scholarly journals Pengaruh penambahan aluminium oksida terhadap kekuatan tarik dan tekan basis gigi tiruan resin akrilik polimerisasi panasThe effect of addition of aluminium oxide on the tensile and compressive strength of a heat-polymerised acrylic resin denture base

2018 ◽  
Vol 30 (3) ◽  
pp. 189
Author(s):  
Actara Rahmadita ◽  
Dwi Tjahyaning Putranti
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Testing Machine ◽  
Base Material ◽  
Aluminium Oxide ◽  
Acrylic Resin ◽  
Strength Test ◽  
Denture Base ◽  
Universal Testing Machine ◽  
Universal Testing

Pendahuluan: Resin akrilik polimerisasi panas (RAPP) merupakan bahan basis gigi tiruan yang paling banyak digunakan, namun memiliki sifat kekuatan tarik dan tekan yang rendah, sehingga diperlukan modifikasi dengan penambahan bahan penguat pada RAPP berupa aluminium oksida (Al2O3) atau alumina. Tujuan penelitian untuk menganalisi pengaruh penambahan aluminium oksida pada bahan basis gigi tiruan RAPP terhadap kekuatan tarik dan tekan. Metode: Jenis penelitian eksperimental laboratoris. Sebanyak 25 sampel berbentuk flat dumbbell shaped berukuran 60x12x3,9 (mm) untuk uji kekuatan tarik dan 25 sampel  berbentuk balok dengan ukuran 10x10x4 (mm) untuk uji kekuatan tekan. Pencampuran bubuk resin-aluminium oksida konsentasi 0,5%, 1,5%, 2,5% dan 3,5% dengan cairan resin dilakukan secara manual. Sampel direndam dalam air dan dimasukkan ke dalam inkubator. Uji dilakukan menggunakan universal testing machine dengan beban 1000N dan kecepatan crosshead 1mm/menit. Data dianalisis dengan uji ANOVA satu arah dan uji LSD. Hasil: Nilai kekuatan tarik kelompok kontrol dan keempat kelompok perlakuan penambahan aluminium oksida 0,5%, 1,5%, 2,5 %, 3,5% berturut turut adalah 50,867 MPa, 47,895 MPa, 45,107 MPa, 42,476 MPa, dan 39,753 MPa; sedangkan nilai kekuatan tekan kelompok kontrol dan keempat kelompok perlakuan penambahan aluminium oksida 0,5%, 1,5%, 2,5%, 3,5% berturut turut adalah 88,267 MPa, 106,085 MPa, 122,283 MPa, 135,367 MPa, dan 156,571 MPa. Penambahan bubuk aluminium oksida pada RAPP dapat menurunkan kekuatan tarik dan meningkatkan kekuatan tekan secara signifikan (p=0,0001 (p<0,05)), seiring dengan meningkatnya jumlah konsentrasi aluminium oksida yang ditambahkan. Simpulan: Penambahan aluminium oksida pada bahan basis gigi tiruan resin akrilik polimerisasi panas berpengaruh terhadap kekuatan tarik dan tekan.Kata kunci: Resin akrilik polimerisasi panas, aluminium oksida, kekuatan tarik, kekuatan tekan. ABSTRACT            Introduction: Heat-polymerised acrylic resin (HPAR) is the most widely used denture base material but has a low tensile and compressive strength thus modification is needed by adding reinforcement in the form of aluminium oxide (Al2O3) or alumina. The research objective was to analyse the effect of adding aluminium oxide on the tensile and compressive strength of HPAR denture base material. Methods: An experimental laboratory research was conducted towards the total of 25 samples in the form of flat dumbbell shape sized 60 x 12 x 3.9 mm for the tensile strength test, and 25 samples in the form of blocks with the size of 10 x 10 x 4 mm for the compressive strength test. The mixture of powdered aluminium oxide resin with the concentrations of 0.5%, 1.5%, 2.5%, and 3.5% with a liquid resin was carried out manually. The sample was then immersed in the water and put in an incubator. The test was performed using a universal testing machine with 1000 N loads and 1 mm/minute crosshead speed. Data obtained were analysed using the one-way ANOVA and LSD test. Result: The tensile strength values of the control group and all four treatment groups added with 0.5%, 1.5%, 2.5%, and 3.5% aluminum oxide were 50.867 MPa, 47.895 MPa, 45.107 MPa, 42.4476 MPa and 39.753 MPa respectively, while the compressive strength values were 88.267 MPa, 106.085, 122.283 MPa, 135.367 MPa, and 156.571 MPa consecutively. Addition of aluminium oxide powder to the HPAR can significantly reduce the tensile and compressive strength (p = 0.0001 (p < 0.05)) along with increasing concentration. Conclusion: Addition of aluminium oxide towards the HPAR denture base affected its tensile and compressive strength.Keywords: Heat-polymerised acrylic resin, aluminium oxide, tensile strength, compressive strength.

