On the Performance of Boundary Layer Suction for Secondary Flow Control in a High Speed Compressor Cascade

2013 ◽  
Author(s):  
Karsten Liesner ◽  
Robert Meyer ◽  
Christoph Gmelin ◽  
Frank Thiele
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Secondary Flow ◽  
High Speed ◽  
Compressor Cascade ◽  
Boundary Layer Suction

Endwall Secondary Flow Control in a High Speed Compressor Cascade With Vortex Generator Jets

2016 ◽  
Author(s):  
Huaping Liu ◽  
Deying Li ◽  
Bingxiao Lu ◽  
Menghan Yu
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Secondary Flow ◽  
High Speed ◽  
Vortex Generator ◽  
Low Energy ◽  
Incoming Flow ◽  
Compressor Cascade ◽  
Flow Angle ◽  
Vortex Generator Jets

This paper presents a numerical investigation of secondary flow control in a high speed compressor cascade for different incoming flow incidences by means of endwall vortex generator jets (VGJs). The inlet Reynolds number is 560,000 in corresponding to an inlet Mach number of 0.67. Based on the detail analysis of the flow field and cascade performance, two effect mechanisms of the vortex induced by the VGJ are proposed. The first is to enhance the mixing between the endwall boundary layer and the mainstream. The second is to block the cross flow as an air obstacle. Therefore, the low energy fluids accumulation in the corner region could be decreased significantly, weakening the separation on the suction side and reducing the losses effectively. This benefit becomes more obvious with the increase of the incidence from i = −2° to 4°. Additionally, a more uniform flow angle as well as static pressure profile along the blade height is obtained at the cascade outlet. The maximum loss reduction is up to 12.9% while i = 4° with a jet mass flow ratio of 0.2%. However, the unfavorable impact of the VGJs is also detected in the up-washed region, where the loss is increased by the mixing processes between the mainstream fluids and the low energy fluids. For the case i = −4°, a strengthened induced vortex is generated due to the increased angle between the jet and incoming flow, resulting in loss increase in the up-washed region. Besides, a more rapid corner boundary layer development appears in the rear part of the passage, contributing to severe separation and loss enhancement, which suggests that the VGJ should be switched off for this incidence. Therefore, the advice to the application of the VGJ according the incidence is further obtained.

Combination of Active and Passive Flow Control in a High Speed Compressor Cascade

2014 ◽  
Author(s):  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
High Speed ◽  
Active Flow Control ◽  
Side Wall ◽  
Suction Side ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Compressor Cascade ◽  
Boundary Layer Suction

An experimental study is presented in which passive and active flow control are combined in a way that they complement and support one other. Secondary flow control using boundary layer fences is combined with a boundary layer suction in a compressor cascade at high Mach numbers. Inflow Mach number of 0.67 and Reynolds number (based on chord length) of 560.000 assure realistic conditions. The cascade, equipped with five stator vanes of NACA65 K48 type is used in an ambient condition measurement environment. Pressure measurements form the basis of the experimental investigations, flow visualization is used to obtain insight into the topology of the flow field. The boundary layer fences installed on the suction side of the vanes create a region of low-loss two dimensional flow in the center of the passage. A region of high flow loss is generated at the side wall between wall and BL fence. This region is treated with through-wall boundary layer suction as used in previous investigations. This helps stabilize the flow near the wall and prevent large separated areas. The total pressure loss is reduced remarkably and the outflow becomes more two-dimensional compared to the reference measurement and even compared to the measurement with suction applied without BL fences. The application of boundary layer fences on flow-suction experiments allows obtaining the same loss reduction gains by using lower amounts of suction.

Boundary layer suction for high-speed air intakes: A review

2018 ◽  
Vol 233 (9) ◽  
pp. 3459-3481 ◽  
Author(s):  
Javad Sepahi-Younsi ◽  
Behzad Forouzi Feshalami ◽  
Seyed Reza Maadi ◽  
Mohammad Reza Soltani
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Flow Control ◽  
High Speed ◽  
Control Methods ◽  
Slant Angle ◽  
Boundary Layer Suction ◽  
Recent Developments

The paper summarizes recent developments in boundary layer suction for high-speed air intakes. Bleed has been efficiently used in supersonic and hypersonic intakes for three primary reasons: to improve the performance of the intake, to reduce the starting Mach number of the intake, and to postpone the onset of buzz oscillations. A bleed system has many characteristics such as the bleed entrance and exit areas, bleed entrance slant angle and position, and bleed type (slot or porous and ram-scoop or flush). Each of these parameters has significant impacts on the intake performance and stability that have been reviewed in this study. In addition, the effectiveness of other flow control methods has been compared with the bleed method.

