scholarly journals Comparison of thermophilic and mesophilic anaerobic treatment for potato processing wastewater using a contact reactor

2017 ◽  
Vol 19 (2) ◽  
pp. 318-326 ◽  
Keyword(s):  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Gas Production ◽  
Organic Loading ◽  
Potato Processing ◽  
Loading Rates ◽  
Methane Gas ◽  
Acid Ratio ◽  
Mesophilic Conditions ◽  
Better Than

In this study, different organic loading rates (OLRs) ranging from 1.1 to 5.0 kg COD/m3·day were used to assess the performance of an anaerobic reactor at the optimum mesophilic (35°C) and thermophilic (55°C) temperatures. The methane gas production rate of the thermophilic treatment was higher than that of the mesophilic treatment. The efficiency of chemical oxygen demand (COD) removal was observed to range from 89.12 to 93.20% following the thermophilic anaerobic treatment and from 76.36 to 92.62% following the mesophilic treatment. The average VFA (volatile fatty acid)/alkalinity ratio of the effluent was 0.3 under both thermophilic and mesophilic conditions for all the OLR applications. The HPr/HAc (propionic acid/acetic acid) ratio was calculated as 0.16 and 1.3 for the mesophilic and thermophilic treatments, respectively. For the mesophilic treatment, the average methane gas production was found to be 0.394 m3 CH4/kg CODremoved while it was 0.42 m3 CH4/kg CODremoved for the thermophilic experiment. However, the sludge settleability of the mesophilic treatment was better than that of the thermophilic treatment.

scholarly journals Optimization of the COD Removal Efficiency for a Static Granular Bed Reactor Treating Poultry Slaughterhouse Wastewater

2019 ◽  
Author(s):  
Zainab Rinquest ◽  
Moses Basitere ◽  
Maxwell Mewa-Ngongang ◽  
Seteno Karabo Obed Ntwampe ◽  
Mahomet Njoya
Keyword(s):  
South African ◽  
Removal Efficiency ◽  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Cod Removal ◽  
Granular Bed ◽  
Organic Loading ◽  
Loading Rates ◽  
Cod Removal Efficiency ◽  
Static Granular Bed Reactor

In this study, the efficiency of an anaerobic treatment system for wastewater from a South African poultry slaughterhouse was evaluated using a lab-scale static granular bed reactor (SGBR). The down-flow SGBR (2 L) was operated continuously for 138 days under mesophilic conditions (35-37 ˚C), at hydraulic retention times (HRTs) ranging from 24 to 96 h and average organic loading rates (OLRs) of 0.78 to 5.74 g COD/L.day. The SGBR achieved an average chemical oxygen demand (COD) removal efficiency of 80% and the maximum COD removal achieved was 95%, at an HRT of 24 h and average OLR of 5.74 g COD/L.day. The optimization of the SGBR, with regard to a suitable HRT and OLR, was determined using response surface methodology (RSM). The optimal SGBR performance with regard to the maximum COD removal efficiency was predicted for an OLR of 12.49 g COD/L.day and a HRT of 24 h, resulting in a 95.5% COD removal efficiency. The model R2 of 0.9638 indicated that the model is a good fit and is suitable to predict the COD removal efficiency for the SGBR.

Experiences with anaerobic treatment of fat-containing food waste liquids: two full scale studies with a novel anaerobic flotation reactor

2013 ◽  
Vol 69 (7) ◽  
pp. 1386-1394 ◽  
Author(s):  
C. T. M. J. Frijters ◽  
T. Jorna ◽  
G. Hesselink ◽  
J. Kruit ◽  
D. van Schaick ◽  
...  
Keyword(s):  
Food Waste ◽  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Gas Production ◽  
Cod Removal ◽  
Loading Rates ◽  
Study Results ◽  
New Type ◽  
High Concentrations ◽  
Volumetric Loading