scholarly journals The effect of polyamide microparticles addition on some mechanical prop-erties of light-cured acrylic resin

2019 ◽  
Vol 10 (2) ◽  
pp. 1464-1469
Author(s):  
Adnan R. Al Assal ◽  
Abdalbaset A Fatalla ◽  
Mohammed Moudhaffar ◽  
Ghasak H Jani
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Base Material ◽  
Acrylic Resin ◽  
Strength Test ◽  
Control Group ◽  
Denture Base ◽  
Mean Values ◽  
Transverse Strength ◽  
Transverse Tensile

The general upgrading of polymer denture base material and research continuously looking for ideal restorative dental material with better properties, adequate esthetic properties, less expensive and easier to handle material to develop photo polymerization dental materials. This study was conducted to evaluate the effect of addition polyamide on mechanical microparticle properties light cure denture base material. One hindered sixty specimens from light-cured acrylic resin (Aurora). The divided mainly into four groups according to test used (Transverse strength test, impact strength test, hardness test and tensile strength test) with 40 specimens for each group. The results show an increase in Transverse strength, impact strength, hardness and tensile strength in all experimental group when compared to control group the highest mean values for all tests included in the study appeared in group B 1% polyamide. The addition of polyamide microparticle improves transverse, tensile, impact strength and hardness properties of denture base material.

scholarly journals Comparison of Microleakage and Compressive Strength of Different Base Materials

2021 ◽  
Vol 48 (2) ◽  
pp. 168-175
Author(s):  
Eunyeong Jang ◽  
Jaesik Lee ◽  
Soonhyeun Nam ◽  
Taeyub Kwon ◽  
Hyunjung Kim
Keyword(s):  
Methylene Blue ◽  
Compressive Strength ◽  
Composite Resin ◽  
Testing Machine ◽  
Base Material ◽  
Methylene Blue Solution ◽  
Universal Testing Machine ◽  
Base Materials ◽  
Universal Testing ◽  
Blue Solution

This study compared the microleakages and compressive strengths of various base materials.<br/>To evaluate microleakages, 50 extracted permanent premolars were prepared. The teeth divided into 5 groups of 10 each according to the base materials. Cavities with a 5.0 mm width, 3.0 mm length, and 3.0 mm depth were formed on the buccal surfaces of the teeth. After filling the cavities with different base materials, a composite resin was used for final restoration. Each specimen was immersed in 2% methylene blue solution and then observed under a stereoscopic microscope (× 30). To evaluate the compressive strength, 5 cylindrical specimens were prepared for each base material. A universal testing machine was used to measure the compressive strength.<br/>The microleakage was highest in the Riva light cure<sup>TM</sup> group and lowest in the Biodentine<sup>TM</sup> and Well-Root<sup>TM</sup> PT groups. For the compressive strengths, in all groups, acceptable strength values for base materials were found. The highest compressive strength was observed in the Fuji II LC<sup>TM</sup> group and the lowest strength in the Well-Root<sup>TM</sup> PT group.

scholarly journals Retention of provisional crowns cemented with eight temporary cements: comparative study

2004 ◽  
Vol 12 (3) ◽  
pp. 209-212 ◽  
Author(s):  
Mariana Ribeiro de Moraes Rego ◽  
Luiz Carlos Santiago
Keyword(s):  
Tensile Strength ◽  
Comparative Study ◽  
Testing Machine ◽  
Strength Test ◽  
The Other ◽  
Universal Testing Machine ◽  
Tensile Strength Test ◽  
Universal Testing ◽  
Significant Difference ◽  
Crown Preparation

