RESEARCH ON CUTTING FORCES AND CUTTING TEMPERATURE IN ORTHOGONAL CUTTING SOFTWOOD AND HARDWOOD PARALLEL TO GRAIN

2018 ◽  
Vol 50 (4) ◽  
pp. 458-464
Author(s):  
Xu Bao ◽  
Xiaolei Guo ◽  
Pingxiang Cao ◽  
Linlin Xie ◽  
Minsi Deng
Keyword(s):  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Cutting Temperature

Effect of Tool Flank Wear on the Orthogonal Cutting Process

2007 ◽  
Vol 329 ◽  
pp. 705-710 ◽  
Author(s):  
X.L. Zhao ◽  
Yong Tang ◽  
Wen Jun Deng ◽  
F.Y. Zhang
Keyword(s):  
Cutting Forces ◽  
Cutting Tool ◽  
Flank Wear ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Element Model ◽  
Cutting Process ◽  
Temperature Fields ◽  
Tool Flank Wear ◽  
Chip Separation

A coupled thermoelastic-plastic plane-strain finite element model is developed to study orthogonal cutting process with and without flank wear. The cutting process is simulated from the initial to the steady-state of cutting force and cutting temperature, by incrementally advancing the cutting tool forward. Automatic continuous remeshing is employed to achieve chip separation at the tool tip regime. The effect of the degree of the flank wear on the cutting forces and temperature fields is analyzed. With the flank wear increasing, the maximum cutting temperature values on the workpiece and cutting tool increase rapidly and the distribution of temperature changes greatly. The increase of tool flank wear produced slight increase in cutting forces but significant increase in thrust forces.

Experimental Research on Orthogonal Cutting and Oblique Cutting of Hardened Steel GCr15

2008 ◽  
Vol 375-376 ◽  
pp. 192-196 ◽  
Author(s):  
Yu Wang ◽  
Peng Wang ◽  
Hong Min Pen ◽  
Yu Fu Li ◽  
Xian Li Liu
Keyword(s):  
Inclination Angle ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Three Dimensional ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Shear Zones ◽  
Feed Speed ◽  
Oblique Cutting ◽  
Strain And Strain Rate

Experiment of hard cutting GCr15 with PCBN cutting tools, the influence of tool’s inclination angle and cutting parameters (cutting speed and feed speed) on cutting forces and cutting temperature are studied. A three-dimensional finite elements model using the commercial software Deform 3D 5.03 is developed. The friction between the tool and the chip is assumed to follow a modified Coulomb friction law and the adaptive remeshing technique is using for the formation of chip. The workpiece material property is a function of temperature, strain, and strain rate in the primary and secondary shear zones. Finite element method is used to simulate three-dimensional precision cutting, including orthogonal cutting and oblique cutting. The cutting forces and back forces are slightly changed by tool’s inclination angle. However, in high cutting speed, the cutting force decrease as the tool’s inclination angle increase, while the cutting temperature increase as the tool’s inclination angle increase. The simulation results are compared with experimentally measured data and found to be in good agreement to some extent.

Numerical Modeling the Effect of Tool-Chip Friction in Orthogonal Cutting AISI4340

2010 ◽  
Vol 29-32 ◽  
pp. 1815-1819 ◽  
Author(s):  
Gang Tao Xu ◽  
Yu Sheng Li
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Cutting Forces ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Clear Understanding ◽  
Workpiece Material ◽  
Explicit Finite Element ◽  
Plastic Model

A thermo-elastic-plastic model using explicit finite element code ABAQUS 6.8 was developed to investigate the effect of tool-chip friction in orthogonal cutting AISI4340. A.L.E finite element model was presented and the Johnson-Cook plastic model was used to model the workpiece material which is suitable for modeling cases with high strain, strain rate, strain hardening, and non-linear properties. In this paper, three different friction coefficient values of 0.2, 0.3, 0.4 were considered to study the effect on Cutting temperature, cutting forces and cutting stress. The results told a clear understanding of the effect of friction coefficient in orthogonal metal cutting, and larger friction coefficient induced higher cutting temperature, bigger cutting forces and larger cutting stress.

scholarly journals Influence of tool edge form factor and cutting parameters on milling performance

