scholarly journals Techno-Economic Analysis of the placement of the Capacitor in the Integrated Nepal Power System

2021 ◽  
Vol 1 (1) ◽  
pp. 9-15
Author(s):  
Manisha Shahi Thakuri ◽  
Hari Bahadur Darlami
Keyword(s):  
Power System ◽  
Power Flow ◽  
Reactive Power ◽  
Optimal Size ◽  
Voltage Profile ◽  
Voltage Level ◽  
Load Demand ◽  
Optimum Placement ◽  
Reduction Strategies ◽  
Flow Study

With the increasing load demand, Integrated Nepal Power System (INPS) is facing a stiff challenge to maintain voltage profile within the standards and reduce system loss. Among the loss reduction strategies, an immediate solution would be installation of reactive power compensators at the grid substations. The power flow study of existing system is performed and a genetic algorithm is used to find optimum placement of suitable size of the capacitor banks to be added in system. 6 substations with a total reactive power supply of 80 MVAR was determined as optimal size and location and the installation is also financially feasible. Moreover, the analysis of capacitors placed at the varying voltage levels implied that the most suitable voltage level for the capacitor installation is 11kV.

scholarly journals Voltage Profile Improvement with Combined UPFC and IPFC Facts Devices: A Review

2020 ◽  
Vol 1 (1) ◽  
pp. 26-30
Author(s):  
Violet Kaswii ◽  
Michael Juma Saulo
Keyword(s):  
Power System ◽  
Power Flow ◽  
Reactive Power ◽  
Voltage Control ◽  
System Stability ◽  
Voltage Profile ◽  
Transmission Systems ◽  
Facts Devices ◽  
Flow Controller ◽  
Power Flow Controller

The interline power flow controller (IPFC) and the unified power flow controller (UPFC) are both advanced types of flexible AC transmission systems (FACTS). These devices can provide the power system with control of voltage, and that of real and reactive power. This paper reviews the literature on UPFC and IPFC FACTS devices in voltage control and covers two main areas of research (i) voltage control using FACTS devices, and (ii) UPFCs / IPFCs and their applications in power systems. FACTs devices are applied in modern power system networks for the purpose of voltage control while at the same time providing enhanced power system stability. Research has shown that their benefits in the long run outweighs their high cost especially when they are optimally sized and located in the power network. Moreover, in the planning of power transmission systems, a Multi-Criteria Decision Making (MCDM) technique can help in the incorporation of both the costs and technical viability. This approach provides techno-economic optimization and at the same time meeting environmental criteria.

scholarly journals Optimal placement of facts devices to reduce power system losses using evolutionary algorithm

2021 ◽  
Vol 21 (3) ◽  
pp. 1271
Author(s):  
Mahmood Khalid Zarkani ◽  
Ahmed Sahib Tukkee ◽  
Mohammed Jasim Alali
Keyword(s):  
Power System ◽  
Evolutionary Algorithm ◽  
Power Flow ◽  
Reactive Power ◽  
Research Work ◽  
Test System ◽  
Optimal Placement ◽  
Unified Power Flow Controller ◽  
Voltage Profile ◽  
Facts Devices

<p>The rapid and enormous growths of the power electronics industries have made the flexible AC transmission system (FACTS) devices efficient and viable for utility application to increase power system operation controllability as well as flexibility. This research work presents the application of an evolutionary algorithm namely differential evolution (DE) approach to optimize the location and size of three main types of FACTS devices in order to minimize the power system losses as well as improving the network voltage profile. The utilized system has been reactively loaded beginning from the base to 150% and the system performance is analyzed with and without FACTS devices in order to confirm its importance within the power system. Thyristor controlled series capacitor (TCSC), unified power flow controller (UPFC) and static var compensator (SVC) are used in this research work to monitor the active and reactive power of the carried out system. The adopted algorithm has been examined on IEEE 30-bus test system. The obtained research findings are given with appropriate discussion and considered as quite encouraging that will be valuable in electrical grid restructuring.</p>

