scholarly journals PENGARUH ORIENTASI OBJEK PADA PROSES 3D PRINTING BAHAN POLYMER PLA DAN ABS TERHADAP KEKUATAN TARIK DAN KETELITIAN DIMENSI PRODUK

SINERGI ◽  
2016 ◽  
Vol 20 (1) ◽  
pp. 27
Author(s):  
Sobron Lubis ◽  
Sofyan Djamil ◽  
Yolanda Yolanda
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
3D Printer ◽  
Layer Material

Penelitian ini dilaksanakan untuk mengetahui pengaruh posisi objek dalam pembuatan protipe cepat (rapid prototyping) dengan menggunakan 3D printing untuk bahan polymer PLA dan ABS terhadap kekuatan tarik maupun ketelitian dimensi yang dihasilkan. Untuk  mencapai objektif penelitian ini dilakukan percobaan dengan membuat prototype spesimen ujitarik berdasarkan ASTM dengan menggunakan 3D printer. Produk yang dihasilkan dilakukan pengukuran dimensi untuk melihat akurasi peroduk melalui perubahan dua posisi variasi orientasi objek yakni secara vertikal dan horizontal. Setelah proses pengukuran dimensi, dilakukan pengujian tarik spesimen dengan menggunakan alat uji tarik. Dari eksperimen yang dilakukan diketahui bahwa posisi orientasi dan besar layer pada proses printing memberi efek terhadap kualitas permukaan, efisiensi waktu dan kekuatan dari benda. Produk material PLA dengan orientasi posisi objek horizontal memiliki kualitas dimensi yang paling baik. Jumlah kesalahan akurasi material ini tidak melebihi 1 mm pada setiap layer. Material ABS dengan posisi orientasi objek  vertikal dan tebal layer sebesar 0,10 mm menghasilkan kekuatan tegangan tarik yang terkecil sebesar 8,62 MPa dan material PLA dengan orientasi posisi objek horizontal dengan dan tebal layer sebesar 0,40 mm menghasilkan kekuatan tegangan tarik terbesar 35,57 MPa

Bend Testing of Parts Made by Rapid Prototyping with Respect to Possible Use in Robotics

2015 ◽  
Vol 760 ◽  
pp. 141-146 ◽  
Author(s):  
Jan Lipina ◽  
Václav Krys ◽  
Jiří Marek
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Experimental Determination ◽  
Internal Structure ◽  
Detailed Knowledge ◽  
3D Printer ◽  
Bend Strength ◽  
Bend Testing ◽  
Material Parameters

Recently, the Rapid Prototyping technology (RP hereafter) has been increasingly used for a final product, which requires detailed knowledge of designing parts made by the RP technology. In order to apply parts made by the RP technology in robotics, and design in general, in a wider range, one of the most important material parameters is their bend strength. The paper describes an experimental determination of bend strength in parts printed on a 3D printer. The parts were made of polycarbonate. The tests were carried out in parts with various types of internal structure. The achieved results can be implemented when designing parts made by 3D printing provided that professional printers are used.

scholarly journals Analisis Pada Proses 3d Printer Terhadap Pengujian Tarik Menggunakan Filamen Pla Pro

2021 ◽  
Vol 2 (12) ◽  
pp. 2107-2117
Author(s):  
Riskullah Dirga Trisaplin ◽  
Zaldy Sirwansyah Suzen ◽  
Subkhan Subkhan
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Rapid Prototyping ◽  
3D Printer ◽  
Nozzle Temperature

