Possible approach to estimating the dispersion interaction in powder systems

2021 ◽  
Vol 3 ◽  
pp. 40-48
Author(s):  
A. M. Ayzenshtadt ◽  
◽  
E. V. Korolev ◽  
T. A. Drozdyuk ◽  
V. E. Danilov ◽  
...  
Keyword(s):  
Thin Film ◽  
Contact Angle ◽  
Transition Region ◽  
Raw Materials ◽  
Dispersion Interaction ◽  
Hamaker Constant ◽  
Film Bulk ◽  
Van Der Waals Effect ◽  
Selection Of ◽  
Wetting Liquid

In this paper, we present the results of testing the algorithm for calculating the Hamaker constant proposed by the authors as characteristics of the dispersion interaction according to experimental data obtained by studying the composition of fine powders of basalt and polymineral sand. For this purpose, based on a number of assumptions, the concept of an analogue Hamaker constant is introduced, which is an experimentally determined quantity.This parameter is recommended to be used when choosing the quantitative ratio of powder raw materials as a criterion for assessing the maximum possible van der Waals effect of dispersion interaction. An assumption was made about the presence of a constant characteristic of a thin film wetting the analyzed surface. Moreover, this thin film has a contact angle of the transition region “film-bulk phase”, the value of which is determined by the nature of the surface and the properties of the wetting liquid. The contact angle of the transition region can be an additional quantitative criterion for the selection of materials that are compatible in nature.

Epitaxial Growth of Sr0.3Ba0.7Nb2O6 Thin Films Prepared by Sol-Gel Process

1999 ◽  
Vol 606 ◽  
Author(s):  
Keishi Nishio ◽  
Jirawat Thongrueng ◽  
Yuichi Watanabe ◽  
Toshio Tsuchiya
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Epitaxial Growth ◽  
Raw Materials ◽  
Substrate Surface ◽  
Sol Gel ◽  
Tungsten Bronze ◽  
Monomethyl Ether ◽  
Tetragonal Tungsten Bronze ◽  
Sol Gel Process

AbstructWe succeeded in the preparation of strontium-barium niobate (Sr0.3Ba0.7Nb2O6 : SBN30)that have a tetragonal tungsten bronze type structure thin films on SrTiO3 (100), STO, or La doped SrTiO3 (100), LSTO, single crystal substrates by a spin coating process. LSTO substrate can be used for electrode. A homogeneous coating solution was prepared with Sr and Ba acetates and Nb(OEt)5 as raw materials, and acetic acid and diethylene glycol monomethyl ether as solvents. The coating thin films were sintered at temperature from 700 to 1000°C for 10 min in air. It was confirmed that the thin films on STO substrate sintered above 700°C were in the epitaxial growth because the 16 diffraction spots were observed on the pole figure using (121) reflection. The <130> and <310> direction of the thin film on STO were oriented with the c-axis in parallel to the substrate surface. However, the diffraction spots of thin film on LSTO substrate sintered at 700°C were corresponds to the expected pattern for (110).

BÖHLER W403 VMR

Alloy Digest ◽  
2013 ◽  
Vol 62 (9) ◽  
Keyword(s):  
Heat Treatment ◽  
Chemical Composition ◽  
Physical Properties ◽  
Tool Steel ◽  
Raw Materials ◽  
Heat Treating ◽  
Diffusion Annealing ◽  
Selection Of

Abstract Böhler (or Boehler) W403 VMR is a tool steel with outstanding properties, based not only on a modified chemical composition, but on the selection of highly clean raw materials for melting, remelting under vacuum (VMF), optimized diffusion annealing, and a special heat treatment. This datasheet provides information on composition, physical properties, and elasticity. It also includes information on forming and heat treating. Filing Code: TS-721. Producer or source: Böhler Edelstahl GmbH.

scholarly journals Selective normal mode excitation in multilayer thin film bulk acoustic wave resonators

2014 ◽  
Vol 105 (16) ◽  
pp. 162910 ◽  
Author(s):  
Andrey Kozyrev ◽  
Anatoly Mikhailov ◽  
Sergey Ptashnik ◽  
Peter K. Petrov ◽  
Neil Alford
Keyword(s):  
Thin Film ◽  
Acoustic Wave ◽  
Normal Mode ◽  
Bulk Acoustic Wave ◽  
Multilayer Thin Film ◽  
Mode Excitation ◽  
Film Bulk ◽  
Acoustic Wave Resonators ◽  
Bulk Acoustic Wave Resonators

scholarly journals The thin film bulk acoustic wave resonator based on single-crystalline 43○Y-cut lithium niobate thin films

AIP Advances ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 075002
Author(s):  
Xiaoyuan Bai ◽  
Yao Shuai ◽  
Lu Lv ◽  
Ying Xing ◽  
Jiaoling Zhao ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Lithium Niobate ◽  
Acoustic Wave ◽  
Bulk Acoustic Wave ◽  
Single Crystalline ◽  
Bulk Acoustic Wave Resonator ◽  
Wave Resonator ◽  
Film Bulk

scholarly journals Optimized genotyping method for identification of bacterial contaminants in pharmaceutical industry

2016 ◽  
Vol 66 (2) ◽  
pp. 289-295
Author(s):  
Borche Stamatoski ◽  
Miroslava Ilievska ◽  
Hristina Babunovska ◽  
Nikola Sekulovski ◽  
Sasho Panov
Keyword(s):  
Pharmaceutical Industry ◽  
Dna Sequencing ◽  
Bacterial Contamination ◽  
Raw Materials ◽  
Pcr Primers ◽  
Rrna Gene ◽  
Bacterial Identification ◽  
Bacterial Contaminants ◽  
Microbiological Control ◽  
Selection Of

AbstractMicrobiological control is of crucial importance in the pharmaceutical industry regarding the possible bacterial contamination of the environment, water, raw materials and finished products. Molecular identification of bacterial contaminants based on DNA sequencing of the hypervariable 16SrRNA gene has been introduced recently. The aim of this study is to investigate the suitability of gene sequencing using our selection of PCR primers and conditions for rapid and accurate bacterial identification in pharmaceutical industry quality control.DNA was extracted from overnight incubated colonies from 10 bacterial ATCC strains, which are common contaminants in the pharmaceutical industry. A region of bacterial 16SrRNA gene was analyzed by bidirectional DNA sequencing. Bacterial identification based on partial sequencing of the 16SrRNA gene is the appropriate method that could be used in the pharmaceutical industry after adequate validations. We have successfully identified all tested bacteria with more than 99 % similarity to the already published sequences.

Simulation and fabrication of thin film bulk acoustic wave resonator

2016 ◽  
Vol 37 (7) ◽  
pp. 074009
Author(s):  
Xixi Han ◽  
Yi Ou ◽  
Zhigang Li ◽  
Wen Ou ◽  
Dapeng Chen ◽  
...  
Keyword(s):  
Thin Film ◽  
Acoustic Wave ◽  
Bulk Acoustic Wave ◽  
Bulk Acoustic Wave Resonator ◽  
Wave Resonator ◽  
Film Bulk
Sign in / Sign up

Export Citation Format

Share Document