Microstructure and Mechanical Properties of Cast and Hot-Rolled Medium-Carbon Steels under Isothermal Heat-Treatment Conditions

In this study, the changes in the microstructure and mechanical properties during isothermal heat treatment of cast steel before and after hot deformation were investigated using medium-carbon steel with low alloy content. The microstructural characteristics of the cast and hot-rolled medium-carbon steel under isothermal heat-treatment conditions were examined using optical microscopy and scanning electron microscopy in conjunction with electron backscatter diffraction. The variation in the mechanical properties was evaluated using Rockwell hardness and tensile tests. After maintaining an austenitizing condition at 1200 °C for 30 min, an isothermal heat treatment was performed in the range 350–500 °C, followed by rapid cooling with water. Both the cast steel and hot-rolled steel did not completely transform into bainitic ferrite during isothermal heat treatment. The partially untransformed microstructure was a mixture of martensite and acicular ferrite. At 500 °C, the prior austenite phase changed to Widmanstätten ferrite and pearlite. At 450 °C, bainitic ferrite and cementite were coarsened by the coalescence of ferrite and subsequent diffusive growth. The mechanical properties increased as the isothermal heat-treatment temperature decreased, and the hardness of the cast steel was generally higher than that of the hot-rolled steel. Hardness and strength showed similar trends, and overall mechanical properties tend to decrease as the isothermal heat-treatment temperature increases, but there are slight differences depending on complex factors such as various phase fractions and grain size.

Study of Grain Growth in a Ni-Based Superalloy by Experiments and Cellular Automaton Model

The grain growth behavior in a typical Ni-based superalloy was investigated using isothermal heat treatment experiments over a holding temperature range of 1353–1473 K. The experimental results showed that the grain structure continuously coarsened as the holding time and holding temperature increased during heat treatment. A classical parabolic grain growth model was used to explore the mechanism of grain growth under experimental conditions. The grain growth exponent was found to be slightly above 2. This indicates that the current grain growth in the studied superalloy is mainly governed by grain boundary migration with a minor pinning effect from the precipitates. Then, the grain growth in the studied superalloy during isothermal heat treatment was modelled by a cellular automaton (CA) with deterministic state switch rules. The microscale kinetics of grain growth is described by the correlation between the moving velocity and curvature of the grain boundary. The local grain boundary curvature is well evaluated by a template disk method. The grain boundary mobility was found to increase with increasing temperature. The relationship between the grain boundary mobility and temperature has been established. The developed CA model is capable of capturing the dependence of the grain size on the holding time under different holding temperatures.

Influence of Si and Al contents and isothermal treatment condition on the microstructure and tensile properties in ultra-high strength Fe-0.2C-2.0Mn martensite-bainite complex phase steels

This study investigated the influence of partial replacement of Si by Al on the microstructure and tensile properties of ultra-high strength steels with martensite-bainite complex microstructure produced by austenitization and subsequent isothermal heat treatment around Ms temperature. When the isothermal heat treatment was done below the Ms temperature, the fraction of martensite increased with the lower isothermal temperature, but the fractions of constituent phases in the final microstructure were not significantly affected by the partial replacement of Si by Al. Nevertheless, the increase in Al content in the complex phase steel accelerated the bainite transformation, which is thought to be associated with the increase of the free energy difference between FCC and BCC. The enhancement of the bainite transformation not only effectively suppressed the martensite formation upon final cooling when the isothermal temperature was above the Ms temperature but also helped refine the final microstructure when subjected to isothermal heat treatment below the Ms temperature. The yield strengths of the investigated complex phase steels were little influenced by the partial replacement of Si with Al, as long as the fractions of the constituent phases were comparable. This possibly originates with the solid solution hardening and the microstructure refinement with Al addition.

Mechanical Properties of a Mild-Alloy Steel for Aerospace Engineering

The features of microstructure and mechanical properties of the aerospace high strength steel were studied after the implementation of various heat treatment modes: conventional oil quenching and tempering, quenching-partitioning, austempering. The dependence of the mechanical properties on the tempering temperature was determined. The basic patterns of the formation of mechanical properties during the implementation of isothermal heat treatment were considered. The optimal heat treatment conditions for the studied steel were established.

Mathematical Modelling of Isothermal Decomposition ofAustenite in Steel

The main goal of this paper is mathematical modelling and computer simulation of isothermal decomposition of austenite in steel. Mathematical modelling and computer simulation of isothermal decomposition of austenite nowadays is becoming an indispensable tool for the prediction of isothermal heat treatment results of steel. Besides that, the prediction of isothermal decomposition of austenite can be applied for understanding, optimization and control of microstructure composition and mechanical properties of steel. Isothermal decomposition of austenite is physically one of the most complex engineering processes. In this paper, methods for setting the kinetic expressions for prediction of isothermal decomposition of austenite into ferrite, pearlite or bainite were proposed. After that, based on the chemical composition of hypoeutectoid steels, the quantification of the parameters involved in kinetic expressions was performed. The established kinetic equations were applied in the prediction of microstructure composition of hypoeutectoid steels.