Fat-containing food waste can be effectively treated in a new type of reactor, the so-called BIOPAQ-Anaerobic Flotation Reactor or BIOPAQ® anaerobic flotation reactor (AFR). In the reactor a flotation unit is integrated to retain the sludge. In this study results from two plants with a 430 and 511 m3-AFR, respectively, are presented. In one reactor, which is fed with water originating from different food liquid streams, over 99% of fat and oils were removed. Over 90% of the chemical oxygen demand (COD) was removed. When the last solids were removed from the effluent with a tilted plate settler, 98% COD removal was attained. The effluent concentrations of extractable hydrolysed and non-hydrolysed fats were less than 40 mg/l. Apparently the variations in the liquid streams deriving from the tank cleaning activities did not disturb the system. Only extremely high concentrations of fats could disturb the system, but the inhibition was reversible. In the reactor treating water from an ice-cream factory, which contained fats up to approximately 50% of influent COD, a COD removal efficiency of 90% was achieved. At volumetric loading rates varying from 1 to 8 kg COD/m3/d, biogas was produced at an average specific gas production of 0.69 m3/kg COD–removed.

Anaerobic co-digestion of winery waste and waste activated sludge: assessment of process feasibility

2013 ◽  
Vol 69 (2) ◽  
pp. 269-277 ◽  
Author(s):  
C. Da Ros ◽  
C. Cavinato ◽  
F. Cecchi ◽  
D. Bolzonella
Keyword(s):  
Activated Sludge ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Waste Activated Sludge ◽  
Organic Loading ◽  
Operational Conditions ◽  
Loading Rates ◽  
Thermophilic Conditions ◽  
Soluble Chemical Oxygen Demand

In this study the anaerobic co-digestion of wine lees together with waste activated sludge in mesophilic and thermophilic conditions was tested at pilot scale. Three organic loading rates (OLRs 2.8, 3.3 and 4.5 kgCOD/m3d) and hydraulic retention times (HRTs 21, 19 and 16 days) were applied to the reactors, in order to evaluate the best operational conditions for the maximization of the biogas yields. The addition of lee to sludge determined a higher biogas production: the best yield obtained was 0.40 Nm3biogas/kgCODfed. Because of the high presence of soluble chemical oxygen demand (COD) and polyphenols in wine lees, the best results in terms of yields and process stability were obtained when applying the lowest of the three organic loading rates tested together with mesophilic conditions.

scholarly journals Anaerobic treatment of glycerol for methane and hydrogen production

2013 ◽  
Vol 14 (2) ◽  
pp. 149-156 ◽  
Keyword(s):  
Hydrogen Production ◽  
Ph Value ◽  
Anaerobic Treatment ◽  
Microbial Culture ◽  
Batch Reactors ◽  
Continuous Stirred Tank Reactor ◽  
Organic Loading ◽  
Loading Rates ◽  
Fermentative Hydrogen Production ◽  
Initial Ph

This work focused on glycerol exploitation for biogas and hydrogen production. Anaerobic digestion of pure glycerol was studied in a continuous stirred tank reactor (CSTR), operated under mesophilic conditions (35oC) at various organic loading rates. The overall operation of the reactor showed that it could not withstand organic loading rates above 0.25 g COD L-1 d-1, where the maximum biogas (0.42 ± 0.05 L (g COD)-1) and methane (0.30 ± 0.04 L (g COD)-1) production were achieved. Fermentative hydrogen production was carried out in batch reactors under mesophilic conditions (35oC), using heat-pretreated anaerobic microbial culture as inoculum. The effects of initial concentration of glycerol and initial pH value on hydrogen production were studied. The highest yield obtained was 22.14 ± 0.46 mL H2 (g COD added)-1 for an initial pH of 6.5 and an initial glycerol concentration of 8.3 g COD L-1. The main metabolic product was 1.3 propanediol (PDO), while butyric and acetic acids as well as ethanol, at lower concentrations, were also determined.

