ◽  
Disintegration Time ◽  
Gastrointestinal Dysmotility ◽  
Bulk Forming ◽  
Ftir Studies ◽  
Wetting Time ◽  
Highly Porous

<p><strong>Objective: </strong>Development of sublingual fast dissolving lyophilized almotriptan tablets, to enhance its pre-gastric absorption and so alleviating the gastrointestinal dysmotility that is commonly associated with migraineurs.</p><p><strong>Methods: </strong>Primary almotriptan lyophilized tablets (Alm-lyotab), were prepared using polyvinyl alcohol (PVA), polyvinyl pyrrolidone (PVP), gelatin, or sodium alginate, as a bulk forming agent and mannitol as a disintegrant, cryoprotectant and taste improver. Physical properties, wetting time, <em>in vitro</em> dissolution and disintegration behaviour, were investigated. A combination of PVP, gelatin and chitosan in different ratios with mannitol were developed and characterised for further improvement. Optimised formula was examined by scanning electron microscope (SEM), differential scanning calorimetry (DSC) and Fourier-transform infrared spectroscopy (FTIR).</p><p><strong>Results: </strong>Both PVP and gelatin primary formulations showed elegant appearance with fast <em>in vitro</em> disintegration time of 5.67 and 5.64 sec, short wetting time of 4.06 and 4.05 sec, respectively, and high <em>in vitro</em> release rate of about 80% after 1 min, thus they were selected for further improvement. Optimised formula from polymer blend formulations (F8) which consisted of PVP: gelatin: chitosan in a ratio of its constituting solutions of 1:5:0.5, exhibited an elegant appearance, drug content of 98.75 %, <em>in vivo</em> disintegration time of 1.85 sec and complete drug release within 1 min. SEM micrographs revealed spongy, highly porous structure. DSC results indicated the presence of the drug in its crystalline form. FTIR studies revealed no interaction between the drug and excipients.</p><p><strong>Conclusion: </strong>Sublingual instantly dissolving Almo-lyotab was successfully developed and may constitute an advance in the management of acute migraine attacks.</p>

scholarly journals DESIGN, OPTIMIZATION, AND EVALUATION OF ACYCLOVIR FAST DISSOLVING TABLETS EMPLOYING STACH PHTHALATE – A NOVEL SUPERDISINTEGRANT

2019 ◽  
pp. 132-142 ◽  
Author(s):  
SANTOSH KUMAR R ◽  
ANNU KUMARI
Keyword(s):  
Drug Dissolution ◽  
In Vitro Dissolution ◽  
Scanning Calorimetry ◽  
Disintegration Time ◽  
Drug Content ◽  
Enhanced Dissolution ◽  
Wetting Time ◽  
Croscarmellose Sodium ◽  
Dissolution Efficiency

Objective: The objective of the present research was to prepare starch phthalate (a novel superdisintegrant) and to optimize and formulate acyclovir fast dissolving tablets employing 23 factorial design using starch phthalate as superdisintegrant. Materials and Methods: Drug excipient compatibility studies such as Fourier-transform infrared spectroscopy, differential scanning calorimetry, and thin-layer chromatography were carried out to check the drug interaction between acyclovir and starch phthalate. The direct compression method was used for tablet preparation. Prepared tablets were then evaluated for hardness, friability, drug content, disintegration time, water absorption, and wetting time, in vitro dissolution studies. Response surface plots and contour plots were also plotted to know the main effects and interaction effects of independent variables (starch phthalate [A], croscarmellose sodium [B], and crospovidone [C] on dependent variables [disintegration time and drug dissolution efficiency in 1 min]) and stability studies were also done. Results: Tablets of all formulations were of good quality concerning drug content (100±5%), hardness (3.6–4.0 kg/cm2), and friability (<0.16%). In all formulations, formulation F8 found to be optimized formulation with least disintegration time 9±3 s, less wetting time 10±0.17 s, and enhanced dissolution rate in 1 min, i.e., 99.92±0.11 as compared to other formulation. Conclusion: From the research, it was concluded that on combination with crospovidone (5%) and croscarmellose sodium (5%), starch phthalate (10%) enhanced the dissolution efficiency of the drug. Hence, starch phthalate can be used as a novel disintegrant in the manufacturing of fast dissolving tablets.