Many temporary cements are commercially available; therefore, it is necessary to indicate them for each clinical requirement with regard to the tensile strength of prosthetic retainers. Thus, the purpose of this study was to compare the retention of provisional crowns cemented with eight temporary cements, over full crown preparations with standardized mechanical principles as height, taper, and length. For that purpose, eighty human first premolars received full crown preparation with standardized height and taper. Provisional crowns were fabricated and luted with eight brands of temporary cements. Twenty four hours after cementation, the restorations were submitted to tensile strength test in a universal testing machine and the data submitted to ANOVA and Bonferroni tests. Mean tensile strength values ranged from 20.1N for Nogenol cement to 67.5N for Hydro C cement. Statistically significant difference (p<0.05) was found between Hydro C and the other groups, except for Temp Bond and Rely X Temp, which presented statistically significant difference when compared to Freegenol and Nogenol temporary cements. The crowns cemented with Hydro C cement were more retentive that than those cemented with the other cements, except for Rely X Temp and Temp Bond. The less retentive crowns were those cemented with Nogenol and Freegenol temporary cements.

scholarly journals Sifat Mekanik Gigi Tiruan Akrilik dengan Penguat Serat Gelas

2017 ◽  
Vol 4 (02) ◽  
pp. 183
Author(s):  
Zuriah Sitorus ◽  
Awan Maghfirah ◽  
Yoshephin Romania ◽  
Syahrul Humaidi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Glass Fibre ◽  
Testing Machine ◽  
Acrylic Resin ◽  
Optimum Composition ◽  
Good Adhesion ◽  
Universal Testing ◽  
Short Glass Fibre ◽  
Short Glass

<p>The research is aimed to investigate the possibility of acrylic-reinforced glass fibre as a denture. Short glass fibre was made by variation of 4mm, 6 mm and 8mm. The results showed a good adhesion between glass fibre and acrylic resin with an optimum composition of the denture (acrylic: oil : glass fibre = 10 gr : 4.5 mL : 0.13 gr) was achieved. The density test was conducted by using Archimedes’ method, whereas compressive strength and tensile strength by using Universal Testing Machine (UTM). The results showed that glass fibre can be used to enhance the mechanical properties of acrylic resin. The optimum composition was achieved when 6 mm fibre had been added-in with a density of 1.2256 gr/cm3. A compressive strength of 76.623 MPa and a tensile strength of 71.207 MPa were recorded, these values can be applied as a denture.</p>

scholarly journals Kekuatan ikat geser gigi artifisial akrilik dan porselen pada tiga macam basis gigi tiruan nilon termoplastikThe shear bond strength of acrylic and porcelain teeth in three types of thermoplastic nylon denture bases

2019 ◽  
Vol 31 (1) ◽  
Author(s):  
Miftahussakinah Rizani ◽  
Hubban Nasution
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Base Material ◽  
Central Incisor ◽  
Denture Base ◽  
Maxillary Central Incisor ◽  
Universal Testing Machine ◽  
Universal Testing ◽  
Artificial Teeth