scholarly journals Performance of Anaerobic Digestion of Acidified Palm Oil Mill Effluent under Various Organic Loading Rates and Temperatures

Water ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2432
Author(s):  
Muhammad Arif Fikri Hamzah ◽  
Peer Mohamed Abdul ◽  
Safa Senan Mahmod ◽  
Azratul Madihah Azahar ◽  
Jamaliah Md. Jahim
Keyword(s):  
Anaerobic Digestion ◽  
Palm Oil ◽  
Denaturing Gradient Gel Electrophoresis ◽  
Oxygen Demand ◽  
Microbial Community Analysis ◽  
Palm Oil Mill Effluent ◽  
Methane Formation ◽  
Organic Loading ◽  
Loading Rates ◽  
Palm Oil Mill

This study compared the performance of thermophilic and mesophilic digesters of an anaerobic digestion system from palm oil mill effluent (POME), in which temperature is a key parameter that can greatly affect the performance of anaerobic digestion. The digesters were incubated at two distinct temperatures of 55 and 37 °C, and operated with varying organic loading rates (OLRs) of 2.4, 3.2, and 4.0 g COD/L.d by altering the chemical oxygen demand (COD) of acidified POME during feeding. The results indicated that the performance of anaerobic digestion increased as the OLR increased from 2.4 to 4.0 g COD/L.d. At the OLR of 4.0 g COD/L.d, the thermophilic condition showed the highest methane yield of 0.31 ± 0.01 L/g COD, accompanied by the highest COD removal and volatile solid reduction, which were found to be higher than the mesophilic condition. Microbial community analysis via denaturing gradient gel electrophoresis (DGGE) revealed that Methanothermobacter sp. emerges as the dominant microbe, which is known to utilize the carbon dioxide pathway with hydrogen acting as an electron donor for methane formation

Anaerobic treatment of proteinaceous wastewater under mesophilic and thermophilic conditions

1999 ◽  
Vol 40 (1) ◽  
pp. 77-84 ◽  
Author(s):  
H. H. P. Fang ◽  
D. Wai-Chung Chung
Keyword(s):  
Bacterial Species ◽  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Anaerobic Sludge ◽  
Loading Rates ◽  
Batch Tests ◽  
Thermophilic Conditions ◽  
Anaerobic Sludge Blanket ◽  
Hydrolysis Of

Experiments were conducted in two 2.8 liter UASB (upflow anaerobic sludge blanket) reactors treating proteinaceous wastewaters at 37° and 55°C with 9 hours of hydraulic retention. Results showed that the mesophilic reactor consistently removed 83.5-85.1% of COD (chemical oxygen demand) at loading rates ranging 8-22 g COD l−1 d−1 (corresponding to 3000-8250 mg l−1 of proteinaceous COD in wastewater), whereas the thermophilic reactor removed only 68.5-82.7%. At 32 g COD l−1 d−1 (i.e. 12000 mg COD l−1), the removal efficiencies were lowered to 75.7% in the mesophilic reactor and 65.1% in the thermophilic reactor. At 42 g COD l−1 d−1, severe sludge washout occurred in the mesophilic reactor; at the same loading rate, the thermophilic reactor removed only 53.8% of COD even though sludge washout was under control. The degradation rate in the both reactors was limited by the initial hydrolysis of proteins. However, batch tests showed that thermophilic sludge had slightly higher methanogenic activities than mesophilic sludge in treating proteins and intermediate acids, except propionate. The sludge yields in mesophilic and thermophilic reactors were 0.066 and 0.099 g VSS g COD−1, respectively. Observations by scanning electron microscopy indicated that both types of sludge granules were of irregular shape. There was little noticeable difference between the two granules; both had neither a layered microstructure nor a predominant bacterial species.

