scholarly journals Electrical conductivity of poly (L lactic acid) and poly (3-hydroxybutyrate) composites filled with galvanostatically produced copper powder

2018 ◽  
Vol 72 (5) ◽  
pp. 285-292
Author(s):  
Zoran Jankovic ◽  
Miroslav Pavlovic ◽  
Marijana Pantovic-Pavlovic ◽  
Nebojsa Nikolic ◽  
Vladan Zecevic ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Lactic Acid ◽  
Copper Powder ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Dendritic Structure ◽  
Electrolytic Copper Powder ◽  
Particle Size And Morphology ◽  
Percolation Thresholds ◽  
Size And Morphology

This manuscript presents experimental studies of composite materials based on poly (L lactic acid) (PLLA) and poly (3-hydroxybutyrate) (PHB) matrices filled with electrolytic copper powder, having a very high dendritic structure. Volume fractions of the copper powder used as filler in all prepared composites were varied in the range 0.5-6.0 vol.%. Samples were prepared by hot moulding injection at 170 ?C. Influence of particle size and morphology, as well as the influence of matrix type on conductivity and percolation threshold of the obtained composites were examined. Characterization included: electrical conductivity measurements using AC impedance spectroscopy (IS), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Fourier-transform Infrared spectroscopy (FTIR). Presence of three-dimensional conductive pathways was confirmed. The obtained percolation thresholds of 2.83 vol.% for PLLA and 3.13 vol.% for PHB composites were measured, which is about three times lower than the ones stated in the literature for similar composites. This property is ascribed to different morphologies of the filler used in the present investigation.

Electrical and Flexural Properties of Copper and Graphite Filled Phenolic Resin Composites

2011 ◽  
Vol 418-420 ◽  
pp. 1044-1047
Author(s):  
Mi Dan Li ◽  
Huan Niu ◽  
Shou Bin Wei ◽  
Hong Yang
Keyword(s):  
Electrical Conductivity ◽  
Flexural Strength ◽  
Copper Powder ◽  
Phenolic Resin ◽  
Dendritic Structure ◽  
Principal Factor ◽  
Resin Composites ◽  
Mechanical Mixing ◽  
Copper Particles ◽  
Copper Powders

Composites made of phenolic resin filled with graphite platelets and copper particles (copper powder, copper fiber or both mixture), are fabricated by mechanical mixing. The electrical conductivity of composite composed of 30 wt% resin, 50 wt% graphite and 20 wt% copper powder is up to 600S/cm. The efficiency of copper powder is compared with copper fiber. The results show that copper powder is more effective than copper fiber in improving electrical conductivity. The particle shape is also a principal factor in influencing flexural strength. In this study, the flexural strength of composites tends to increase with decreasing the ratio of copper fiber/copper powder because the dendritic structure of copper powder enhances the probability of graphite platelets embedded in the dendritic arms, which in fact help to distribute the external load from matrix to copper powders.

Direct manipulation of particle size and morphology of ordered mesoporous silica by flow synthesis

RSC Advances ◽  
2015 ◽  
Vol 5 (18) ◽  
pp. 13331-13340 ◽  
Author(s):  
T. N. Ng ◽  
X. Q. Chen ◽  
K. L. Yeung
Keyword(s):  
Particle Size ◽  
Mesoporous Silica ◽  
Hollow Spheres ◽  
Ordered Mesoporous Silica ◽  
Direct Manipulation ◽  
Flow Synthesis ◽  
Precise Control ◽  
Ordered Mesoporous ◽  
Particle Size And Morphology ◽  
Size And Morphology

Flow-synthesis of mesoporous silica allows deliberate and precise control over the size and shapes and enables the preparation of complex microstructures (i.e., hollow spheres).

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Targeting hepatocyte growth factor in epithelial–stromal interactions in an in vitro experimental model of human periodontitis

Odontology ◽  
2021 ◽  
Author(s):  
Yoko Yamaguchi ◽  
Akira Saito ◽  
Masafumi Horie ◽  
Akira Aoki ◽  
Patrick Micke ◽  
...  
Keyword(s):  
Growth Factor ◽  
Hepatocyte Growth Factor ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Collagen Gel ◽  
Neutralizing Antibody ◽  
Chronic Inflammatory Disease ◽  
Collagen Degradation ◽  
Hepatocyte Growth

AbstractPeriodontitis is a chronic inflammatory disease leading to progressive connective tissue degradation and loss of the tooth-supporting bone. Clinical and experimental studies suggest that hepatocyte growth factor (HGF) is involved in the dysregulated fibroblast–epithelial cell interactions in periodontitis. The aim of this study was to explore effects of HGF to impact fibroblast-induced collagen degradation. A patient-derived experimental cell culture model of periodontitis was applied. Primary human epithelial cells and fibroblasts isolated from periodontitis-affected gingiva were co-cultured in a three-dimensional collagen gel. The effects of HGF neutralizing antibody on collagen gel degradation were tested and transcriptome analyses were performed. HGF neutralizing antibody attenuated collagen degradation and elicited expression changes of genes related to extracellular matrix (ECM) and cell adhesion, indicating that HGF signaling inhibition leads to extensive impact on cell–cell and cell–ECM interactions. Our study highlights a potential role of HGF in periodontitis. Antagonizing HGF signaling by a neutralizing antibody may represent a novel approach for periodontitis treatment.

Poly-(lactic acid) and fibrin bioactive cellularized scaffold for use in bone regenerative medicine: Proof of concept

2021 ◽  
pp. 088391152199640
Author(s):  
Renata Aquino de Carvalho ◽  
Valmir Vieira Rocha Júnior ◽  
Antonio José Felix Carvalho ◽  
Heloisa Sobreiro Selistre de Araújo ◽  
Mônica Rosas Costa Iemma ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Regenerative Medicine ◽  
Platelet Rich Plasma ◽  
Three Dimensional ◽  
Culture Conditions ◽  
Infrapatellar Fat Pad ◽  
Dimensional Structure ◽  
Poly Lactic Acid ◽  
Proof Of Concept ◽  
Critical Bone Defects

Bone regenerative medicine (BRM) aims to overcome the limitations of conventional treatments for critical bone defects by developing therapeutic strategies, based on temporary bioactive substitutes, capable of stimulating, sustaining, and guiding tissue regeneration. The aim of this study was to validate the “proof of concept” of a cellularized bioactive scaffold and establish its potential for use in BRM. For this purpose, three-dimensional scaffolds of poly-(lactic acid) (PLA), produced by the additive manufacturing technique, were incorporated into a human platelet-rich plasma (PRP-h) fibrin matrix containing human infrapatellar fat pad mesenchymal stem cells (hIFPMSC). The scaffolds (PLA/finbrin-bioactive) were kept under ideal culture conditions in a medium free from fetal bovine serum and analyzed at 5 and 10 days by Scanning Electron Microscopy (SEM), Fourrier Transform Infrared (FTIR), Circular Dichroism and fluorescence microscopy. The results demonstrated the feasibility of obtaining a rigid, cytocompatible, and cellularized three-dimensional structure. In addition, PRP platelets and leukocytes were able to provide a bioactive environment capable of maintaining the viability of hIFPMSC into scaffolds. The results validate the concept of a customizable, bioactive, cellularized, and non-immunogenic strategy for application in BRM.

Sign in / Sign up

Export Citation Format

Share Document