Economic Load Dispatch

2018 ◽  
pp. 46-64 ◽  
Keyword(s):  
Power System ◽  
Power Flow ◽  
Optimal Power Flow ◽  
Reactive Power ◽  
Transmission Loss ◽  
Electric Energy ◽  
Voltage Profile ◽  
Fuel Cost ◽  
Voltage Deviation ◽  
Fuel Cost Minimization

The main objective of the power system is to deliver electric energy to its loads economically and efficiently in a safe and reliable manner. Due to the complicated structure of the present power system network and competitive environment introduced by deregulation, optimal power flow (OPF) and optimal reactive power flow (ORPD) provide efficient exploitation of existing power generations. This chapter describes the detail problem formulation of OPF and ORPD problems. In this study, three different single objectives, namely fuel cost minimization, voltage profile improvement, and transmission loss minimization, are considered. Moreover, in order to judge the effectiveness of the proposed methods for multi-objective scenario, two bi-objectives, namely simultaneous minimization of fuel cost and voltage deviation; simultaneous minimization of fuel cost and transmission loss; and one tri-objective function, namely simultaneous minimization of fuel cost with voltage deviation and loss, are considered.

Optimal location of interline power flow controller in a power system network using ABC algorithm

2013 ◽  
Vol 62 (1) ◽  
pp. 91-110 ◽  
Author(s):  
S. Sreejith ◽  
Sishaj Psimon ◽  
M.P. Selvan
Keyword(s):  
Power System ◽  
Transmission Lines ◽  
Power Flow ◽  
Reactive Power ◽  
Optimal Location ◽  
Voltage Profile ◽  
Optimal Position ◽  
Flow Controller ◽  
Power Flow Controller ◽  
Installation Cost

Abstract This paper proposes a methodology based on installation cost for locating the optimal position of interline power flow controller (IPFC) in a power system network. Here both conventional and non conventional optimization tools such as LR and ABC are applied. This methodology is formulated mathematically based on installation cost of the FACTS device and active power generation cost. The capability of IPFC to control the real and reactive power simultaneously in multiple transmission lines is exploited here. Apart from locating the optimal position of IPFC, this algorithm is used to find the optimal dispatch of the generating units and the optimal value of IPFC parameters. IPFC is modeled using Power Injection (PI) model and incorporated into the problem formulation. This proposed method is compared with that of conventional LR method by validating on standard test systems like 5-bus, IEEE 30-bus and IEEE 118-bus systems. A detailed discussion on power flow and voltage profile improvement is carried out which reveals that incorporating IPFC into power system network in its optimal location significantly enhance the load margin as well as the reliability of the system.

Selecting Optimal Reactive Compensation Device for Power System

2014 ◽  
Vol 556-562 ◽  
pp. 1560-1563
Author(s):  
Tran Thi Ngoat ◽  
Xiao Ming Zha ◽  
Le Ngoc Giang
Keyword(s):  
Power System ◽  
Power Flow ◽  
Transient Stability ◽  
Reactive Power ◽  
Transient State ◽  
Power Generating Unit ◽  
Load Demand ◽  
Reactive Compensation ◽  
Compensation Device ◽  
Selection Of

Although there are many studies on application of FACTS unit, especially application of reactive power generating unit for power system to enhance voltage stability amplitude and transient stability as considered, the evaluation and selection of suitable power generating unit (STATCOM or SVC) as well as optimal compensation size in the analysis of steady and transient state is not paid attention to. This article studies the above described issues to give a solution to install reasonable reactive power generating source (kind of Var source, location, size) for the power system. The analysis will be based on the technical factors rather than economic ones. 500kV grid system in Vietnam will be used in the calculation until 2015. To deeply evaluate, the implementation plan of reactive power compensation was only studied for 500kV grid in the South, where the load demand is large and can be dramatically increased. The results of power flow calculation, the analysis of characteristics of PV, OPF, and transient stability were studied through PSS/E-30 software.