Secondary flow control using endwall jet fence in a high-speed compressor cascade

2017 ◽  
Vol 31 (10) ◽  
pp. 4841-4852 ◽  
Author(s):  
Huaping Liu ◽  
Shuai Jiang ◽  
Yongchuan Yu ◽  
Dongfei Zhang ◽  
Huanlong Chen
Keyword(s):  
Flow Control ◽  
Secondary Flow ◽  
High Speed ◽  
Compressor Cascade

The Cost of Flow Control in a Compressor

2011 ◽  
Author(s):  
Simon W. Evans ◽  
Howard P. Hodson
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Vortex Generator ◽  
Control Methods ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Boundary Layer Suction ◽  
Blade Row ◽  
Efficiency Increase ◽  
The Cost

This paper documents an analysis performed to estimate the cycle cost of flow control in a compressor. The analysis is based on a series of experiments conducted in a low-speed compressor cascade at high incidence. In these experiments, flow control was applied to delay a turbulent separation on the suction surfaces of the blades in the cascade. The flow control methods studied include boundary layer suction and both steady and pulsed vortex generator jets. Endwall control was also applied to remove corner separations. Tip gaps and endwall suction were both studied for this purpose. The flow control methods studied were able to successfully delay a separation occurring on the suction surface of the blades, reducing the loss coefficient. The mass flow rates and jet supply pressures required to achieve control in each case were used to model a single flow-controlled blade row in a typical turbofan cycle using cycle analysis software. The cost of control to the cycle was calculated as the polytropic compressor efficiency increase required to maintain thrust relative to a conventional cycle with no flow control. The results of the analysis show that the benefits of flow control significantly outweigh the cost. They also show that boundary layer suction coupled with endwall suction yields the lowest cycle cost. This is because of the small pressure difference required to drive suction, which allows reinjection of the aspirated air a short distance upstream of the flow controlled blade row.

Effect of Segment Endwall Boundary Layer Suction on Compressor 3D Corner Separation

2015 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
High Speed ◽  
Flow Behavior ◽  
Pressure Ratio ◽  
Base Flow ◽  
Flow Ratio ◽  
Compressor Cascade ◽  
Corner Separation ◽  
Boundary Layer Suction ◽  
Suction Flow

Due to the strong secondary flow behavior in the compressor endwall/blade suction-side corner region, a large three-dimensional corner separation will usually be formed with large amounts of compressor aerodynamic loss. In this paper, a linear high-speed compressor cascade, with five NACA 65-K48 stator profiles, is numerically simulated to understand the state of this phenomenon. Based on the experiment, the base flow is validated for the numerical result. Active control of 3D corner separation was investigated by using segment endwall boundary layer suction, which is located along the pressure-side leg of leading-edge horse-shoe vortex during its development in the frontal part of the blade passage. The influence of suction flow ratio was investigated in an effort to quantify the improvements of compressor cascade performance. The results show the optimal suction flow ratio is not the largest, but a critical value, which is 0.83% of inflow mass flow rate. Taking all performance parameters’ changes into consideration, the best is with 1% suction flow ratio. The total-pressure loss is eventually reduced by 11.2% with the optimal suction flow ratio compared to the design condition, and an increase of 9.84% is obtained for the static-pressure ratio.

Effect of Boundary Layer Suction on Aerodynamic Performance of High-Turning Compressor Cascade

2013 ◽  
Author(s):  
Longxin Zhang ◽  
Shaowen Chen ◽  
Hao Xu ◽  
Jun Ding ◽  
Songtao Wang
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Experimental Studies ◽  
Aerodynamic Performance ◽  
Parameter Distribution ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
End Wall ◽  
Low Speed Wind Tunnel ◽  
Good Agreement

Compared with suction slots, suction holes are (1) flexible in distribution; (2) alterable in size; (3) easy to fabricate and (4) high in strength. In this paper, the numerical and experimental studies for a high turning compressor cascade with suction air removed by using suction holes in the end-wall at a low Mach numbers are carried out. The main objective of the investigation is to study the influence of different suction distributions on the aerodynamic performance of the compressor cascade and to find a better compound suction scheme. A numerical model was first made and validated by comparing with the experimental results. The computed flow visualization and exit parameter distribution showed a good agreement with experimental data. Second, the model was then used to simulate the influence of different suction distributions on the aerodynamic performance of the compressor cascade. A better compound suction scheme was obtained by summarizing numerical results and tested in a low speed wind tunnel. As a result, the compound suction scheme can be used to significantly improve the performance of the compressor cascade because the corner separation gets further suppressed.

Sign in / Sign up

Export Citation Format

Share Document