Preparation of cultured astrocytes for x-ray microanalysis

1989 ◽  
Vol 47 ◽  
pp. 988-989
Author(s):  
N.K.R. Smith ◽  
K.E. Hunter ◽  
P. Mobley ◽  
L.P. Felpel
Keyword(s):  
Cultured Cells ◽  
Elemental Content ◽  
Elemental Distribution ◽  
Sprague Dawley ◽  
X Ray ◽  
Cultured Astrocytes ◽  
Freeze Dried ◽  
Ultimate Objective

Electron probe energy dispersive x-ray microanalysis (XRMA) offers a powerful tool for the determination of intracellular elemental content of biological tissue. However, preparation of the tissue specimen , particularly excitable central nervous system (CNS) tissue , for XRMA is rather difficult, as dissection of a sample from the intact organism frequently results in artefacts in elemental distribution. To circumvent the problems inherent in the in vivo preparation, we turned to an in vitro preparation of astrocytes grown in tissue culture. However, preparations of in vitro samples offer a new and unique set of problems. Generally, cultured cells, growing in monolayer, must be harvested by either mechanical or enzymatic procedures, resulting in variable degrees of damage to the cells and compromised intracel1ular elemental distribution. The ultimate objective is to process and analyze unperturbed cells. With the objective of sparing others from some of the same efforts, we are reporting the considerable difficulties we have encountered in attempting to prepare astrocytes for XRMA.Tissue cultures of astrocytes from newborn C57 mice or Sprague Dawley rats were prepared and cultured by standard techniques, usually in T25 flasks, except as noted differently on Cytodex beads or on gelatin. After different preparative procedures, all samples were frozen on brass pins in liquid propane, stored in liquid nitrogen, cryosectioned (0.1 μm), freeze dried, and microanalyzed as previously reported.

Formulation and Evaluation of Fast Disintigrating Meloxicam Tablets and Its Comparison with Marketed Product

2010 ◽  
Vol 2 (2) ◽  
Author(s):  
Suresh Kulkarni ◽  
Ranjit P. ◽  
Nikunj Patel ◽  
Someshwara B. ◽  
Ramesh B. ◽  
...  
Keyword(s):  
Water Absorption ◽  
In Vitro Dissolution ◽  
Thickness Variation ◽  
Wet Granulation ◽  
Disintegration Time ◽  
Absorption Ratio ◽  
Wetting Time ◽  
Fast Disintegrating Tablets ◽  
Cox 1

The present investigation deals with the formulation of fast disintegrating tablets of Meloxicam that disintegrate in the oral cavity upon contact with saliva and there by improve therapeutic efficacy. Meloxicam is a newer selective COX-1 inhibitor. The tablets were prepared by wet granulation procedure. The influence of superdisintegrants, crosspovidone, croscaremellose sodium on disintegration time, wetting time and water absorption ratio were studied. Tablets were evaluated for weight and thickness variation, disintegration time, drug content, in vitro dissolution, wetting time and water absorption ratio. The in vitro disintegration time of the best fast disintegrating tablets was found to be 18 sec. Tablets containing crospovidone exhibit quick disintegration time than tablets containing croscaremellose sodium. The fast disintegrating tablets of Meloxicam with shorter disintegration time, acceptable taste and sufficient hardness could be prepared using crospovidone and other excipients at optimum concentration.

Design and In vivo Evaluation of Palonosetron HCl Mouth Dissolving Films in the Management of Chemotherapy-Induced Vomiting

2017 ◽  
Vol 10 (6) ◽  
pp. 3929-3936
Author(s):  
Y. Srinivasa Rao ◽  
K. Adinarayana Reddy
Keyword(s):  
Drug Release ◽  
Patient Compliance ◽  
Onset Of Action ◽  
In Vivo Evaluation ◽  
Disintegration Time ◽  
In Vitro Drug Release ◽  
Surface Ph ◽  
Drug Content

