scholarly journals Large-Eddy Simulation of a Laminar Separation Bubble

2019 ◽  
Vol 12 (3) ◽  
pp. 777-788
Author(s):  
N. K. Singh ◽  
Keyword(s):  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Laminar Separation Bubble ◽  
Laminar Separation ◽  
Eddy Simulation ◽  
Large Eddy

Detailed Numerical Characterization of the Suction Side Laminar Separation Bubble for a High-Lift Low Pressure Turbine Blade by Means of RANS and LES

2016 ◽  
Author(s):  
Fabio Bigoni ◽  
Stefano Vagnoli ◽  
Tony Arts ◽  
Tom Verstraete
Keyword(s):  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Laminar Separation Bubble ◽  
High Lift ◽  
Laminar Separation ◽  
Low Pressure Turbine ◽  
Eddy Simulation ◽  
Large Eddy

The scope of this work is to obtain a deep insight of the occurrence, development and evolution of the laminar separation bubble which occurs on the suction side of the high-lift T106-C low pressure turbine blade operated at correct engine Mach and Reynolds numbers. The commercial codes Numeca FINE/Turbo and FINE/Open were used for the numerical investigation of a set of three different Reynolds numbers. Two different CFD approaches, characterized by a progressively increasing level of complexity and detail in the solution, have been employed, starting from a steady state RANS analysis and ending with a Large Eddy Simulation. Particular attention was paid to the study of the open separation occurring at the lowest Reynolds number, for which a Large Eddy Simulation was performed in order to try to correctly capture the involved phenomena and their characteristic frequencies. In addition, the potentialities of the codes employed for the analysis have been assessed.

Computational Study of Flow Characteristics of Thick and Thin Airfoil With Implicit Large-Eddy Simulation at Low Reynolds Number

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
Kozo Fujii
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Laminar Separation Bubble ◽  
Laminar Separation ◽  
Eddy Simulation ◽  
Naca0012 Airfoil ◽  
Large Eddy ◽  
Implicit Large Eddy Simulation

The flow fields around NACA0012 and NACA0002 at Reynolds number of 23,000, and their aerodynamic characteristics are analyzed. Computations are conducted with implicit large-eddy simulation solver and Reynolds-averaged-Navier-Stokes solver. Around this Reynolds number, the flow over an airfoil separates, transits and reattaches, resulting in generation of a laminar separation bubble at angle of attack in the range of certain degrees. Over a NACA0012 airfoil a separation point moves toward its leading edge with increasing angle of attack, and a separated flow may transit to create a short bubble. On the other hand, over a NACA0002 airfoil a separation point is kept at its leading edge, and a separated flow may transit to create a long bubble. Moreover, there appears nonlinearity in lift curve for NACA0012 airfoil, but does not appear in that for NACA0002 in spite of existence of a laminar separation bubble.

scholarly journals Large-eddy simulation of laminar transonic buffet

2018 ◽  
Vol 850 ◽  
pp. 156-178 ◽  
Author(s):  
Julien Dandois ◽  
Ivan Mary ◽  
Vincent Brion
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Oscillation Amplitude ◽  
Boundary Layer Separation ◽  
Stream Velocity ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Shock Oscillation ◽  
Transonic Buffet

A large-eddy simulation of laminar transonic buffet on an airfoil at a Mach number $M=0.735$, an angle of attack $\unicode[STIX]{x1D6FC}=4^{\circ }$, a Reynolds number $Re_{c}=3\times 10^{6}$ has been carried out. The boundary layer is laminar up to the shock foot and laminar/turbulent transition occurs in the separation bubble at the shock foot. Contrary to the turbulent case for which wall pressure spectra are characterised by well-marked peaks at low frequencies ($St=f\cdot c/U_{\infty }\simeq 0.06{-}0.07$, where $St$ is the Strouhal number, $f$ the shock oscillation frequency, $c$ the chord length and $U_{\infty }$ the free-stream velocity), in the laminar case, there are also well-marked peaks but at a much higher frequency ($St=1.2$). The shock oscillation amplitude is also lower: 6 % of chord and limited to the shock foot area in the laminar case instead of 20 % with a whole shock oscillation and intermittent boundary layer separation and reattachment in the turbulent case. The analysis of the phase-averaged fields allowed linking of the frequency of the laminar transonic buffet to a separation bubble breathing phenomenon associated with a vortex shedding mechanism. These vortices are convected at $U_{c}/U_{\infty }\simeq 0.4$ (where $U_{c}$ is the convection velocity). The main finding of the present paper is that the higher frequency of the shock oscillation in the laminar regime is due to a different mechanism than in the turbulent one: laminar transonic buffet is due to a separation bubble breathing phenomenon occurring at the shock foot.

Large Eddy Simulation of Wake-Shear Layer Interactions Over a Multi-Element Aerofoil

2020 ◽  
Author(s):  
Souvik Naskar ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Modern commercial airliners use multi-element aerofoils to enhance take-off and landing performance. Further, multielement aerofoil configurations have been shown to improve the aerodynamic characteristics of wind turbines. In the present study, high resolution Large Eddy Simulation (LES) is used to explore the low Reynolds Number (Re = 0.832 × 104) aerodynamics of a 30P30N multi-element aerofoil at an angle of attack, α = 4°. In the present simulation, wake shed from a leading edge element or slat is found to interact with the separated shear layer developing over the suction surface of the main wing. High receptivity of shear layer via amplification of free-stream turbulence leads to rollup and breakdown, forming a large separation bubble. A transient growth of fluctuations is observed in the first half of the separation bubble, where levels of turbulence becomes maximum near the reattachment and then decay depicting saturation of turbulence. Results of the present LES are found to be in close agreement with the experiment depicting high vortical activity in the outer layer. Some features of the flow field here are similar to those occur due to interactions of passing wake and the separated boundary layer on the suction surface of high lift low pressure turbine blades.

