The selection of the tail lift parameters

2018 ◽  
Vol 19 (10) ◽  
pp. 74-78
Author(s):  
Karol Tyszkowski ◽  
Zbigniew Kneba
Keyword(s):  
Computer Simulation ◽  
Compressed Air ◽  
Brake System ◽  
The Times ◽  
Set Up ◽  
Selection Of

The article concerns the discussion of a pneumatic tail lift entirely powered by pneumatic devices powered with compressed air from the brake system of truck. The authors try to set up the drive parameters and the size of the engines. For this purpose, a computer simulation of the platform's motion was made on the basis of which the torques of pneumatic engines were determined and the times of falling and lifting.

scholarly journals Analysis of the possibility of limiting the settling of sewage sumps installed in roadways

2019 ◽  
Vol 20 (1-2) ◽  
pp. 156-160
Author(s):  
Jarosław Bednarz ◽  
Jan Targosz ◽  
Jacek Wiederek
Keyword(s):  
Computer Simulation ◽  
Compressed Air ◽  
Brake System ◽  
The Times ◽  
Set Up

The article concerns the discussion of a pneumatic tail lift entirely powered by pneumatic devices powered with compressed air from the brake system of truck. The authors try to set up the drive parameters and the size of the engines. For this purpose, a computer simulation of the platform's motion was made on the basis of which the torques of pneumatic engines were determined and the times of falling and lifting.

scholarly journals Survey of publications by Polish authors in the field of moving loads on engineering structures

2018 ◽  
Vol 19 (12) ◽  
pp. 667-674 ◽  
Author(s):  
Wacław Szcześniak ◽  
Magdalena Ataman
Keyword(s):  
Computer Simulation ◽  
Compressed Air ◽  
Brake System ◽  
Moving Loads ◽  
Engineering Structures ◽  
The Times ◽  
Set Up

The article concerns the discussion of a pneumatic tail lift entirely powered by pneumatic devices powered with compressed air from the brake system of truck. The authors try to set up the drive parameters and the size of the engines. For this purpose, a computer simulation of the platform's motion was made on the basis of which the torques of pneumatic engines were determined and the times of falling and lifting.

Platelet Anti-Aggregating Activity and Tolerance of Clopidogrel in Atherosclerotic Patients

1996 ◽  
Vol 76 (06) ◽  
pp. 0939-0943 ◽  
Author(s):  
B Boneu ◽  
G Destelle ◽  
Keyword(s):  
Platelet Aggregation ◽  
Large Scale ◽  
Bleeding Time ◽  
Antithrombotic Activity ◽  
Ambulatory Patients ◽  
Patients At Risk ◽  
Set Up ◽  
Ischemic Events ◽  
Large Scale Clinical Trial ◽  
Selection Of

SummaryThe anti-aggregating activity of five rising doses of clopidogrel has been compared to that of ticlopidine in atherosclerotic patients. The aim of this study was to determine the dose of clopidogrel which should be tested in a large scale clinical trial of secondary prevention of ischemic events in patients suffering from vascular manifestations of atherosclerosis [CAPRIE (Clopidogrel vs Aspirin in Patients at Risk of Ischemic Events) trial]. A multicenter study involving 9 haematological laboratories and 29 clinical centers was set up. One hundred and fifty ambulatory patients were randomized into one of the seven following groups: clopidogrel at doses of 10, 25, 50,75 or 100 mg OD, ticlopidine 250 mg BID or placebo. ADP and collagen-induced platelet aggregation tests were performed before starting treatment and after 7 and 28 days. Bleeding time was performed on days 0 and 28. Patients were seen on days 0, 7 and 28 to check the clinical and biological tolerability of the treatment. Clopidogrel exerted a dose-related inhibition of ADP-induced platelet aggregation and bleeding time prolongation. In the presence of ADP (5 \lM) this inhibition ranged between 29% and 44% in comparison to pretreatment values. The bleeding times were prolonged by 1.5 to 1.7 times. These effects were non significantly different from those produced by ticlopidine. The clinical tolerability was good or fair in 97.5% of the patients. No haematological adverse events were recorded. These results allowed the selection of 75 mg once a day to evaluate and compare the antithrombotic activity of clopidogrel to that of aspirin in the CAPRIE trial.

STUDY OF INACCURACY IN THE OPERATION OF THE MAIN CONTROLLER OF STB MACHINE

2019 ◽  
Keyword(s):  
Normal Distribution ◽  
Stable Process ◽  
Random Errors ◽  
Actual Length ◽  
Experimental Data Processing ◽  
Set Up ◽  
Main Regulator ◽  
Transmission Gear ◽  
Selection Of

At production of fabrics, including fabrics for agricultural purpose, an important role is played by the cor-rect adjustment of operation of machine main regulator. The quality of setup of machine main controller is determined by the proper selection of rotation angle of warp beam weaving per one filling thread. In the pro-cess of using the regulator as a result of mistakes in adjustment, wear of transmission gear and backlashes in connections of details there are random changes in threads length. The purpose of the article is the research of property of random errors of basis giving by STB machine regulator. Mistakes can be both negative, and positive. In case of emergence only negative or only positive mistakes operation of the machine becomes im-possible as there will be a consecutive accumulation of mistakes. As a result of experimental data processing for stable process of weaving and the invariable diameter of basis threads winding of threads it is revealed that the random error of giving is set up as linear function of the accidental length having normal distribution. Measurements of accidental deviations in giving of a basis by the main regulator allowed to construct a curve of normal distribution of its actual length for one pass of weft thread. The presented curve of distribution of random errors in giving of a basis is the displaced curve of normal distribution of the accidental sizes. Also we define the density of probability of normal distribution of basis giving errors connected with a margin er-ror operation of the main regulator knowing of which allows to plan ways of their decrease that is important for improvement of quality of the produced fabrics.