Fast dissolving oral delivery systems are solid dosage forms, which disintegrate or dissolve within 1 minute in the mouth without drinking water or chewing. Mouth dissolving film (MDF) is a better alternate to oral disintegrating tablets due to its novelty, ease of use and the consequent patient compliance. The purpose of this work was to develop mouth dissolving oral films of palonosetron HCl, an antiemetic drug especially used in the prevention and treatment of chemotherapy-induced nausea and vomiting. In the present work, the films were prepared by using solvent casting method with various polymers HPMC E3, E5 & E15 as a film base synthetic polymer, propylene glycol as a plasticizer and maltodextrin and other polymers. Films were found to be satisfactory when evaluated for thickness, in vitro drug release, folding endurance, drug content and disintegration time. The surface pH of all the films was found to be neutral. The in vitro drug release of optimized formulation F29 was found to be 99.55 ± 6.3 7% in 7 min. The optimized formulation F29 also showed satisfactory surface pH, drug content (99.38 ± 0.08 %), disintegration time of 8 seconds and good stability. FTIR data revealed that no interaction takes place between the drug and polymers used in the optimized formulation. In vitro and in vivo evaluation of the films confirmed their potential as an innovative dosage form to improve delivery and quick onset of action of Palonosetron Hydrochloride. Therefore, the mouth dissolving film of palonosetron is potentially useful for the treatment of emesis disease where quick onset of action is desired, also improved patient compliance.

Formulation and Evaluation of Orally Disintegrating Tablets of Lamotrigine

2015 ◽  
Vol 8 (2) ◽  
pp. 2881-2888
Author(s):  
Sudarshan Singh ◽  
S S Shyale ◽  
P Karade
Keyword(s):  
Drug Release ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Disintegration Time ◽  
Orally Disintegrating Tablet ◽  
Drug Content ◽  
Weight Variation ◽  
Wetting Time ◽  
Croscarmellose Sodium

The aim of this study was to design orally disintegrating tablet (ODT) of Lamotrigine. It is an Antiepileptic drug which is widely used in epilepsy. It is also used in simple and complex partial seizures and secondary generalized tonic-clonic seizures. It is poorly water soluble drug (0.46 mg/ml). Thus, an attempt was made to enhance the water solubility by complexation with β-cyclodextrin (1:1 molar ratios). The orally disintegrating tablet of lamotrigine was prepared by direct compression method using different concentration of superdisintegrants such as Sodium starch glycollate, croscarmellose sodium by sublimating agent such as camphor. The formulations were evaluated for weight variation, hardness, friability, drug content, wetting time, in vitro disintegration time and in vitro dissolution studies. The prepared tablets were characterized by Fourier transform infrared spectroscopy and differential scanning calorimetry. The disintegration time for the complexed tablets prepared by different concentration of superdisintegrants was found to be in range of 32.54 ± 0.50 to 55.12 ± 0.57 sec and wetting time of the formulations was found to be in range of 28.47 ± 0.67 to 52.19 ± 0.72 sec. All the formulation showed almost 100 percent of drug release within 15 min. Among all the formulation F6 and F7 prepared with 18% croscarmellose sodium and camphor shows faster drug release, respectively 10 min, F6 gives good result for disintegration time, drug release, wetting time and friability. Further formulations were subjected to stability testing for 30 days at temperature of 40 ± 5 ºC/75 ± 5 %RH. Tablets showed no appreciable changes with respect to physical appearance, drug content, disintegration time and dissolution profiles. Results were statistically analyzed by one-way ANOVA at a p < 0.05. It was found that, the data at any point of time are significant at p < 0.05.

Freeze-Dried Clopidogrel Loaded Lyotropic Liquid Crystal: Box-Behnken Optimization, In-Vitro and In-Vivo Evaluation

2020 ◽  
Vol 17 (3) ◽  
pp. 207-217
Author(s):  
Eman A. Hakeem ◽  
Galal M. El-Mahrouk ◽  
Ghada Abdelbary ◽  
Mahmoud H. Teaima
Keyword(s):  
Statistical Analysis ◽  
Oral Bioavailability ◽  
Quadratic Model ◽  
Lipid Phase ◽  
Individual Response ◽  
In Vivo Evaluation ◽  
Freeze Dried ◽  
Suggested Formula

