scholarly journals NUMERICAL STUDIES ON LATERAL BRACING METHOD WITH EFFECTIVE RESTRAINT ON OUT-OF-PLANE DEFORMATION OF WIDE FLANGE BEAM

2015 ◽  
Vol 80 (714) ◽  
pp. 1319-1327
Author(s):  
Zheng YU ◽  
Ryunosuke KAWAI ◽  
Iori KANAO
Keyword(s):  
Plane Deformation ◽  
Numerical Studies ◽  
Out Of Plane ◽  
Lateral Bracing ◽  
Flange Beam

scholarly journals Characterization and ballistic performance of thin pre-damaged resin-starved aramid-fiber composite panels

2021 ◽  
pp. 004051752110134
Author(s):  
Cerise A Edwards ◽  
Stephen L Ogin ◽  
David A Jesson ◽  
Matthew Oldfield ◽  
Rebecca L Livesey ◽  
...  
Keyword(s):  
Fiber Composite ◽  
Plane Deformation ◽  
Ballistic Impact ◽  
Image Correlation ◽  
Composite Panel ◽  
Composite Panels ◽  
Micro Computed Tomography ◽  
Ballistic Performance ◽  
Low Level ◽  
Out Of Plane

Military personnel use protective armor systems that are frequently exposed to low-level damage, such as non-ballistic impact, wear-and-tear from everyday use, and damage during storage of equipment. The extent to which such low-level pre-damage could affect the performance of an armor system is unknown. In this work, low-level pre-damage has been introduced into a Kevlar/phenolic resin-starved composite panel using tensile loading. The tensile stress–strain behavior of this eight-layer material has been investigated and has been found to have two distinct regions; these have been understood in terms of the microstructure and damage within the composite panels investigated using micro-computed tomography and digital image correlation. Ballistic testing carried out on pristine (control) and pre-damaged panels did not indicate any difference in the V50 ballistic performance. However, an indication of a difference in response to ballistic impact was observed; the area of maximal local out-of-plane deformation for the pre-damaged panels was found to be twice that of the control panels, and the global out-of-plane deformation across the panel was also larger.

scholarly journals In-Process Measurement of Three-Dimensional Deformations Based on Speckle Photography

2021 ◽  
Vol 11 (11) ◽  
pp. 4981
Author(s):  
Andreas Tausendfreund ◽  
Dirk Stöbener ◽  
Andreas Fischer
Keyword(s):  
Evaluation Method ◽  
Process Analysis ◽  
Plane Deformation ◽  
Three Dimensional ◽  
Machining Process ◽  
Image Correlation ◽  
Speckle Photography ◽  
Process Measurement ◽  
Out Of Plane ◽  
Plane Deformations

In the concept of the process signature, the relationship between a material load and the modification remaining in the workpiece is used to better understand and optimize manufacturing processes. The basic prerequisite for this is to be able to measure the loads occurring during the machining process in the form of mechanical deformations. Speckle photography is suitable for this in-process measurement task and is already used in a variety of ways for in-plane deformation measurements. The shortcoming of this fast and robust measurement technique based on image correlation techniques is that out-of-plane deformations in the direction of the measurement system cannot be detected and increases the measurement error of in-plane deformations. In this paper, we investigate a method that infers local out-of-plane motions of the workpiece surface from the decorrelation of speckle patterns and is thus able to reconstruct three-dimensional deformation fields. The implementation of the evaluation method enables a fast reconstruction of 3D deformation fields, so that the in-process capability remains given. First measurements in a deep rolling process show that dynamic deformations underneath the die can be captured and demonstrate the suitability of the speckle method for manufacturing process analysis.

Inverse algorithm for out-of-plane deformation in shearography

2021 ◽  
Vol 53 (1) ◽  
Author(s):  
Shuangle Wu ◽  
Fangyuan Sun ◽  
Haotian Xie ◽  
Qihan Zhao ◽  
Peizheng Yan ◽  
...  
Keyword(s):  
Plane Deformation ◽  
Inverse Algorithm ◽  
Out Of Plane

The Allocating Point Solution for the Out-of-Plane Stability of Arches with the Double Symmetry Axis Section

2010 ◽  
Vol 29-32 ◽  
pp. 1313-1316
Author(s):  
Yu Ji Chen
Keyword(s):  
Governing Equation ◽  
Spline Function ◽  
Symmetry Axis ◽  
Plane Deformation ◽  
Point Method ◽  
Out Of Plane ◽  
Point Solution ◽  
Double Symmetry ◽  
Paper Method

In order to study the buckling mechanics behaviour of the out-of-plane stability of arches with the double symmetry axis section, by mean of potential variational theories, considering the out-of-plane deformation of arches, the out-of-plane stability governing equation of arches was obtained. The problem was solved by the spline function allocating point method. An example was calculated with this paper method. It is shown by comparing the result of this paper with the others that the paper method is reliable and accurate.

Modeling and experimental investigation of out-of-plane deformation on mechanical performance of composites manufactured by ATL

2016 ◽  
Vol 36 (5) ◽  
pp. 347-359 ◽  
Author(s):  
Qiyi Chu ◽  
Yong Li ◽  
Jun Xiao ◽  
Dajun Huan ◽  
Xiaodong Chen
Keyword(s):  
Tensile Strength ◽  
Deformation Rate ◽  
Mechanical Performance ◽  
Plane Deformation ◽  
Experimental Results ◽  
Predicting Model ◽  
Fiber Waviness ◽  
Manufacturing Method ◽  
Four Point Bending ◽  
Out Of Plane

The change of mold normal curvature along the trajectory may result in out-of-plane waviness during the automated laying process, on which the layup speed and temperature would have an effect. A new parameter, deformation rate, was defined by combining the effect of mold curvature change rate and layup speed. A predicting model was proposed based on the fiber waviness and interlaminar sliding model to calculate the relationship between stiffness retention and the layup process parameters, including deformation rate and temperature. An experimental study on the effect of different deformation parameters on the tensile performance of composites was carried out based on a new manufacturing method of plated specimens with different levels of waviness by means of a four-point bending fixture. The experimental results showed that when the deformation temperature increases from 20℃ to 80℃, the tensile strength increases first and then decreases while the tensile module keeps increasing. While the deformation rate decreases from 0.40 to 0.04 mm−1/s, both tensile strength and module showed an increasing trend. The predicting model being validated by experimental results can be utilized to optimize the layup process parameter to satisfy the quality and efficiency requirements.

Sign in / Sign up

Export Citation Format

Share Document