Pendahuluan: Kekuatan ikat geser adalah kekuatan maksimum suatu material untuk menahan atau menerima gaya geser hingga lepas atau terjadinya fraktur. Ini merupakan salah satu hal yang penting dalam penggunaan gigi tiruan, terutama pada gigi tiruan sebagian lepasan dengan bahan basis nilon termoplastik. Kekurangan bahan basis ini adalah sering terlepasnya gigi artifisial dari basis gigi tiruannya. Tujuan penelitian ini adalah untuk mengetahui perbedaan kekuatan ikat geser antara gigi artifisial akrilik maupun porselen dengan bahan basis gigi tiruan nilon termoplastik Valplast™, TCS™ dan Biotone™.  Metode: Jenis penelitian ini adalah eksperimental laboratoris. Sampel yang digunakan pada penelitian ini terdiri dari 18 gigi artifisial insisivus sentralis rahang atas akrilik dan 18 gigi artifisial insisivus sentralis rahang atas porselen yang dibagi ke dalam 6 kelompok. Tiap sampel ditanamkan pada bahan basis gigi tiruan berbentuk silindris dengan diameter 18 mm dan tinggi 20 mm. Sampel di uji dengan menggunakan alat Universal Testing Machine. Data dianalisis dengan menggunakan uji ANOVA satu arah. Hasil: Terdapat perbedaan kekuatan ikat geser yang signifikan (p<0,05). Pada kedua gigi artifisial kelompok dengan basis Valplast™ memiliki nilai kekuatan ikat geser tertinggi, lalu diikuti dengan kelompok TCS™ dan Biotone™. Simpulan: Nilai kekuatan ikat geser berbeda pada gigi artifisial akrilik maupun porselen pada tiga macam basis gigi tiruan nilon termoplastik.Kata kunci: Kekuatan ikat geser, nilon termoplastik, gigi artifisial akrilik, gigi artifisial porselen. ABSTRACTIntroduction: Shear bond strength is the maximum strength of a material to hold or accept shear forces until detached or fractured. This strength is one of the essential things in the denture usage, especially in removable partial denture with nylon thermoplastic base material. The disadvantage of this material base is the frequent detachment of artificial teeth from the denture base. The purpose of this study was to determine the difference of the shear bond strength between acrylic and porcelain teeth with thermoplastic nylon denture base material of Valplast™, TCS™, and Biotone™. Methods: The type of research was an experimental laboratory. The sample used in this study consisted of 18 acrylic maxillary central incisor artificial teeth and 18 porcelain maxillary central incisor artificial teeth divided into 6 groups. Each sample was implanted in cylindrical denture base material with a diameter of 18 mm and a height of 20 mm. The sample was tested using a Universal Testing Machine. Data were analysed using a one-way ANOVA test. Result: There were significant differences in the shear bond strength (p < 0.05) in both artificial teeth, with the group of Valplast™ base had the highest shear bond strength value, followed by the TCS™ and Biotone™ groups. Conclusion: The shear bond strength values of acrylic and porcelain teeth in three types of thermoplastic nylon denture bases were significantly different.Keywords: Shear bond strength, thermoplastic nylon, acrylic teeth, porcelain teeth.

scholarly journals Komparasi Pengujian Mutu Beton dengan Menggunakan Metode SNI 03-4430-1997 dan SNI 1974-1990 dalam Kegiatan Pengabdian Masyarakat di Laboratorium Struktur dan Bahan Konstruksi Universitas Brawijaya

2018 ◽  
Vol 2 (1) ◽  
pp. 1
Author(s):  
Sugeng Hendik ◽  
Dhino Teguh
Keyword(s):  
Compressive Strength ◽  
Testing Machine ◽  
Strength Test ◽  
Sample Type ◽  
Destructive Test ◽  
Universal Testing Machine ◽  
Universal Testing ◽  
Compressive Strength Test ◽  
Non Destructive ◽  
Test Result