scholarly journals Enhancement of Voltage Stability by Using SVC for 30-Bus Power System

2019 ◽  
Vol 4 (2) ◽  
pp. 128-136
Author(s):  
Dara Hama Amin
Keyword(s):  
Power System ◽  
Voltage Stability ◽  
Reactive Power ◽  
Sensitivity Factor ◽  
Voltage Sensitivity ◽  
Voltage Profile ◽  
Voltage Level ◽  
Facts Devices ◽  
Before And After ◽  
The Stability

Voltage stability refers to maintaining the value of the voltage in all busses of the electric network at a steady level (initial operating point) during any sudden disturbance. Voltage instability may happen due to an increase in the demand of the load or in case of any change in the reactive power, thus, the system will go into uncontrollable and unstoppable decline in the voltage level. The effect of Static Var Compensator (SVC) on voltage stability is discussed in the paper, as well as the improvement of the voltage profile. Usually, SVC and FACTS devices were used for enhancing the voltage level profile and so the stability. Choosing the optimal location for the FACTS devices is essential due to its expensive costs. This paper used sensitivity factor to helpful to determine the most correct placement of FACTS devices in the system. Simulations are performed on Kurdistan Region 30-bus Power System using MATLAB-PSAT tool. As a result, the voltage of all 30 buses calculated. Based on the “voltage sensitivity factor”, the nominated weak buses has been marked which are suitable for placing the FACTS devices in order to improve the limits of the voltage stability of the system. Moreover, depending on the obtained optimal locations, a full analysis of the voltage and powers for the system has applied in two cases, before and after placing SVC respectively which is result in notable stability improvement and losses reduction.

scholarly journals Selection the optimum place of FACTS devices using fuzzy control system

2020 ◽  
Vol 11 (4) ◽  
pp. 1805
Author(s):  
Jawad Hameed ◽  
Hameed Ali Mohammed ◽  
Amer T. Saeed
Keyword(s):  
Power System ◽  
Reactive Power ◽  
Flow Index ◽  
Voltage Profile ◽  
Flexible Ac Transmission ◽  
Optimum Placement ◽  
Facts Controllers ◽  
Remedial Actions ◽  
The Stability ◽  
Ac Transmission

In this paper, the voltage stability of the power system is studied during fault conditions. Enhancement of the system’s stability will be achieved by utilizing Flexible AC transmission systems (FACTS) controllers at the best place in the system. The optimum placement of (FACTS) controllers occurred on the most affected bus by the fault in the system (weakest bus). Two approaches have been used in this study to effectively obtain the best location of the (FACTS) controllers in the system. The first method is based on computing the deviation which occurs in the active power and reactive power due to the fault at each load bus at a time. Whereas the second method is performed through exploiting a MATLAB fuzzy set technique utilizing two indices: Line Flow Index (LFI) and Voltage Profile Index (VPI) during fault and steady-state conditions. The results show that both of these indices resulted in the same bus as the best location. Remedial actions in the attempt at improving in the stability of the power system are discussed taking the advantage of using (FACTS) compensation (SVC) and (STATCOM) at the most vulnerable system buses. In this work, MATLAB program with an IEEE 24 bus system is examined.

scholarly journals IMPACT OF STATIC VAR COMPENSATORS ON POWER SYSTEM: A CASE STUDY

2014 ◽  
pp. 4-8
Author(s):  
GUNEET KOUR ◽  
G.S. BRAR ◽  
JASWANTI JASWANTI
Keyword(s):  
Power System ◽  
Power Electronics ◽  
Power Flow ◽  
Reactive Power ◽  
Flow Analysis ◽  
Load Flow ◽  
Voltage Profile ◽  
Flexible Control ◽  
Load Flow Analysis ◽  
Reactive Power Flow