Anaerobic treatment for C and S removal in “zero-discharge” paper mills: effects of process design on S removal efficiencies

2001 ◽  
Vol 44 (4) ◽  
pp. 189-195 ◽  
Author(s):  
J. B. van Lier ◽  
P. N.L. Lens ◽  
L. W. Hulshoff Pol
Keyword(s):  
Loading Rate ◽  
Anaerobic Treatment ◽  
Process Water ◽  
Uasb Reactor ◽  
Organic Loading ◽  
Production Rates ◽  
Paper Mills ◽  
Loading Rates ◽  
Zero Discharge ◽  
Uasb Reactors

Stringent environmental laws in Europe and Northern America lead to the development towards closure of the process water streams in pulp and paper mills. Application of a "zero-discharge" process is already a feasible option for the board and packaging paper industry, provided in-line treatment is applied. Concomitant energy conservation inside the mill results in process water temperatures of 50-60°C. Thermophilic anaerobic treatment complemented with appropriate post-treatment is considered as the most cost-effective solution to meet re-use criteria of the process water and to keep its temperature. In the proposed closed-cycle, the anaerobic treatment step removes the largest fraction of the biodegradable COD and eliminates “S” as H2S from the process stream, without the use of additional chemicals. The anaerobic step is regarded as the only possible location to bleed "S" from the process water cycle. In laboratory experiments, the effect of upward liquid velocity (Vupw) and the specific gas loading rate (Vgas) on the S removal capacity of thermophilic anaerobic bio-reactors was investigated. Acidifying, sulphate reducing sludge bed reactors were fed with partly acidified synthetic paper mill wastewater and were operated at 55°C and pH 6. The reactors were operated at organic loading rates up to 50 g COD.l−1.day−1 at COD/SO42- ratios of 10. The effect of Vupw was researched by comparing the performance of a UASB reactor operated at 1.0 m.h−1 and an EGSB reactor, operated at 6.8 m.h−1. The Vupw had a strong effect on the fermentation patterns. In the UASB reactor, acidification yielded H2, acetate and propionate, leading to an accumulation of reducing equivalents. These were partly disposed of by the production of n-butyrate and n-valerate from propionate. In the EGSB reactor net acetate consumption was observed as well as high volumetric gas (CO2 and CH4) production rates. The higher gas production rates in the EGSB reactor resulted in higher S-stripping efficiencies. The effect of Vgas was further researched by comparing 2 UASB reactors which were sparged with N2 gas at a specific gas loading rate of 30 m3.m−2.day−1. In contrast to the regular UASB reactors, the gas-supplied UASB showed a more stable performance when the organic loading rates were increased. Also, the H2S stripping efficiency was 3-4 times higher in the gas-supplied UASB, reaching values of 67%. Higher values were not obtained owing to the relatively poor sulphate reduction efficiencies.

Potato Processing Wastewater Treatment at Relatively High Loading Rates Using a Unified Anaerobic Fermenter-Filter

1982 ◽  
Vol 17 (1) ◽  
pp. 63-74 ◽  
Author(s):  
R.C. Landine ◽  
G.J. Brown ◽  
A.A. Cocci ◽  
T. Viraraghavan
Keyword(s):  
Wastewater Treatment ◽  
Room Temperature ◽  
Anaerobic Treatment ◽  
Basic Design ◽  
Potato Processing ◽  
Two Stage ◽  
Filter System ◽  
Loading Rates ◽  
Laboratory Bench ◽  
Scale Design

Abstract A laboratory bench-scale study using a unified anaerobic fermenter-filter system (referred to as a BVF-HAF system) was conducted at room temperature over an 8 month period on potato processing wastewater for the purpose of verifying a proposed full-scale design concept. In addition to two-stage anaerobic treatment, the first stage anaerobic effluent (BVF effluent) was subjected to aerobic polishing in a simulated facultative aerated lagoon with a retention of 4 days. The basic design conditions entailed treatment of a clarified potato wastewater with a COD of 7600 mg/L and a retention of 4 d in the BVF (loading 1.71 kg/m3.d). After over-coming an upset condition believed due to toxicity of the vacuum filtrate feed, the model performed well achieving 78.9% COD removal in the BVF plus 5 3.4% in the HAF for a combined total of 90.2%. When the BVF effluent was aerated the combined BVF - aerated lagoon removal reached 94.8%.