Interactions of Separation Bubble With Oncoming Wakes by Large-Eddy Simulation

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
S. Sarkar ◽  
Harish Babu ◽  
Jasim Sadique
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Rotor Stator Interaction

The unsteady flow physics and heat transfer characteristics due to interactions of periodic passing wakes with a separated boundary layer are studied using large-eddy simulation (LES). A series of airfoils of constant thickness with rounded leading edge are employed to obtain the separated boundary layer. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model airfoils). This setup is a simplified representation of the rotor–stator interaction in turbomachinery. With a uniform inlet, the laminar boundary layer separates near the leading edge, undergoes transition due to amplification of disturbances, becomes turbulent, and finally reattaches forming a separation bubble. In the presence of oncoming wakes, the characteristics of the separated boundary layer have changed and the impinging wakes are found to be the mechanism affecting the reattachment. Phase-averaged results illustrate the periodic behavior of both flow and heat transfer. Large undulations in the phase-averaged skin friction and Nusselt number distributions can be attributed to the excitation of the boundary layer by convective wakes forming coherent vortices, which are being shed and convect downstream. Further, the transition of the separated boundary layer during the wake-induced path is governed by a mechanism that involves the convection of these vortices followed by increased fluctuations, where viscous effect is substantial.

Leading Edge Contamination of a C-D Compressor Blade Using Large Eddy Simulation

2020 ◽  
Author(s):  
S. Katiyar ◽  
S. Sarkar
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Suction Surface ◽  
Local Flow ◽  
Flow Acceleration ◽  
Eddy Simulation ◽  
Large Eddy

Abstract A large-eddy simulation (LES) is employed here to predict the flow field over the suction surface of a controlled-diffusion (C-D) compressor stator blade following the experiment of Hobson et al. [1]. When compared with the experiment, LES depicts a separation bubble (SB) in the mid-chord region of the suction surface, although discrepancies exist in Cp. Further, the LES resolves the growth of boundary layer over the mid-chord and levels of turbulence intensity with an acceptable limit. What is noteworthy that LES also resolves a tiny SB near the leading-edge at the designed inflow angle of 38.3°. The objective of the present study is to assess how this leading-edge bubble influences the transition and development of boundary layer on the suction surface before the mid-chord. It appears that the separation at leading-edge suddenly enhances the perturbation levels exciting development of boundary layer downstream. The boundary layer becomes pre-transitional followed by a decay of fluctuations up to 30% of chord attributing to the local flow acceleration. Further, the boundary layer appears like laminar after being relaxed from the leading edge excitation near the mid-chord. It separates again because of the adverse pressure gradient, depicting augmentation of turbulence followed by the breakdown at about 70% of chord.

Large-eddy simulation of turbulent flow over a parametric set of bumps

2019 ◽  
Vol 866 ◽  
pp. 503-525 ◽  
Author(s):  
Racheet Matai ◽  
Paul Durbin
Keyword(s):  
Large Eddy Simulation ◽  
Turbulent Flow ◽  
Pressure Gradient ◽  
Separation Bubble ◽  
Adverse Pressure Gradient ◽  
Windward Side ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy

Turbulent flow over a series of increasingly high, two-dimensional bumps is studied by well-resolved large-eddy simulation. The mean flow and Reynolds stresses for the lowest bump are in good agreement with experimental data. The flow encounters a favourable pressure gradient over the windward side of the bump, but does not relaminarize, as is evident from near-wall fluctuations. A patch of high turbulent kinetic energy forms in the lee of the bump and extends into the wake. It originates near the surface, before flow separation, and has a significant influence on flow development. The highest bumps create a small separation bubble, whereas flow over the lowest bump does not separate. The log law is absent over the entire bump, evidencing strong disequilibrium. This dataset was created for data-driven modelling. An optimization method is used to extract fields of variables that are used in turbulence closure models. From this, it is shown how these models fail to correctly predict the behaviour of these variables near to the surface. The discrepancies extend further away from the wall in the adverse pressure gradient and recovery regions than in the favourable pressure gradient region.

Wall-Modeled Large Eddy Simulation of Laminar and Turbulent Separation Bubble Flows

2016 ◽  
Author(s):  
Francois Cadieux ◽  
Jasim Sadique ◽  
Xiang I. Yang ◽  
Charles Meneveau ◽  
Rajat Mittal
Keyword(s):  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Eddy Simulation ◽  
Turbulent Separation ◽  
Large Eddy

Large Eddy Simulation of Turbulent Air Flow Over a Surface Mounted Hemisphere

2010 ◽  
Author(s):  
M. M. Tavakol ◽  
O. Abouali ◽  
M. Yaghoubi
Keyword(s):  
Experimental Data ◽  
Wind Tunnel ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Air Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Wind Tunnel Measurements ◽  
Turbulent Air Flow ◽  
Complex Features

Turbulent air flow around a surface mounted hemisphere is investigated numerically. The flow field has been simulated using Large Eddy Simulation (LES) technique. Using LES results, variations of flow velocity at various sections along the midplane are presented and compared with the wind tunnel measurements. Also the results of LES are compared with a RANS model (k-ε RNG). It is concluded that LES with the proper grid resolution is capable to capture the complex features of the flow especially in the separation bubble formed behind the hemisphere. The LES results are in a better agreement with experimental data compared with k-ε RNG model. Also various SGS models for LES technique are tested and the predictions of these models are compared.

Sign in / Sign up

Export Citation Format

Share Document