With increase in load, any transmission, distribution and generating model suffers from disturbances. These disturbances effect the overall stability of the system. Criterias like voltage profile, power flows, losses tell us about the state of the system under study. Load flow analysis of the system under study is capable of providing the insight of the system. The Emergence of FACTS device is really a step forward for the flexible control or Power System Operations. FACTS is the name given to the application of the power electronics devices to control power flows and other quantities in the power system. But when it comes to implementation stage, optimizing the location becomes a great concern because of the high cost involved with FACTS devices especially converter like SVC, STATCOM etc. Static Var Compensator (SVC) is a power quality device, which employs power electronics to control the reactive power flow of the system where it is connected. It is able to provide fast-acting reactive power compensation on electrical systems. SVC is one of the methods and can be applied to obtain a system with least losses, increased power flow and healthy voltage profile. Number, location and size of SVC are the main concerns and they can be optimized to a great extent by Genetic Algorithm (GA) or any other method. Use of SVC in a system has shown considerable increase in voltage profile and power flows while decrease in losses.

scholarly journals Penempatan Kapasitor Shunt Pada Sistem Kelistrikan 150 kV Sulselrabar

2018 ◽  
Vol 2 (2) ◽  
pp. 64
Author(s):  
Muhammad Ruswandi Djalal ◽  
Herman HR
Keyword(s):  
Normal Condition ◽  
Power Flow ◽  
Reactive Power ◽  
Critical Conditions ◽  
Critical Voltage ◽  
Voltage Profile ◽  
Calculation Results ◽  
Simulation Results ◽  
Flow Study ◽  
Better Than

 Power flow study is the determination or calculation of the voltage, current and power factor or reactive power that is present at various points in a power grid in the normal state, whether current or expected to occur in the future. From the result of normal condition analysis, it is obtained the critical voltage profile on bus 31 tonasa and used as the candidate for mounting capacitor. From the calculation results obtained capacities installed 16.0413 Mvar. From the simulation results before the installation and after installation of the capacitor visible improvement of voltage profile and channel losses. The channel losses prior to installation are 32,649 MW and after installation of 31,834 MW. For voltage profiles, some buses also look better, than before in critical conditions to be marginal. On the previous bus tonasa 0.933 pu to 0.953043 pu. 

Application of UPFC for enhancement of voltage profile and minimization of losses using Fast Voltage Stability Index (FVSI)

2012 ◽  
Vol 61 (2) ◽  
pp. 239-250 ◽  
Author(s):  
M. Kumar ◽  
P. Renuga
Keyword(s):  
Power System ◽  
Voltage Stability ◽  
Reactive Power ◽  
Optimization Technique ◽  
Optimal Solution ◽  
Stability Index ◽  
Test System ◽  
Unified Power Flow Controller ◽  
Voltage Profile ◽  
Voltage Stability Index

Application of UPFC for enhancement of voltage profile and minimization of losses using Fast Voltage Stability Index (FVSI)Transmission line loss minimization in a power system is an important research issue and it can be achieved by means of reactive power compensation. The unscheduled increment of load in a power system has driven the system to experience stressed conditions. This phenomenon has also led to voltage profile depreciation below the acceptable secure limit. The significance and use of Flexible AC Transmission System (FACTS) devices and capacitor placement is in order to alleviate the voltage profile decay problem. The optimal value of compensating devices requires proper optimization technique, able to search the optimal solution with less computational burden. This paper presents a technique to provide simultaneous or individual controls of basic system parameter like transmission voltage, impedance and phase angle, thereby controlling the transmitted power using Unified Power Flow Controller (UPFC) based on Bacterial Foraging (BF) algorithm. Voltage stability level of the system is defined on the Fast Voltage Stability Index (FVSI) of the lines. The IEEE 14-bus system is used as the test system to demonstrate the applicability and efficiency of the proposed system. The test result showed that the location of UPFC improves the voltage profile and also minimize the real power loss.

Sign in / Sign up

Export Citation Format

Share Document