Structure changes of high-strength economically alloyed steel 09KhGN2MD (09CrMnNi2MoCu) when tempering

2019 ◽  
pp. 15-26 ◽  
Author(s):  
M. V. Golubeva ◽  
O. V. Sych ◽  
E. I. Khlusova ◽  
G. D. Motovilina ◽  
E. V. Sviatysheva ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Fracture Mode ◽  
High Strength ◽  
Resistant Steel ◽  
Optimal Heat ◽  
Optimal Heat Treatment ◽  
Structure Changes ◽  
The Relationship ◽  
Quenching And Tempering

Purpose of the present investigation is to determine the optimal heat treatment parameters that ensure yield strength over 690 MPa in combination with toughness of at least 35 J/cm2at temperature –70°C in new economically alloyed cold-resistant steel. The effect of various quenching and tempering parameters on mechanical properties, structure of steel and fracture mode of samples after impact tests at temperature –70°C has been studied. The relationship between the properties, structure and fracture mode of steel samples is shown. The optimal heat treatment parameters of new economically alloyed cold-resistant steel are determined.

Mechanical Properties of a Mild-Alloy Steel for Aerospace Engineering

2021 ◽  
Vol 410 ◽  
pp. 221-226
Author(s):  
Mikhail V. Maisuradze ◽  
Maxim A. Ryzhkov ◽  
Dmitriy I. Lebedev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Aerospace Engineering ◽  
Isothermal Heat Treatment ◽  
Tempering Temperature ◽  
Optimal Heat Treatment ◽  
Treatment Conditions ◽  
Quenching And Tempering ◽  
Conventional Oil

The features of microstructure and mechanical properties of the aerospace high strength steel were studied after the implementation of various heat treatment modes: conventional oil quenching and tempering, quenching-partitioning, austempering. The dependence of the mechanical properties on the tempering temperature was determined. The basic patterns of the formation of mechanical properties during the implementation of isothermal heat treatment were considered. The optimal heat treatment conditions for the studied steel were established.

Microstructure and Mechanical Properties of High Strength Alloyed Steel for Aerospace Application

2018 ◽  
Vol 284 ◽  
pp. 351-356 ◽  
Author(s):  
Mikhail V. Maisuradze ◽  
Maksim A. Ryzhkov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Single Stage ◽  
The Novel ◽  
Tempering Temperature ◽  
Quenching And Partitioning ◽  
Aerospace Application ◽  
Cooling Conditions ◽  
Quenching And Tempering

The high strength aerospace steel alloyed with Cr, Mn, Si, Ni, W and Mo was studied. The austenite transformations under continuous cooling conditions were investigated using the dilatometer analysis at the cooling rates 0.1...30 °C/s. The mechanical properties of the studied steel were determined after the conventional quenching and tempering heat treatment. The dependences of the mechanical properties on the tempering temperature were obtained. The novel quenching and partitioning heat treatment was applied to the steel under consideration. The microstructure and the mechanical properties were studied after three different modes of the quenching and partitioning (QP) treatment: single-stage QP, two-stage QP and single-stage QP with subsequent tempering (QPT).

Effect of Different Heat Treatments on Microstructure and Mechanical Properties of the Martensitic Gx12CrMoVNbN9-1 Cast Steel / Wpływ Parametrów Obróbki Cieplnej Na Mikrostrukture I Własciwosci Mechaniczne Martenzytycznego Staliwa Gx12CrMoVNbn9-1

2013 ◽  
Vol 58 (1) ◽  
pp. 25-30 ◽  
Author(s):  
G. Golanski ◽  
J. Słania
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Impact Energy ◽  
Cast Steel ◽  
Lath Martensite ◽  
High Strength ◽  
Strength Properties ◽  
Microstructure And Mechanical Properties ◽  
Quenching And Tempering ◽  
Very High

The paper presents a research on the influence of multistage heat treatment with the assumed parameters of temperature and time on the microstructure and mechanical properties of high-chromium martensitic GX12CrMoVNbN9-1 (GP91) cast steel. In the as-cast state GP91 cast steel was characterized by a microstructure of lath martensite with numerous precipitations of carbides of the M23C6, M3C and NbC type, with its properties higher than the required minimum. Hardening of the examined cast steel contributes to obtaining a microstructure of partly auto-tempered martensite of very high strength properties and impact strength KV on the level of 9-15 J. Quenching and tempering with subsequent stress relief annealing of GP91 cast steel contributed to obtaining the microstructure of high-tempered lath martensite with numerous precipitations of the M23C6 and MX type of diverse size. The microstructure of GP91 cast steel received after heat treatment was characterized by strength properties (yield strength, tensile strength) higher than the required minimum and a very high impact energy KV. It has been proved that GP91 cast steel subject to heat treatment No. 2 as a result of two-time heating above the Ac3 temperature is characterized by the highest impact energy.