ABSTRAK Penelitian ini adalah penelitian eksperimental yang dilakukan di laboratorium, untuk mengetahui perbandingan pengukuran kekuatan beton pada kegiatan pengabdian masyarakat di Laboratorium Struktur dan Bahan Konstruksi Fakultas Teknik Universitas Brawijaya. Pengukuran kekuatan beton bisa menggunakan metode merusak dan tidak merusak. Tujuan dari penelitian ini untuk mendapatkan konstanta pengali nilai hasil pengujian Hammer Test, sehingga hasilnya bisa mendekati hasil pengujian dengan menggunakan Mesin Uji Tekan. Adapun variabel penelitian adalah jenis sampel dan metode pengujian. Jumlah sampel untuk setiap umur beton adalah 20 silinder dan 20 kubus, sehingga total adalah 40 buah sampel beton, setelah itu dilakukan pengujian kekuatan dengan menggunakan metode non destruktif dan dengan bahan yang sama dilakukan pengujian kuat tekan dengan metode destruktif. Hasil penelitian ini menunjukkan bahwa pengujian dengan menggunakan hammer test nilainya lebih rendah dibandingkan dengan pengujian dengan Compression Machine dan didapatkannya konstanta pengali sebesar 0,88. Sehingga dengan menggunakan nilai hasil pengujian dengan alat hammer test estimasi kekuatan beton bisa diukur terlebih dahulu tanpa menggunakan metode Destruktif Kata-kata kunci : pengujian merusak dan tidak merusak, mesin uji tekan, uji kekerasan ABSTRACT This research is experimental research conducted at laboratory, to find the comparison of strength measurement of concrete in Community Service Activities at Laboratory of Structures and Construction Materials can use the method of destructive and non-destructive. The main purpose of this research is to get the value of multiplier constant from the test result of Hammer Test, so the result can come near to the test result by using Compression Machine. The research variable are; sample type (cube of 15 x 15 and cylinder of 15 x 30), testing method (hammer test vs Universal testing machine). The number of concrete cylinder sample (Ø 15 cm x 30cm) for each concrete age is 20 of cylinder and 20 of cube, so the total is 40 pcs of concrete sample, after that, compressive strength test is performed by using method of non-destructive and by the same materials, compressive strength test is performed by using method of destructive. The result of this research is prove that value test by using Hammer Test is lower that using Compression Machine and the obtained of multiplier constant is 0.88. So by using value of test result with hammer test, estimation of concrete strength can be measured in advance without using method of destructive. Keywords : destructive test, non-destructive test, universal testing machine, hammer test

scholarly journals Enhancement of the Tensile and the Compression Properties for Heat- Cured Acrylic Resin Denture Base Materials

2018 ◽  
Vol 15 (4) ◽  
pp. 449-454
Author(s):  
Baghdad Science Journal
Keyword(s):  
Polymethyl Methacrylate ◽  
Compression Strength ◽  
Base Material ◽  
Acrylic Resin ◽  
Tensile Tests ◽  
Strength Test ◽  
Denture Base ◽  
Compression Properties ◽  
Base Materials ◽  
Styrene Butadiene

This work aims to investigate the tensile and compression strengths of heat- cured acrylic resin denture base material by adding styrene-butadiene (S- B) to polymethyl methacrylate (PMMA). The most well- known issue in prosthodontic practice is fracture of a denture base. All samples were a blend of (90%, 80%) PMMA and (10%, 20%) S- B powder melted in Oxolane (Tetra hydro furan). These samples were chopped down into specimens of dimensions 100x10x2.5mm to carry out the requirements of tensile tests. The compression strength test specimens were shaped into a cylinder with dimensions of 12.7mm in diameter and 20mm in length. The experimental results show a significant increase in both tensile and compression strengths when compared to control (standard) results for the preparation material.

scholarly journals Compressive strength of glass ionomer cements using different specimen dimensions

2007 ◽  
Vol 21 (3) ◽  
pp. 204-208 ◽  
Author(s):  
André Mallmann ◽  
Jane Clei Oliveira Ataíde ◽  
Rosa Amoedo ◽  
Paulo Vicente Rocha ◽  
Letícia Borges Jacques
Keyword(s):  
Compressive Strength ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
Strength Test ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Universal Testing ◽  
Resin Modified Glass Ionomer ◽  
Compressive Strength Test ◽  
Ionomer Cement

The purpose of this study was to evaluate the compressive strength of two glass ionomer cements, a conventional one (Vitro Fil® - DFL) and a resin-modified material (Vitro Fil LC® - DFL), using two test specimen dimensions: One with 6 mm in height and 4 mm in diameter and the other with 12 mm in height and 6 mm in diameter, according to the ISO 7489:1986 specification and the ANSI/ADA Specification No. 66 for Dental Glass Ionomer Cement, respectively. Ten specimens were fabricated with each material and for each size, in a total of 40 specimens. They were stored in distilled water for 24 hours and then subjected to a compressive strength test in a universal testing machine (EMIC), at a crosshead speed of 0.5 mm/min. The data were statistically analyzed using the Kruskal-Wallis test (5%). Mean compressive strength values (MPa) were: 54.00 ± 6.6 and 105.10 ± 17.3 for the 12 mm x 6 mm sample using Vitro Fil and Vitro Fil LC, respectively, and 46.00 ± 3.8 and 91.10 ± 8.2 for the 6 mm x 4 mm sample using Vitro Fil and Vitro Fil LC, respectively. The resin-modified glass ionomer cement obtained the best results, irrespective of specimen dimensions. For both glass ionomer materials, the 12 mm x 6 mm matrix led to higher compressive strength results than the 6 mm x 4 mm matrix. A higher variability in results was observed when the glass ionomer cements were used in the larger matrices.

