Size-Dependent Stability of a Cantilevered Piezoelectrically Actuated Micropipe Conveying Fluid

Size-dependent effects of a cantilevered piezoelectrically actuated micropipe conveying fluid are investigated. Based on the modified strain gradient beam theory, the model of system is obtained using Hamilton's principle. The motion equation is discretized into ordinary differential equations by Generalized Differential Quadrature Method (GDQM). A stability analysis of the system is completed through eigenvalue analysis. Numerical results show the effect of geometrical shape size, and length scale parameters on critical flow velocity, and critical voltage. Results prove that the modified strain gradient theory (MSGT) has a higher critical flow velocity and critical voltage than predicted by modified couple stress theory (MCST) and classical theory (CT).

Application of large-scale grid-connected solar photovoltaic system for voltage stability improvement of weak national grids

This paper investigates the application of large-scale solar photovoltaic (SPV) system for voltage stability improvement of weak national grids. Large-scale SPV integration has been investigated on the Nigerian power system to enhance voltage stability and as a viable alternative to the aged shunt reactors currently being used in the Nigerian national grid to mitigate overvoltage issues in Northern Nigeria. Two scenarios of increasing SPV penetration level (PL) are investigated in this work, namely, centralized large-scale SPV at the critical bus and dispersed large-scale SPV across the weak buses. The voltage stability of the system is evaluated using the active power margin (APM) also called megawatt margin (MWM) derived from Active Power–Voltage (P–V) analysis, the reactive power margin (RPM) and the associated critical voltage–reactive power ratio (CVQR) index obtained from Reactive Power–Voltage (Q–V) analysis. All simulations are carried out in DIgSILENT PowerFactory software and result analyses done with MATLAB. The results show that with centralized SPV generation for the case study system, the highest bus voltage is able to fall within acceptable limits at 26.29% (1000 MW), while the dispersed SPV achieves this at 21.44% (800 MW). Also, the dispersed SPV scenario provides better voltage stability improvement for the system as indicated by the MWM, RPM and the CVQR index of the system. Therefore, this work provides a baseline insight on the potential application of large-scale SPV in weak grids such as the Nigerian case to address the voltage stability problems in the power system while utilizing the abundant solar resource to meet the increasing energy demand.

Electroconvection near an ion-selective surface with Butler–Volmer kinetics

We study the effects of interfacial kinetics on the electro-hydrodynamics of ion transport near an ion-selective surface using a combination of linear stability analysis and numerical simulation. The finite kinetics of the electrolyte–electrode interface affects the ion transfer and electroconvection in many ways. On a surface of fixed topography, such as a metal surface of slow and stable ion deposition or covered by a polymer membrane, the finite kinetics reduces the current in one-dimensional ion diffusion/migration, increases the critical voltage for the onset of the electroconvective instability, changes the dynamics of the electroconvection and the overlimiting current, and enhances the lateral ion diffusion within the interfacial layer. The first three effects are indirectly caused by the reaction kinetics and can be characterized by an effective voltage difference across the liquid electrolyte. In comparison, the last effect is controlled by a direct interplay between kinetics and nonlinear electroconvection. Scaling laws for ion transport and features of electroconvection are proposed. We also analyse the linear stability of a surface which evolves under ion deposition and find that the finite kinetics decreases the growth rate of both electroconvective and morphological instabilities and therefore modifies the wavenumber of the most unstable mode.

Operando structural investigations of thermoelectric materials

Operando characterization provides direct insight into material response under application conditions and it is essential to understand the stability limits of thermoelectric materials and their decomposition mechanisms. An operando setup capable of maintaining a thermal gradient while running DC current through a bar-shaped sample has been developed. Under operating conditions, X-ray scattering data can be measured along the sample to obtain spatially resolved structural knowledge in concert with measurement of electrical resistance and the Seebeck coefficient. Here thermoelectric β-Zn4Sb3, which is a mixed ionic–electronic conductor, is studied, and a significant temperature dependence of the Zn migration is directly observed. Measurements with the thermal gradient applied either along or opposite to the DC current establish that the ion migration is an electrochemical effect rather than a thermodiffusion. Consideration of only the applied critical voltage or current density is insufficient for deducing the stability limits and structural integrity of materials with temperature-dependent ion mobility. The present operando setup is not limited to studies of thermoelectric materials, and it also lends itself to studies of, for example, ion diffusion in solid-state electrolytes or structural transformations in solid-state reactions.

Attempt to Describe Phase Slips by Means of an Adiabatic Approximation

As a plausibility test for the feasibility of extension of the quasiclassical Keldysh–Usadel technique to slowly varying situations, we assess the influence of the time-derivative term in the time-dependent Ginzburg–Landau equation. We consider cases in which the superconducting state in a nanowire varies slowly, either because the voltage applied on it is small, or because most of phase drift takes place next to the boundaries. An approximation without this time derivative can describe the superconducting state away from phase slips, but is unable to predict the value or the existence of a critical voltage at which evolution becomes non-stationary.

On the Electro-Mechanical Stability of Elastomeric Coaxial Fibers

The stability of cylindrical coaxial fibers made from soft elastomeric materials is studied for electro-static loadings. The general configuration considered is a three-component axisymmetric fiber having a conducting core bonded to a dielectric annulus in turn bonded to an outer conducting annular sheath. A voltage difference between the conducting components is imposed. The stresses and actuated elongation in the perfectly concentric fiber are analyzed, and the critical voltage at which stability of the concentric configuration is lost is determined via solution of the non-axisymmetric bifurcation problem. The role of the geometry and moduli contrasts among the components is revealed, and the sub-class of two-component fibers is also analyzed. The idealized problem of a planar layer with conducting surfaces that is bonded to a stiff substrate on one surface and free on the other exposes the importance of short wavelength surface instability modes.

Experimental Study on Ultrasonic Vibration-Assisted WECDM of Glass Microstructures with a High Aspect Ratio

With the rapid development of micro-electro-mechanical systems (MEMSs), the demand for glass microstructure is increasing. For the purpose of achieving high quality and stable machining of glass microstructures with a high aspect ratio, ultrasonic vibration is applied into the micro-wire electrochemical discharge machining (WECDM), which is proposed as ultrasonic vibration-assisted WECDM with a micro helical electrode. Firstly, the formation of a gas film on the surface of the helical electrode in WECDM machining is simulated, meaning the thickness of the gas film can be reduced by adding suitable ultrasonic amplitude, thus reducing the critical voltage, then the machining localization and stability were enhanced. Then, the micro helical electrode with a diameter of 100 μm is used to carry out sets of experiments that study the influence of ultrasonic amplitude, machining voltage, duty factor, pulse frequency, and feed rate on the slit width. The experimental results show that the machining stability and quality are significantly improved by adding suitable ultrasonic amplitude. When the amplitude was 5.25 μm, the average slit width was reduced to 128.63 μm with a decrease of 20.78%. Finally, with the optimized machining parameters, micro planar coil structure and microcantilever structure with a high aspect ratio were fabricated successfully on the glass plate. It is proved that ultrasonic vibration-assisted WECDM with the micro helical electrode method can meet the requirements of high aspect ratio microstructure machining for hard and brittle materials.

Impact of Battery Energy Storage System and its Converter Characteristics on Voltage Sags

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.