Phase Transformations in D6AC Steel during Continuous Cooling

2017 ◽  
Vol 265 ◽  
pp. 712-716 ◽  
Author(s):  
Mikhail V. Maisuradze ◽  
Maksim Ryzhkov ◽  
Aleksandra A. Kuklina
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Transformations ◽  
High Strength ◽  
Treatment Technology ◽  
Heat Treatment Technology ◽  
Cooling Conditions ◽  
Drill Bits ◽  
Steel Drill ◽  
Quenching And Tempering

The CCT diagram of the high strength D6AC steel was plotted using the dilatometer data, microstructure investigation, and hardness measurements. The microstructure of the steel under consideration was estimated after various cooling conditions and quenching and tempering. The heat treatment technology of D6AC steel drill bits was developed to obtain the required mechanical properties.

The effect of microalloying on mechanical properties of low-carbon chromium-nickel-molybdenum steel

2019 ◽  
pp. 7-14
Author(s):  
S. A. Golosienko ◽  
N. A. Minyakin ◽  
V. V. Ryabov ◽  
T. G. Semicheva ◽  
E. I. Khlusova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Yield Strength ◽  
High Strength ◽  
Low Carbon ◽  
High Toughness ◽  
Thermal Improvement ◽  
Molybdenum Steel ◽  
Quenching And Tempering ◽  
Rolling Heat

The work covers the effect of niobium, as well as niobium and vanadium together, on mechanical properties of high-strength chromium-nickel-molybdenum steel after thermal improvement (heat treatment). The mechanical properties of steels are determined after applying various tempering temperatures (from 580 to 660°C), durations of tempering (from 1 to 16 hours), and also after quenching from rolling heat and furnace heat with subsequent tempering. It is shown that after quenching and tempering in the temperature range 580– 660°C, simultaneous microalloying by niobium and vanadium, compared to microalloying by niobium alone, increases the yield strength but in significantly decreases toughness and ductility. Quenching from rolling heat increases strength while maintaining high toughness and the increase in strength is most noticeable for steel microalloyed only by niobium.

Effect of Heat Treatment on Mechanical Properties of 1500MPa High Strength Wear-Resistant Steel

2010 ◽  
Vol 168-170 ◽  
pp. 847-851 ◽  
Author(s):  
Kai Liu ◽  
Jin Jin Zhang ◽  
Kai Ming Wu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Electron Microscope ◽  
High Strength ◽  
Resistant Steel ◽  
Tempering Temperature ◽  
Wear Resistant ◽  
Obvious Change

A high strength low alloy wear-resistant steel was quenched at 900°C and tempered at varying temperatures. The microstructures were observed utilizing optical and electron microscope. Results show that microstructures consist of predominantly martensite and lots of bainite in the as-quenched specimens. When the specimen was tempered at 250°C, no obvious change in the microstructure was observed. It has an optimized strength and elongation in this condition of heat treatment. With the increase of tempering temperature, the lath or plate of martensite were coalescenced. The strength of the steel is thus greatly reduced and the elongation was accordingly increased.

The influence of heat treatment on the formation of the structure and the level of mechanical properties of high-alloyed titanium alloy

2020 ◽  
pp. 28-41
Author(s):  
I. R. Kozlova ◽  
E. V. Chudakov ◽  
N. V. Tretyakova ◽  
Yu. M. Markova ◽  
E. A. Vasilieva
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
Thermal Action ◽  
High Strength ◽  
Heterogeneous Structure ◽  
Two Phase ◽  
Structure Changes ◽  
Hardened State ◽  
Alloyed Titanium

The paper investigates the possibility of increasing the strength of the experimental high-alloyed titanium alloy due to various methods of thermal action, leading to a change in its phase composition and intragrain structure. Changes in mechanical properties in correlation with the change in structure in the annealed, tempered and heat-hardened state are reviewed. It is shown that by controlling phase transformations in highalloyed two-phase titanium alloys, it is possible to realize high-strength state with satisfactory plastic characteristics. The optimal complex of mechanical properties is provided by heat treatment, which leads to the creation of a two-phase heterogeneous structure with a developed bimodal intragrain structure.

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

UNS A97075

Alloy Digest ◽  
1986 ◽  
Vol 35 (7) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Good Resistance ◽  
Temperature Performance ◽  
Structural Applications ◽  
Structural Parts ◽  
Very High

Abstract UNS No. A97075 is a wrought precipitation-hardenable aluminum alloy. It has excellent mechanical properties, workability and response to heat treatment and refrigeration. Its typical uses comprise aircraft structural parts and other highly stressed structural applications where very high strength and good resistance to corrosion are required. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on low temperature performance as well as forming, heat treating, and machining. Filing Code: Al-269. Producer or source: Various aluminum companies.

Sign in / Sign up

Export Citation Format

Share Document