scholarly journals Dolomitic limestone as an alkalizing agent for treating cassava starch wastewater in an anaerobic reactor

Revista CERES ◽  
2018 ◽  
Vol 65 (5) ◽  
pp. 388-394
Author(s):  
Denise Palma ◽  
Julia Piechontcoski Fernandes ◽  
Marney Pascoli Cereda ◽  
Simone Damasceno Gomes
Keyword(s):  
Oxygen Demand ◽  
Cassava Starch ◽  
Total Alkalinity ◽  
Dolomitic Limestone ◽  
Organic Loading ◽  
Reactor Operation ◽  
Anaerobic Reactor ◽  
Loading Rates ◽  
Volatile Acidity ◽  
Starch Wastewater

ABSTRACT Cassava processing wastewater has a low Volatile Acidity/Total Alkalinity ratio, low buffering capacity and became quickly acidified. In this trial, dolomitic limestone was used as an alkalizing agent in an anaerobic reactor to treat cassava starch wastewater. The dolomitic limestone contained 27% CaO and 23% MgO and granulometry between 24.5 and 38.1 mm. The average Chemical Oxygen Demand of the wastewater was 13331.30 mgO2 L-1, the organic loading rates (OLR) ranged from 1.23 to 16.43 gCOD L-1 d-1 and the hydraulic retention times ranged from 10.00 to 0.80 days. The results showed that the calcium concentrations increased in the reactor effluent and the magnesium concentrations decreased as the organic loading rates increased. Ca2+ and Mg2+ concentrations were approximately 5,000 and 5.05 times greater in the sludge than in the inoculum, respectively. The average pH, Total alcalinity, Volatile Acidity and Volatile Acidity/ Total alcalinity values were 6.69, 882.54 mgCaCO3 L-1, 221.55 mgCH3COOH L-1 and 0.22, respectively. The loss of limestone mass corresponded to only 2.51% of the initial mass, after 134 days of anaerobic reactor operation. Finally, it was concluded that the limestone effectively controlled acidification through the alkalinity increased in the system.

Start-Up Strategy to Achieve Excellent Efficiency of Degradation Acetate,Ethanol and Propionate in UASB

2011 ◽  
Vol 71-78 ◽  
pp. 2103-2106
Author(s):  
Ming Yue Zheng ◽  
Ming Xia Zheng ◽  
Kai Jun Wang ◽  
Hai Yan
Keyword(s):  
Loading Rate ◽  
Anaerobic Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Organic Loading ◽  
Metabolic Intermediate ◽  
Loading Rates ◽  
Start Up ◽  
Anaerobic Sludge Blanket

The performance of upflow anaerobic sludge blanket (UASB) fed with three metabolic intermediate (acetate, ethanol, and propionate) respectively was studied. The degradation of metabolic intermediate were investigated to discuss the reason for propionate inhibition problem in anaerobic treatment. The hydraulic retention time (HRT) in the reactors started with 8.0h.The yield rate of biogas were 237ml/gCOD, 242ml/gCOD, 218ml/gCOD for acetate, ethanol and propionate, respectively when finishing start-up under OLR of 5.0 kgCOD/(m3·d) (HRT=9.6h).The HRT remained constant 9.6h,and the substrate concentration was gradually increased from 1,000 to 16,000mg/L as COD,and the organic loading rates(OLR) was from 3.0 to 40.0 kgCOD/(m3·d).The maximum propionate concentration was 41.6 gHPr-COD/L at the organic loading rate of 43.9 kgCOD/(m3·d) (HRT, 9.6h) as well as acetate and ethanol.

Sign in / Sign up

Export Citation Format

Share Document