scholarly journals The influence of hydrogen addition for exhaust gas emission in SI gas engine

2019 ◽  
Vol 20 (1-2) ◽  
pp. 241-245
Author(s):  
Karol Grab-Rogaliński
Keyword(s):  
Internal Combustion Engines ◽  
Exhaust System ◽  
Internal Combustion ◽  
Primary Energy ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Chemical Methods ◽  
Exhaust Gas Emission ◽  
Additional Fuel

One of the major problems in internal combustion engines is emission of pollutants with exhaust gases. Those pollutants are not only harmful for environment but also for humans. To decrease emission of pollutants many mechanical and chemical methods are used in internal combustion engines especially in exhaust system such as TWC, DPF, SCR. Alternative way for decrease in exhaust gas pollutants is use of alternative fuel as a primary energy carrier or as an additional fuel for base hydrocarbon one. In this studies the hydrogen was used as a additional fuel to methane. Both fuels were delivered to intake manifold. The share of the fuel was 100/0 methane/hydrogen and 70/30 methane/hydrogen. The addition of hydrogen to base fuel shown decrease of exhaust pollutants from engine and increase in engine operating parameters.

Calculation of Exhaust Gas Heat Produce for Ron 95, Ron97 and Vpower Racing Base Fuels use in Internal Combustion Engines

2017 ◽  
Vol 9 (3) ◽  
Author(s):  
I.B. Lias ◽  
H.B. Sharudin ◽  
M.H.B. Ismail ◽  
A.M.I.B. Mamat
Keyword(s):  
Heat Transfer ◽  
Heat Loss ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Exhaust System ◽  
Internal Combustion ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Exhaust Temperature ◽  
Different Types

The purpose of this study is to identify and analyse the calculation of exhaust gas heat produce (EGHP) in internal combustion engine (ICE) based on three types of fuel used specifically Petrol Ron 95, Petrol Ron 97 and Vpower racing base. The experimental test rig has used 1.6 CamPro Proton engine with 1561cc capacity and dynamometer. The calculation has used the basic formula of heat transfer equation and heat loss through the exhaust that included the mass flow rate of exhaust gas, specific heat of exhaust gas and temperature gradient. The exhaust temperature of ICE is generally in range from 400C to 600C and exhaust gas heat transfer affects the emissions burn-up in the exhaust system. This contributes significantly to the engine requirement. The experimental data was statistically analysed to identify the unknown parameter. High correlation of data variables can be determined based on the heat loss produced or EGHP. This also has significance by using different types of fuel in ICE.

scholarly journals Exhaust Gas Temperature Measurements in Diagnostics of Turbocharged Marine Internal Combustion Engines Part I Standard Measurements

2015 ◽  
Vol 22 (1) ◽  
pp. 47-54 ◽  
Author(s):  
Zbigniew Korczewski
Keyword(s):  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Technical Condition ◽  
Temperature Measurements ◽  
Injection System ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Gas Temperature ◽  
Measuring Signal ◽  
Exhaust Gas Temperature

Abstract The article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard online measurements of the exhaust gas temperature. A proposal is made to extend the parametric methods of diagnosing workspaces in turbocharged marine engines by analysing time-histories of enthalpy changes of the exhaust gas flowing to the turbocompressor turbine. Such a time-history can be worked out based on dynamic measurements of the exhaust gas temperature, performed using a specially designed sheathed thermocouple. The first part of the article discusses possibilities to perform diagnostic inference about technical condition of a marine engine with pulse turbocharging system based on standard measurements of exhaust gas temperature in characteristic control cross-sections of its thermal and flow system. Selected metrological issues of online exhaust gas temperature measurements in those engines are discusses in detail, with special attention being focused on the observed disturbances and thermodynamic interpretation of the recorded measuring signal. Diagnostic informativeness of the exhaust gas temperature measurements performed in steady-state conditions of engine operation is analysed in the context of possible evaluations of technical condition of the engine workspaces, the injection system, and the fuel delivery process.

Calculation of Acoustic Efficiency of Exhaust Silencers for Automotive Internal Combustion Engines

2021 ◽  
pp. 41-47
Author(s):  
Vladimir Tupov ◽  
O. Matasova
Keyword(s):  
Acoustic Waves ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Control Point ◽  
Plane Waves ◽  
Exhaust System ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Exhaust Noise ◽  
Insertion Losses

Insertion losses as the main characteristic that mathematically describes the acoustic efficiency of a noise silencer has been considered. This characteristic shows the reduction of noise generated by its source, in particular by the internal combustion engine’s exhaust system, at the control point as a silencer use result. Has been presented a mathematical description of the insertion losses, and have been considered parameters necessary for calculating this characteristic. Has been demonstrated the analytical dependence of impedance for the sound emission by the exhaust system’s end hole from the coefficient of acoustic waves reflection by this hole. The performed analysis of the widely used formulas for calculating the coefficient of sound reflection by the end hole has showed their insufficient accuracy for project designs performing. Have been proposed calculation dependences providing high accuracy for calculations of the reflection coefficient modulus, and the attached length of the channel end hole without a flange in the entire range of the existence of plane waves in it. It has been shown that the end correction of this hole at ka = 0 is 0.6127, and not 0.6133, as it was mistakenly believed until now in world acoustics. Has been proposed a method for calculation the exhaust noise source internal impedance. This method more accurately, in comparison with the already known ones, describes the acoustic processes in the internal combustion engine’s exhaust manifold, thanks to increases the accuracy of calculation the silencer acoustic efficiency, that allows develop the silencer at the early stages of the design of an automotive internal combustion engine.

Intake Air Path Diagnostics for Internal Combustion Engines

2006 ◽  
Vol 129 (1) ◽  
pp. 32-40 ◽  
Author(s):  
Matthew A. Franchek ◽  
Patrick J. Buehler ◽  
Imad Makki
Keyword(s):  
Steady State ◽  
Internal Combustion Engines ◽  
Air Flow ◽  
Internal Combustion ◽  
Flow Sensor ◽  
Path Model ◽  
Intake Manifold ◽  
Fault Estimation ◽  
Combustion Engines ◽  
Sensor Measurement

Presented is the detection, isolation, and estimation of faults that occur in the intake air path of internal combustion engines during steady state operation. The proposed diagnostic approach is based on a static air path model, which is adapted online such that the model output matches the measured output during steady state conditions. The resulting changes in the model coefficients create a vector whose magnitude and direction are used for fault detection and isolation. Fault estimation is realized by analyzing the residual between the actual sensor measurement and the output of the original (i.e., healthy) model. To identify the structure of the steady state air path model a process called system probing is developed. The proposed diagnostics algorithm is experimentally validated on the intake air path of a Ford 4.6L V-8 engine. The specific faults to be identified include two of the most problematic faults that degrade the performance of transient fueling controllers: bias in the mass air flow sensor and a leak in the intake manifold. The selected model inputs include throttle position and engine speed, and the output is the mass air flow sensor measurement.

Sign in / Sign up

Export Citation Format

Share Document