scholarly journals Bonding Performance for Lightweight Concrete: A Review

2020 ◽  
Vol 13 (4) ◽  
pp. 58-70
Author(s):  
Rafal Ahmed ◽  
Suhad M. Abed
Keyword(s):  
Experimental Work ◽  
Lightweight Concrete ◽  
Light Weight ◽  
Reinforcing Bars ◽  
Great Caution ◽  
Bond Behavior ◽  
Construction Companies ◽  
Bonding Performance ◽  
Concrete Type ◽  
Concrete Face

Nowadays, lightweight concrete become popular among construction companies due to its physical characteristic such as sound and thermal insulation, lightweight, cost and environmental saving, self-levelling…etc., which make it an attractive choice as a building material. However, this concrete face many constructional obstacles due to the lack of adequate and sufficient constructional information about the nature of this concrete. This requires great caution when use it for structural purposes. Among these great constraints, for example, is the weak characteristic of the bond between this concrete and reinforcing steel. Therefore, in order to get rid of these defects of concrete and make it usable in various construction sectors, this paper summarizes researchers works concerning bond behavior between light weight concrete and reinforcing bars , the variable influencing bond behavior such as; concrete type, rebar type and diameter, W/C ratio, and adding fibres. And results collected from experimental work with most important conclusions

Size Effect on the Bond Behavior of Grouted Reinforcing Bars Embedded in Light-weight Concrete

2021 ◽  
Author(s):  
Aamer Abbas ◽  
◽  
Yaqoob Yaqoob ◽  
Ola Hussein ◽  
Ibrahim Al-Ani ◽  
...  
Keyword(s):  
Bond Strength ◽  
Concrete Specimen ◽  
Light Weight ◽  
Reinforcing Bars ◽  
Conventional Concrete ◽  
Bond Behavior ◽  
Pull Out ◽  
Specimen Width ◽  
Light Weight Concrete ◽  
The Relationship

This study presents experimentally the bond behavior of light-weight concrete specimens with grouted reinforcing bars in comparison with conventional concrete specimens. A total of (9) pull-out specimens were studied; (3) specimens of conventional concrete, (3) specimens of light-weight concrete, and other (3) specimens of grouted light-weight concrete. Two variables are adopted in this investigation: specimen width and type of concrete (conventional concrete, light-weight concrete and grouted light-weight concrete). The study contains a discussion of the general behavior of the specimens in addition to the study of the ultimate bond capacity, maximum bond stresses and the relationship between the stress and the slip for different pull-out specimens. Results show that bond strength is highest for the largest specimen size (bond strength of grouted light-weight concrete specimen with specimen width 400 mm is higher than that of the specimen with (200 mm) width by about (13.13%)). Also, bond strength is highest for the grouted light-weight concrete specimen (bond strength of grouted light-weight concrete specimen is higher than conventional concrete specimen by (11.11%)).

scholarly journals EXAMINATION OF FROST DAMAGE RESISTANCE FOR FREEZE-THAW OF LIGHTWEIGHT CONCRETE TYPE 2

2014 ◽  
Vol 20 (46) ◽  
pp. 851-854
Author(s):  
Toshiyuki UEMATSU ◽  
Yasumichi KOSHIRO ◽  
Kenichi ICHISE
Keyword(s):  
Lightweight Concrete ◽  
Frost Damage ◽  
Damage Resistance ◽  
Freeze Thaw ◽  
Concrete Type

Development of Lightweight Concrete using Industrial Waste Palm Oil Clinker

2021 ◽  
Author(s):  
Ibrahim Al-Ani ◽  
◽  
Wan Hamidon ◽  
Wan Mohtar ◽  
Basma Alwachy ◽  
...  
Keyword(s):  
Palm Oil ◽  
Oil Palm ◽  
Lightweight Concrete ◽  
Light Weight ◽  
Durability Properties ◽  
Light Weight Concrete ◽  
Water Absorption Test ◽  
Natural Aggregates ◽  
Definition Of ◽  
Strength And Durability

Concrete is a major material used in the construction of buildings and structures in the world. Gravel and sand are the major ingredients of concrete but are non-renewable natural materials. Therefore, the utilisation of palm oil clinker (POC), a solid waste generated from palm oil industry is proposed to replace natural aggregate in this research to reduce the demand for natural aggregates. One mix of ordinary concrete as control concrete; while four mix proportions of oil palm clinker concrete were obtained by replacing 25 %, 50 %, 75 %, and 100 % of gravel and sand of control concrete with coarse and fine oil palm clinker respectively by volume, with same cement content and water cement ratio. Compressive strength test was carried out of concretes with different percentages of oil palm clinker; whereas water absorption test according to respective standard, were carried out to determine the durability properties of various mixes. Based on the results obtained, the study on the effect of percentage of clinker on strength and durability properties was drawn. According to ACI classification of light weight concrete only the 100 percentage replacement can achieve the definition of light weight concrete since its density less than 1900 kg/m3 and strength larger than 17 MPa. Eventually the 25 % replacement of the normal aggregate by the OPC will improve the strength and durability of the concrete.

scholarly journals Structural Use of Expanded Polystyrene Concrete

2020 ◽  
Vol 5 (6) ◽  
pp. 1131-1138
Author(s):  
Adeniran Jolaade ADEALA ◽  
Olugbenga Babajide SOYEM
Keyword(s):  
Environmental Pollution ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Consumer Products ◽  
Expanded Polystyrene ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Construction Companies ◽  
Fine Aggregates ◽  
Concrete Matrix