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110090
Author(s):  
Xuefeng Zhao ◽  
Hao Qin ◽  
Zhiguo Feng
Keyword(s):  
Form Factor ◽  
Simulation Model ◽  
Cutting Force ◽  
Surface Quality ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Tool Edge ◽  
Drag Finishing ◽  
Edge Preparation

Tool edge preparation can improve the tool life, as well as cutting performance and machined surface quality, meeting the requirements of high-speed and high-efficiency cutting. In general, prepared tool edges could be divided into symmetric or asymmetric edges. In the present study, the cemented carbide tools were initially edge prepared through drag finishing. The simulation model of the carbide cemented tool milling steel was established through Deform software. Effects of edge form factor, spindle speed, feed per tooth, axial, and radial cutting depth on the cutting force, the tool wear, the cutting temperature, and the surface quality were investigated through the orthogonal cutting simulation. The simulated cutting force results were compared to the results obtained from the orthogonal milling experiment through the dynamometer Kistler, which verified the simulation model correctness. The obtained results provided a basis for edge preparation effect along with high-speed and high effective cutting machining comprehension.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Predicting the High Speed Cutting Process of Titanium Alloy by Finite Element Method

2011 ◽  
Author(s):  
Xiangqin Zhang ◽  
Xueping Zhang ◽  
A. K. Srivastava
Keyword(s):  
Finite Element ◽  
Cutting Forces ◽  
High Speed ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
Cutting Process ◽  
Fe Model ◽  
Dry Cutting ◽  
Friction Coefficients ◽  
Machining Conditions

To predict the cutting forces and cutting temperatures accurately in high speed dry cutting Ti-6Al-4V alloy, a Finite Element (FE) model is established based on ABAQUS. The tool-chip-work friction coefficients are calculated analytically using the measured cutting forces and chip morphology parameter obtained by conducting the orthogonal (2-D) machining tests. It reveals that the friction coefficients between tool-work are 3∼7 times larger than that between tool-chip, and the friction coefficients of tool-chip-work vary with feed rates. The analysis provides a better reference for the tool-work-chip friction coefficients than that given by literature empirically regardless of machining conditions. The FE model is capable of effectively simulating the high speed dry cutting process of Ti-6Al-4V alloy based on the modified Johnson-Cook model and tool-work-chip friction coefficients obtained analytically. The FE model is further validated in terms of predicted forces and the chip morphology. The predicted cutting force, thrust force and resultant force by the FE model agree well with the experimentally measured forces. The errors in terms of the predicted average value of chip pitch and the distance between chip valley and chip peak are smaller. The FE model further predicts the cutting temperature and residual stresses during high speed dry cutting of Ti-6Al-4V alloy. The maximum tool temperatures exist along the round tool edge, and the residual stress profiles along the machined surface are hook-shaped regardless of machining conditions.

Monitoring of Cutting Conditions with Dry Cutting on CNC Turning Machine

2010 ◽  
Vol 443 ◽  
pp. 382-387 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Suthas Ratanakuakangwan
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Temperature ◽  
Cutting Conditions ◽  
Cutting Condition ◽  
Nose Radius ◽  
Dry Cutting ◽  
Cnc Turning ◽  
Coated Carbide

This paper presents the additional work of the previous research in order to verify the previously obtained cutting condition by using the different cutting tool geometries. The effects of the cutting conditions with the dry cutting are monitored to obtain the proper cutting condition for the plain carbon steel with the coated carbide tool based on the consideration of the surface roughness and the tool life. The dynamometer is employed and installed on the turret of CNC turning machine to measure the in-process cutting forces. The in-process cutting forces are used to analyze the cutting temperature, the tool wear and the surface roughness. The experimentally obtained results show that the surface roughness and the tool wear can be well explained by the in-process cutting forces. Referring to the criteria, the experimentally obtained proper cutting condition is the same with the previous research except the rake angle and the tool nose radius.

scholarly journals Analytical modelling of cutting forces in near-orthogonal cutting of titanium alloy Ti6Al4V