Hadirnya Revolusi Industri 4.0 menyebabkan teknologi di bidang industri manufaktur berkembang sangat pesat, salah satunya mesin Rapid Prototyping dengan teknologi FDM yang merupakan mesin cetak 3 dimensi dengan prinsip pencetakan secara additive manufacturing informasi mengenai parameter proses yang dapat menghasilkan suatu produk 3D dengan kekuatan tarik secara ideal di Indonesia sangat minim, mengingat informasi tersebut sangat diperlukan dunia industri, sehingga penelitian ini bertujuan untuk mengetahui nilai kekuatan tarik serta parameter proses yang ideal dengan menggunakan filamen PLA PRO Metode yang digunakan pada penelitian ini adalah metode eksperimen faktorial, penelitian ini menggunakan mesin 3D printer Anet Et4, nozzle berukuran 0,4 mm, variasi parameter yang digunakan yaitu 3 level nozzle temperature, 15 infill pattern berdasarkan software Prusaslicer 2.3 dan orientasi sudut pencetakan vertikal 90ᵒ. Sehingga menghasilkan 45 kombinasi eksperimen. Hasil dari pengujian tarik tertinggi sebesar 44,2 yang terdapat pada eksperimen nomor 10 infill pattern 3D Honeycomb, Nozzle Temperature 210ᵒC, sudut pencetakan vertikal 90ᵒ. Sedangkan nilai kekuatan tarik terendah terdapat pada eksperimen nomor 43 dengan parameter infill Pattern Archimedean Chord, Nozzle Temperature 220ᵒC, sudut pencetakan vertikal 90ᵒ, dengan nilai kekuatan tarik sebesar 15,7 MPa. Sehingga dapat disimpulkan parameter proses tersebut mempengaruhi hasil dari pencetakan produk 3D printing.

Shaped Glued Connection of Two Parts Made by Rapid Prototyping Technology

2014 ◽  
Vol 555 ◽  
pp. 541-548 ◽  
Author(s):  
Jan Lipina ◽  
Václav Krys ◽  
Josef Sedlák
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Load Capacity ◽  
Great Emphasis ◽  
3D Printer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Construction Design

An increasing number of designs and subsequent production of parts created by the Rapid prototyping (RP) [1] technology led to a problem with the maximum workspace of the 3D printer. Due to this reason, it was necessary to work on the solution of joining the parts to overcome the limited workspace of the printer. This article is devoted to glue joints analysis of two parts made by RP technology. A great emphasis is given to the load capacity testing of the parts made this way. The measured values than may serve as a lead for the construction design of the outlined joints. The article builds on the knowledge gained during the previous testing of the screw connections of parts made by 3D printing technology [2].

scholarly journals Desain dan Manufaktur Model Piston Jupiter MX 135 cc Dengan Menggunakan 3D Printer

2020 ◽  
Vol 1 (2) ◽  
pp. 73-80
Author(s):  
Wandro Siregar ◽  
Richard A.M. Napitupulu ◽  
Parulian Siagian
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Manufacturing Process ◽  
Three Dimensional ◽  
Product Development Process ◽  
3D Printer ◽  
Three Dimension ◽  
Dimensional Object ◽  
Material Temperature ◽  
Thickness Layer

A product that will be mass produced requires an initial prototype so that it can assess whether a product design meets the desired criteria and is ready to be mass produced. For the purposes of making the initial prototyping, one alternative is to use 3D printing. Prototyping is an early example of a concept as part of the product development process. Rapid Prototyping allows the visualization of a 3D (three-dimension) image into an original three-dimensional object that has a volume. In addition, rapid prototyping products can also be used to test certain parts. In the design process the 2017 Solidworks software and manufacturing process are used anet type 3D printer. In the manufacturing process many 3D Printer parameters must be regulated and very influential on the manufacturing results to be obtained, including the 3D printer parameter settings in the slicing process. This is a process that is very influential on the results, where the process of slicing the material temperature, printing speed, wall thickness, layer thickness and support must be set properly. In the future it is expected that research on 3D printing manufacturing results with the same printer parameters for the design results of some CAD software.

Research on Common Problems Based on a Desktop 3D Printer

2015 ◽  
Vol 757 ◽  
pp. 175-178
Author(s):  
Kuan Gao ◽  
Ye Tao ◽  
Kai Zhang ◽  
Lu Xiang Song
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Rapid Development ◽  
3D Printer ◽  
Powder Metal ◽  
3D Printing Technology ◽  
Advantages And Disadvantages ◽  
Model File ◽  
Common Problems ◽  
Adhesive Materials

3D printing, that is, a kind of rapid prototyping technology, it is a kind of based on the digital model file, using the powder metal or plastic adhesive materials, such as to construct the object by means of step by step a print technology. 3D printing technology rapid development in recent years, It has to develop in the direction of miniature and generalization slowly from large professional, desktop 3D printing equipment is the representative products in this process. Based on the principle and characteristics of 3D printing, use the desktop 3D printer, the causes of some common problems in the process of printing and solvents are discussed. Based on these problems, the advantages and disadvantages of 3D printing are analyzed, and vision of the future are put forward.

