EFFECT OF PROCESS PARAMETERS ON SURFACE FINISH IN SINGLE POINT INCREMENTAL FORMING PROCESS - A REVIEW

2019 ◽  
Vol 9 (1) ◽  
pp. 44
Author(s):  
KUMAR NARINDER ◽  
R. M. BELOKAR ◽  
◽  
Keyword(s):  
Process Parameters ◽  
Surface Finish ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process

scholarly journals A Novel Machine-Learning-Based Procedure to Determine the Surface Finish Quality of Titanium Alloy Parts Obtained by Heat Assisted Single Point Incremental Forming

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1287
Author(s):  
Fernando Bautista-Monsalve ◽  
Francisco García-Sevilla ◽  
Valentín Miguel ◽  
Jesús Naranjo ◽  
María Carmen Manjabacas
Keyword(s):  
Machine Learning ◽  
Surface Finish ◽  
Incremental Forming ◽  
Single Point ◽  
Polynomial Kernel ◽  
Support Vector ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Metal Forming Process ◽  
And Performance

Single point incremental forming (SPIF) is a cheap and flexible sheet metal forming process for rapid manufacturing of complex geometries. Additionally, it is important for engineers to measure the surface finish of work pieces to assess their quality and performance. In this paper, a predictive model based on machine learning and computer vision was developed to estimate arithmetic mean surface roughness (Ra) and maximum peak to valley height (Rz) of Ti6Al4V parts obtained by SPIF. An image database was prepared to train different classification algorithms in accordance with a supervised learning approach. A speeded up robust feature (SURF) detector was used to obtain visual vocabulary so that the classifiers are able to group the photographs into classes. The experimental results indicated that the proposed predictive method shows great potential to determine the surface quality, as classifiers based on a support vector machine with a polynomial kernel are suitable for this purpose.

The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

scholarly journals Study of Friction and Wear Effects in Aluminum Parts Manufactured via Single Point Incremental Forming Process Using Petroleum and Vegetable Oil-Based Lubricants

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3973
Author(s):  
José M. Diabb Zavala ◽  
Oscar Martínez-Romero ◽  
Alex Elías-Zúñiga ◽  
Héctor Manuel Leija Gutiérrez ◽  
Alejandro Estrada-de la Vega ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Friction And Wear ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Step Size ◽  
Vertical Step ◽  
Stribeck Curves

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, and Fourier-transform infrared spectroscopy (FTIR). Results show that during the SPIF process of the metallic specimens, soybean and corn oils attained the highest friction, along forces, roughness, and wear values. Based on the surface roughness measurements, it can be observed that soybean oil produces the worst surface roughness finish in the direction perpendicular to the tool passes (Ra =1.45 μm) considering a vertical step size of 0.25 mm with a 5 mm tool tip diameter. These findings are confirmed through plotting SPIFed Stribeck curves for the soybean and corn oils that show small hydrodynamic span regime changes for an increasing sample step-size forming process. This article elucidates the effects caused by mineral and vegetable oils on the surface of aluminum parts produced as a function of Single Point Incremental Sheet Forming process parameters.

scholarly journals Tribological Characterization of the Heat-Assisted Single Point Incremental Forming Process Applied to the Ti6Al4V Alloy with the Definition of An Adhesion Parameter for the Tool Surface

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7641
Author(s):  
Jesús Andrés Naranjo ◽  
Valentín Miguel ◽  
Juana Coello ◽  
María Carmen Manjabacas ◽  
Alberto Martínez-Martínez ◽  
...  
Keyword(s):  
Surface Finish ◽  
Incremental Forming ◽  
Single Point ◽  
Ti6al4v Alloy ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Tool Surface ◽  
Definition Of ◽  
Tribological Characterization

Heat-assisted single point incremental forming or HA-SPIF has a great potential for producing one-piece batches of hard-to-form materials such as Ti6Al4V alloy for medical and aeronautical applications. One of the limitations of the process is the difficulty in achieving a reasonable surface finish, which makes essential the characterization of the tribological process in the tool–sheet contact. In fact, not much work can be found at this point in literature. In this research, a novel procedure for evaluating the adhesion on the tool surface is proposed and the influence of the temperature is determined. The surface finish of parts is analyzed, and the changes promoted by HA-SPIF appearing in the morphology of the external surface layer are characterized by SEM.

Geometry Compensation Methods for Increasing the Accuracy of the SPIF Process

2021 ◽  
Vol 883 ◽  
pp. 217-224
Author(s):  
Yannick Carette ◽  
Marthe Vanhulst ◽  
Joost R. Duflou
Keyword(s):  
Control Strategy ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Calculation Methods ◽  
Forming Process ◽  
Complex Deformation ◽  
Commercial Use ◽  
Compensation Methods ◽  
Deformation Mechanics

Despite years of supporting research, commercial use of the Single Point Incremental Forming process remains very limited. The promised flexibility and lack of specific tooling is contradicted by its highly complex deformation mechanics, resulting in a process that is easy to implement but where workpiece accuracy is very difficult to control. This paper looks at geometry compensation as a viable control strategy to increase the accuracy of produced workpieces. The input geometry of the process can be compensated using knowledge about the deformations occurring during production. The deviations between the nominal CAD geometry and the actual produced geometry can be calculated in a variety of different ways, thus directly influencing the compensation. Two different alignment methods and three deviation calculation methods are explained in detail. Six combined deviation calculation methods are used to generate compensated inputs, which are experimentally produced and compared to the uncompensated part. All different methods are able to noticeably improve the accuracy, with the production alignment and closest point deviation calculation achieving the best results

Experimental Investigation of Single Point Incremental Forming of Aluminum Sheet in Groove Test

2017 ◽  
Vol 867 ◽  
pp. 177-183 ◽  
Author(s):  
Vikrant Sharma ◽  
Ashish Gohil ◽  
Bharat Modi
Keyword(s):  
Experimental Investigation ◽  
Incremental Forming ◽  
Single Point ◽  
Fractional Factorial ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Backing Plate ◽  
Groove Test ◽  
Factorial Design Of Experiments ◽  
Tool Diameter

Incremental sheet forming is one of the latest processes in sheet metal forming industry which has drawn attention of various researchers. It has shown improved formability compared to stamping process. Single Point Incremental Forming (SPIF) process requires only hemispherical tool and no die is required hence, it is a die-less forming process. In this paper experimental investigation on SPIF for Aluminium sheet has been presented. A groove test on Vertical Machining Centre has been performed. Factors (Step depth, Blank holder clamping area, Backing plate radius, Program strategy, Feed rate and Tool diameter) affecting the process are identified and experiments are carried out using fractional factorial design of experiments. Effect of the factors on fractured depth, forming time and surface finish have been analyzed using Minitab 17 software.

Sign in / Sign up

Export Citation Format

Share Document