2014 ◽  
Vol 229 (6) ◽  
pp. 1122-1133 ◽  
Author(s):  
Yun Chen ◽  
Huaizhong Li ◽  
Jun Wang
Keyword(s):  
Titanium Alloy ◽  
Cutting Forces ◽  
Chemical Reactivity ◽  
Orthogonal Cutting ◽  
Chip Thickness ◽  
Analytical Modelling ◽  
Shear Instability ◽  
Published Data ◽  
Machining Processes ◽  
Titanium Alloy Ti6al4v

Titanium and its alloys are difficult to machine due to their high chemical reactivity with tool materials and low thermal conductivity. Chip segmentation caused by the thermoplastic instability is always observed in titanium machining processes, which leads to varied cutting forces and chip thickness, etc. This paper presents an analytical modelling approach for cutting forces in near-orthogonal cutting of titanium alloy Ti6Al4V. The catastrophic shear instability in the primary shear plane is assumed as a semi-static process. An analytical approach is used to evaluate chip thicknesses and forces in the near-orthogonal cutting process. The shear flow stress of the material is modelled by using the Johnson–Cook constitutive material law where the strain hardening, strain rate sensitivity and thermal softening behaviours are coupled. The thermal equations with non-uniform heat partitions along the tool–chip interface are solved by a finite difference method. The model prediction is verified with experimental data, where a good agreement in terms of the average cutting forces and chip thickness is shown. A comparison of the predicted temperatures with published data obtained by using the finite element method is also presented.

Analytical cutting force modelling of micro-slot grinding considering tool-workpiece interactions on both primary and secondary tool surfaces

2021 ◽  
pp. 1-43
Author(s):  
Ashwani Pratap ◽  
Karali Patra
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Surface Interactions ◽  
Surface Interaction ◽  
Edge Density ◽  
Force Model ◽  
Height Distribution ◽  
Force Modeling ◽  
Tool Surface

Abstract This work presents an analytical cutting force modeling for micro-slot grinding. Contribution of the work lies in the consideration of both primary and secondary tool surface interactions with the work surface as compared to the previous works where only primary tool surface interaction was considered during cutting force modeling. Tool secondary surface interaction with workpiece is divided into two parts: cutting/ ploughing by abrasive grits present in exterior margin of the secondary tool surface and sliding/adhesion by abrasive grits in the inner margins of the secondary tool surface. Orthogonal cutting force model and indentation based fracture model is considered for cutting by both the abrasives of primary tool surface and the abrasives of exterior margin on the secondary surface. Asperity level sliding and adhesion model is adopted to solve the interaction between the workpiece and the interior margin abrasives of secondary tool surface. Experimental measurement of polycrystalline diamond tool surface topography is carried out and surface data is processed with image processing tools to determine the tool surface statistics viz., cutting edge density, grit height distribution and abrasive grit geometrical measures. Micro-slot grinding experiments are carried out on BK7 glass at varying feed rate and axial depths of cut to validate the simulated cutting forces. Simulated cutting forces considering both primary and secondary tool surface interactions are found to be much closer to the experimental cutting forces as compared to the simulated cutting forces considering only primary tool surface interaction.

A Metallo-Thermomechanically Coupled Analysis of Orthogonal Cutting of AISI 1045 Steel

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hongtao Ding ◽  
Yung C. Shin
Keyword(s):  
Experimental Data ◽  
Cutting Force ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
Machining Process ◽  
Coupled Analysis ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

Materials often behave in a complicated manner involving deeply coupled effects among stress/stain, temperature, and microstructure during a machining process. This paper is concerned with prediction of the phase change effect on orthogonal cutting of American Iron and Steel Institute (AISI) 1045 steel based on a true metallo-thermomechanical coupled analysis. A metallo-thermomechanical coupled material model is developed and a finite element model (FEM) is used to solve the evolution of phase constituents, cutting temperature, chip morphology, and cutting force simultaneously using abaqus. The model validity is assessed using the experimental data for orthogonal cutting of AISI 1045 steel under various conditions, with cutting speeds ranging from 198 to 879 m/min, feeds from 0.1 to 0.3 mm, and tool rake angles from −7 deg to 5 deg. A good agreement is achieved in chip formation, cutting force, and cutting temperature between the model predictions and the experimental data.

Sign in / Sign up

Export Citation Format

Share Document