Results of studying the dimensional accuracy of the bases of complete removable prostheses made using 3D printing and traditional technologies

2020 ◽  
pp. 34-39
Author(s):  
Vokulova Yu.A. Vokulova ◽  
E.N. Zhulev
Keyword(s):  
3D Printing ◽  
Traditional Method ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Digital Technologies ◽  
Dimensional Accuracy ◽  
3D Printer ◽  
Significance Level ◽  
Average Value ◽  
The Difference

This article presents the results of studying the dimensional accuracy of the bases of complete removable prostheses made using a 3D printer and the traditional method. Bases of complete removable prostheses were made using an intraoral laser scanner iTero Cadent (USA) and a 3D printer Asiga Max UV (Australia). To study the dimensional accuracy of the bases of complete removable prostheses, we used the DentalCAD 2.2 Valletta software. The Nonparametric Wilcoxon W-test was used for statistical analysis of the obtained data. We found that the average value of the difference with the standard for bases made using digital technologies is 0.08744±0.0484 mm. The average value of the difference with the standard for bases made by the traditional method is 0.5654±0.1611 mm. Based on these data, we concluded that the bases of complete removable prostheses made using modern digital technologies (intraoral laser scanning and 3D printer) have a higher dimensional accuracy compared to the bases of complete removable prostheses made using the traditional method with a significance level of p<0.05 (Wilcoxon's W-test=0, p=0.031). Keywords: digital technologies in dentistry, digital impressions, intraoral scanner, 3D printing, ExoCAD, complete removable dentures.

scholarly journals Efficient 3D printing via photooxidation of ketocoumarin based photopolymerization

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Xiaoyu Zhao ◽  
Ye Zhao ◽  
Ming-De Li ◽  
Zhong’an Li ◽  
Haiyan Peng ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Visible Light ◽  
Light Exposure ◽  
Three Dimensional ◽  
3D Printer ◽  
Light Penetration ◽  
Viable Solution

AbstractPhotopolymerization-based three-dimensional (3D) printing can enable customized manufacturing that is difficult to achieve through other traditional means. Nevertheless, it remains challenging to achieve efficient 3D printing due to the compromise between print speed and resolution. Herein, we report an efficient 3D printing approach based on the photooxidation of ketocoumarin that functions as the photosensitizer during photopolymerization, which can simultaneously deliver high print speed (5.1 cm h−1) and high print resolution (23 μm) on a common 3D printer. Mechanistically, the initiating radical and deethylated ketocoumarin are both generated upon visible light exposure, with the former giving rise to rapid photopolymerization and high print speed while the latter ensuring high print resolution by confining the light penetration. By comparison, the printed feature is hard to identify when the ketocoumarin encounters photoreduction due to the increased lateral photopolymerization. The proposed approach here provides a viable solution towards efficient additive manufacturing by controlling the photoreaction of photosensitizers during photopolymerization.

scholarly journals Mechanical properties of structures produced by 3D printing from composite materials

2019 ◽  
Vol 254 ◽  
pp. 01018
Author(s):  
František Bárnik ◽  
Milan Vaško ◽  
Milan Sága ◽  
Marián Handrik ◽  
Alžbeta Sapietová
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Carbon Fibers ◽  
3D Printer

By 3D printing it is possible to create different structures with different fiber-laying directions. These structures can be created depending on the type of 3D printer and its software. The Mark Two printer allows printing Onyx, a material based on nylon in combination with microcarbon fibers. Onyx can be used alone or reinforced with kevlar, glass or carbon fibers. This article deals with 3D printing and evaluation of mechanical properties of printed samples.

Sign in / Sign up

Export Citation Format

Share Document