Computer Simulation of a Press Feed Mechanism and Experimental Confirmation

1994 ◽  
Vol 116 (1) ◽  
pp. 248-256 ◽  
Author(s):  
C. Chassapis ◽  
G. G. Lowen
Keyword(s):  
Computer Simulation ◽  
Data Acquisition System ◽  
Quantitative Agreement ◽  
Drive Shaft ◽  
Strain Gages ◽  
Motion Equations ◽  
Qualitative And Quantitative ◽  
Bending Strain ◽  
Out Of Plane ◽  
Set Up

An experimentally verified simulation of the elastic-dynamic behavior of a lever-type feed mechanism is presented. Based on a combination of experimental and analytical findings, simplified motion equations could be introduced. In the experimental set-up, the motion of the mechanism is monitored by three angular encoders, which are attached to the drive shaft, the rocker-link shaft, and the feed roller shaft, respectively. Their output, which is stored in a specially designed data acquisition system, allows the correlation of the instantaneous rotations of the feed roller and the rocker shafts to that of the drive shaft. Strain gages provide in and out-of-plane bending-strain histories of the bent coupler. Experiment and theory, for different loading conditions, are correlated by way of the coupler strain, the clutch windup angle and the total feed length. Good qualitative and quantitative agreement between computed and experimental results was found.

GIS Based Multi-Criteria decision support system and machine learning for Hospital Site Selection case study Oran - Algeria

2022 ◽  
Vol 14 (1) ◽  
pp. 0-0
Keyword(s):  
Site Selection ◽  
Decision Makers ◽  
Analysis Method ◽  
Automatic Learning ◽  
Hospital Site ◽  
Set Up ◽  
High Level ◽  
Selection Of ◽  
The Ideal

The selection of hospital sites is one of the most important choice a decision maker has to take so as to resist the pandemic. The decision may considerably affect the outbreak transmission in terms of efficiency , budget, etc. The main targeted objective of this study is to find the ideal location where to set up a hospital in the willaya of Oran Alg. For this reason, we have used a geographic information system coupled to the multi-criteria analysis method AHP in order to evaluate diverse criteria of physiological positioning , environmental and economical. Another objective of this study is to evaluate the advanced techniques of the automatic learning . the method of the random forest (RF) for the patterning of the hospital site selection in the willaya of Oran. The result of our study may be useful to decision makers to know the suitability of the sites as it provides a high level of confidence and consequently accelerate the power to control the COVID19 pandemic.

A Ballast System for Automated Deep-Sea Ascents

2016 ◽  
Author(s):  
Matthias Golz ◽  
Florin Boeck ◽  
Sebastian Ritz ◽  
Gerd Holbach
Keyword(s):  
Environmental Impact ◽  
Environmental Contamination ◽  
Pressure Vessel ◽  
Deep Sea ◽  
Underwater Vehicles ◽  
Compressed Air ◽  
Hydraulic Pump ◽  
Unmanned Underwater Vehicles ◽  
The Past ◽  
Set Up

The efforts to discover the world’s oceans — even in extremely deep-sea environments — have grown more and more in the past years. In this context, unmanned underwater vehicles play a central role. Underwater systems that are not tethered need to provide an apparatus to ensure a safe return to the surface. Therefore, positive buoyancy is required and can be achieved by either losing weight or expanding volume. A conservative method is the dropping of ballast weight. However, nowadays this method is not appropriate due to the environmental impact. This paper presents a ballast system for an automated ascent of a deep-sea seabed station in up to 6000 m depth. The ballast system uses a DC motor driven modified hydraulic pump and a compressed air auxiliary system inside a pressure vessel. With regard to the environmental contamination in case of a leakage, only water is used as ballast fluid. The modification of an ordinary oil-hydraulic radial piston pump and the set-up of the ballast system is introduced. Results from sea trials in the Atlantic Ocean are presented to verify the functionality of the ballast system.

A New Approach to Drug Discovery

2012 ◽  
Vol 17 (4) ◽  
pp. 542-549 ◽  
Author(s):  
Maria Cândida Monteiro ◽  
Mercedes de la Cruz ◽  
Juan Cantizani ◽  
Catalina Moreno ◽  
José R. Tormo ◽  
...  
Keyword(s):  
Drug Discovery ◽  
Antifungal Activity ◽  
High Throughput Screening ◽  
Low Cost ◽  
Pharmacological Action ◽  
Natural Extracts ◽  
Microbial Extracts ◽  
Set Up ◽  
Microtiter Assay ◽  
Selection Of

Natural products are an inexhaustible source for drug discovery. However, the validation and selection of primary screening assays are vital to guarantee a selection of extracts or molecules with relevant pharmacological action and worthy of following up. The assay must be rapid, simple, easy to implement, and produce quick results and preferably at a low cost. In this work, we developed and validated a colorimetric microtiter assay using the resazurin viability dye. The parameters of the resazurin method for high-throughput screening (HTS) using natural extracts against Aspergillus fumigatus were optimized and set up. The extracts plus RPMI-1640 modified medium containing the spores and 0.002% resazurin were added per well. The fluorescence was read after 24 to 30 h of incubation. The resazurin proved to be as suitable as Alamar Blue for determining the minimal inhibitory concentration of different antifungals against A. fumigatus and effective to analyze fungicidal and fungistatic compounds. An HTS of 12 000 microbial extracts was carried out against two A. fumigatus strains, and 2.7% of the extracts displayed antifungal activity. Our group has been the first to use this methodology for screening a collection of natural extracts to identify compounds with antifungal activity against the medically important human pathogen A. fumigatus.

Sign in / Sign up

Export Citation Format

Share Document