Background: Clopidogrel (CLP) suffers from extensive first pass metabolism results in a negative impact on its oral systemic bioavailability. Cubosomes are Lyotropic Liquid Crystalline (LLC) nano-systems comprising monoolein, a steric stabilizer and an aqueous system, it considered a promising carrier for different pharmaceutical compounds. Box-Behnken Design (BBD) is an efficient tool for process analysis and optimization skipping forceful treatment combinations. Objective: The study was designed to develop freeze-dried clopidogrel loaded LLC (cubosomes) for enhancement of its oral bioavailability. Methods: A 33 BBD was adopted, the studied independent factors were glyceryl monooleate (GMO lipid phase), Pluronic F127 (PL F127steric stabilizer) and polyvinyl alcohol powder (stabilizer). Particle Size (PS), Polydispersity Index (PDI) and Zeta Potential (ZP) were set as independent response variables. Seventeen formulae were prepared in accordance with the bottom up approach and in-vitro evaluated regarding PS, PDI and ZP. Statistical analysis and optimization were achieved using design expert software®, then the optimum suggested formula was prepared, in-vitro revaluated, freeze-dried with 3% mannitol (cryoprotectant), solid state characterized and finally packed in hard gelatin capsule for comparative in-vitro release and in-vivo evaluation to Plavix®. Results: Results of statistical analysis of each individual response revealed a quadratic model for PS and PDI where a linear model for ZP. The optimum suggested formula with desirability factor equal 0.990 consisting of (200 mg GMO, 78.15 mg PL F127 and 2% PVA). LC/MS/MS study confirmed significant higher C>max, AUC>0-24h and AUC>0-∞ than that of Plavix®. Conclusion: The results confirm the capability of developed carrier to overcome the low oral bioavailability.

scholarly journals DESIGN, OPTIMIZATION AND EVALUATION OF CETRIZINE DIHYDROCHLORIDE FAST DISSOLVING FILMS EMPLOYING STARCH TARTRATE–A NOVEL SUPERDISINTEGRANT

2019 ◽  
pp. 75-86
Author(s):  
R. SANTOSH KUMAR ◽  
ANNU KUMARI ◽  
B. KUSUMA LATHA ◽  
PRUDHVI RAJ
Keyword(s):  
Tensile Strength ◽  
Drug Dissolution ◽  
In Vitro Dissolution ◽  
Content Uniformity ◽  
Scanning Calorimetry ◽  
Disintegration Time ◽  
Folding Endurance ◽  
Contour Plots ◽  
The Individual

Objective: The aim of the current research is optimization, preparation and evaluation of starch tartrate (novel super disintegrant) and preparation of fast dissolving oral films of cetirizine dihydrochloride by employing starch tartrate. Methods: To check the drug excipient compatibility studies of the selected drug (Cetrizine dihydrochloride) and the prepared excipient i. e starch tartrate, different studies like FTIR (Fourier-transform infrared spectroscopy), DSC (Differential scanning calorimetry) and thin-layer chromatography (TLC) were carried out to find out whether there is any interaction between cetirizine dihydrochloride and starch tartrate. The solvent casting method was used for the preparation of fast dissolving films. The prepared films were then evaluated for thickness, folding endurance, content uniformity, tensile strength, percent elongation, in vitro disintegration time and in-vitro dissolution studies. Response surface plots and contour plots were also plotted to know the individual and combined effect of starch tartrate (A), croscarmellose sodium (B) and crospovidone (C) on disintegration time and drug dissolution efficiency in 10 min (dependent variables). Results: Films of all the formulations are of good quality, smooth and elegant by appearance. Drug content (100±5%), thickness (0.059 mm to 0.061 mm), the weight of films varies from 51.33 to 58.06 mg, folding endurance (52 to 67 times), tensile strength (10.25 to 12.08 N/mm2). Fast dissolving films were found to disintegrate between 34 to 69 sec. Percent dissolved in 5 min were found to be more in F1 formulation which confirms that starch tartrate was effective at 1%. Conclusion: From the research conducted, it was proved that starch tartrate can be used in the formulation of fast dissolving films of cetirizine dihydrochloride. The disintegration time of the films was increased with increase in concentration of super disintegrant.

Sign in / Sign up

Export Citation Format

Share Document