scholarly journals Statistical Analysis of Tensile Strength and Flexural Strength Data from Universal Testing Machine

2020 ◽  
pp. 54-62
Author(s):  
Ahmad Adlie Shamsuri ◽  
Siti Atiqa Al Zahra Mat Darus
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Testing Machine ◽  
Z Score ◽  
P Values ◽  
Strength Data ◽  
Universal Testing Machine ◽  
Universal Testing ◽  
Relative Standard ◽  
The Difference

The tensile strength and flexural strength are the most important mechanical properties as they provide the value of maximum tensile stress and flexural stress. The objective of this study is to analyze statistically the tensile strength and flexural strength data obtained from a universal testing machine. The tests were conducted upon a thermoplastic, specifically high-density polyethylene (HDPE), which was in-house molded by using an injection-molding machine. Three different persons have performed the tensile and flexural tests. Three other laboratories have also been involved in these tests. The relative standard deviation (RSD) values were calculated to express the precision and repeatability of the tests. Later, the standard score (z-score) values were also calculated to aid the comparison of the data. Finally, the single-factor analysis of variance (ANOVA) was employed to investigate statistically significant differences between the means of the tensile strength and flexural strength data of each person and laboratory. From the calculation, the RSD values of all three persons and laboratories were lower than 5%, indicating that the data were consistent. The z-score values of all three persons were within the range from -2 to 2, suggesting that the data were close to average. However, the z-score value for one of three laboratories was not within the range, demonstrating that the data was unusual. The P-values of all three persons were higher than 0.05 (except for flexural strength), implying that the difference between the means of the data was not statistically significant. Nevertheless, the P-values of all three laboratories were lower than 0.05, indicating that the difference between the means of the data was statistically significant.

scholarly journals KARAKTERISASI UJI KEKUATAN TARIK (TENSILE STRENGHT) FILM PLASTIK BIODEGRADABLE DARI TANDAN KOSONG KELAPA SAWIT DENGAN PENGUAT ZINK OKSIDA DAN GLISEROL

2018 ◽  
Vol 5 (2) ◽  
Author(s):  
Agustina Mandasari ◽  
Mutya Fika Safitri ◽  
Essy Risa Perangin-angin ◽  
Dian Sunarwati ◽  
Wulan Dwi Safitri ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Testing Machine ◽  
Biodegradable Film ◽  
Universal Testing Machine ◽  
Universal Testing ◽  
Tensile Strenght

Telah dilakukan karakterisasi uji kekuatan tarik (tensile strength) film plastik biodegradable dari tandan kosong kelapa sawit dengan penguat zink oksida dan gliserol. Penelitian ini bertujuan untuk mengetahui kekuatan tarik film plastik biodegradable yang dihasilkan dari tandan kosong kelapa sawit dengan variasi ZnO dan gliserol (a) 0 %  ZnO dan 50% gliserol; (b) 2% ZnO dan 25% gliserol; (c) 9% ZnO dan 25% gliserol; (d) 3% ZnO dan 50 % gliserol. Metode penelitian yang digunakan adalah analisis sifat mekanik dan uji kekuatan tarik film plastik menggunakan Universal Testing Machine (UTM). Hasil penelitian menunjukan bahwa kuat tarik pada film plastik biodegradable dipengaruhi oleh konsentrasi gliserol dan ZnO. Kuat tarik maksimal yang didapat dari penelitian yaitu 12,642 MPa dengan komposisi gliserol 25% dan ZnO 9%. Hal ini menunjukkan bahwa semakin banyak penambahan komposisi gliserol dan ZnO maka kuat tarik plasik akan semakin baik. Kata kunci : biodegradable film, kuat tarik, tandan kosong kelapa sawit

Sign in / Sign up

Export Citation Format

Share Document