Expanded polystyrene (EPS) wastes are generated from industries and post-consumer products. They are non-biodegradable but are usually disposed by burning or landfilling leading to environmental pollution. The possibility of using EPS as partial replacement for fine aggregates in concrete has generated research interests in recent times. However, since the physical and mechanical properties of EPS are not like those of conventional fine aggregates, this study is focussed on the use of EPS as an additive in concrete while keeping other composition (sand and granite) constant. Expanded polystyrene was milled, the bulk density of EPS was 10.57kg/m3 and particle size distributions were determined. Engineering properties of expanded polystyrene concrete were determined in accordance with BS 8110-2:1985. The result showed that the amount of expanded polystyrene incorporated in concrete influence the properties of hardened and fresh concrete. The compressive strengths of 17.07MPa with 5 % expanded polystyrene concrete at 28 days for example can be used as a lightweight concrete for partitioning in offices. Incorporating expanded polystyrene granules in a concrete matrix can produce lightweight polystyrene aggregate concrete of various densities, compressive strengths, flexural strengths and tensile strengths. In conclusion, this reduces environmental pollution, reduction in valuable landfill space and also for sustainability in construction companies

Sustainable construction

2020 ◽  
Vol 20 (2) ◽  
pp. 191-207 ◽  
Author(s):  
Muhammad Waseem Khan ◽  
Yousaf Ali
Keyword(s):  
Life Cycle ◽  
Rice Husk ◽  
Life Cycle Cost ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Content Type ◽  
Government Organizations ◽  
Construction Companies ◽  
Concrete Type ◽  
The Impact

Purpose The change in climate and depletion of natural resources because of the harmful emissions from different materials becomes a main issue for the globe. Some of the developed and developing countries have focused on this issue and performed research to provide a solution. The purpose of this study is to identify the best types of concrete based on its impact on the environment and economy. Design/methodology/approach The life cycle assessment and life cycle cost analysis of six concrete mixtures that include construction and demolition wastes (CDW), marble sludge, rice husk and bagasse ash as a partial replacement of cement, are performed. These types of concrete are compared with each other and with ordinary concrete to select the best possible concrete type for a developing country, like Pakistan. Findings The results show that, although for an agricultural country like Pakistan, the agriculture wastes such as rice husk and bagasse ash are preferable to be used, if the emissions of CO2 and CO from rice husk and NOx and SO2 from bagasse ash are properly controlled. However, based on the results, it is recommended to use the CDW in concrete because of the small amount of air emissions and affordable prices. Originality/value Through this study, a path has been provided to construction companies and relative government organizations of Pakistan, which leads to sustainable practices in the construction industry. Moreover, the base is provided for future researchers who want to work in this area, as for Pakistan, there is no database available that helps to identify the impact of different concrete on the environment.

Utilization of Non-Traditional Fibers for Light Weight Concrete Production

2018 ◽  
Vol 760 ◽  
pp. 231-236
Author(s):  
Jiri Zach ◽  
Martin Sedlmajer ◽  
Jan Bubenik ◽  
Vitezslav Novak
Keyword(s):  
Thermal Insulation ◽  
Energy Savings ◽  
Lightweight Concrete ◽  
Foam Glass ◽  
Construction Materials ◽  
Light Weight ◽  
Heating And Cooling ◽  
Concrete Production ◽  
Flat Roofs ◽  
Rapid Drop

Along with energy savings for heating and cooling, the demand for thermal insulation materials is increasing and is an attempt to achieve good thermal insulation properties for some of the construction materials. In the field of porous and lightweight concrete, this is e.g. concrete for foundations, concrete for floor constructions or flat roofs. The problem with these concrete is a relatively rapid drop in mechanical properties in reducing bulk density, with using conventional silicate binders, especially in the area below 1000 kg/m3. The paper describes the possibility of using recycled organic fibers in combination with lightweight aggregates based on foam glass for the production of porous and lightweight concrete with a good ratio of mechanical and thermal insulation properties.

scholarly journals Experience of using high-rigidity bearing reinforcement in monolithic lightweight concrete slabs

2019 ◽  
Vol 265 ◽  
pp. 05031
Author(s):  
Artem Davidyuk ◽  
Tejmuraz Guladze ◽  
Yuliya Kustikova ◽  
Timofey Laryushkin
Keyword(s):  
Lightweight Concrete ◽  
Concrete Slabs ◽  
Reinforcing Bars ◽  
High Rigidity

The article describes the experience of erecting lightweight concrete monolithic slabs with the use of reinforcing bars of increased rigidity. As a result, a reduction in costs of 25 ... 30%, compared with the floors of heavy concrete without pre-stressed reinforcement is reached.

Influence of the Steel Fiber Length on the Properties of Lightweight Concrete

2013 ◽  
Vol 739 ◽  
pp. 251-254
Author(s):  
Ru Jie Huang ◽  
Chen Shi ◽  
Guo Xin Li
Keyword(s):  
Tensile Strength ◽  
Fiber Length ◽  
Elasticity Modulus ◽  
Steel Fiber ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Earthquake Resistance ◽  
Lightweight Aggregate Concrete ◽  
Light Weight ◽  
Aggregate Concrete

Lightweight aggregate concrete has lower density and lower elasticity modulus, so it has better earthquake resistance. But the low strength limited the application of lightweight concrete. Steel fiber can improve the strength of lightweight aggregate concrete. In this paper, the influences of different lengths of steel fiber on the slump, compressive strength, splitting tensile strength and antiflex cracking strength are investigated. The results show that adding steel fiber reduces the workability of the concrete mixture, but it improved the each strength of light weight concrete and different lengths have the different regularity of effects.

Sign in / Sign up

Export Citation Format

Share Document