A Simple Adapter for Soft Defect Localization Using OBIRCH

2007 ◽  
Author(s):  
Ted Kolasa
Keyword(s):  
Induced Resistance ◽  
Low Cost ◽  
Optical Beam ◽  
Significant Cost ◽  
Resistance Change ◽  
Design Considerations ◽  
Defect Localization

Abstract Equipment manufacturers have developed peripherals for their tools that add soft defect localization (SDL) capability to existing optical beam tools, in many cases providing excellent results. However, these upgrades add significant cost to the tool. This paper presents the design considerations for a simple adapter that was developed in house to add SDL capability to optical beam induced resistance change (OBIRCH) tool, including resolution of some unexpected problems. This solution represents a simple, low cost method to add SDL testing capability to the OBIRCH tool and can also be used in conjunction with OBIC and XIVA tools with little or no modification. An early example of the SDL results provided by this adapter is also presented.

Investigating carrier transport paths in organic nonvolatile bistable memory by optical beam induced resistance change

2011 ◽  
Vol 12 (10) ◽  
pp. 1632-1637 ◽  
Author(s):  
Heng-Tien Lin ◽  
Chang-Yu Lin ◽  
Zingway Pei ◽  
Jun-Rong Chen ◽  
Yi-Jen Chan ◽  
...  
Keyword(s):  
Induced Resistance ◽  
Carrier Transport ◽  
Optical Beam ◽  
Resistance Change

scholarly journals Preliminary Study on the Model of Thermal Laser Stimulation for Defect Localization in Integrated Circuits

2020 ◽  
Vol 10 (23) ◽  
pp. 8576
Author(s):  
Han Yang ◽  
Rui Chen ◽  
Jianwei Han ◽  
Yanan Liang ◽  
Yingqi Ma ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Induced Resistance ◽  
Seebeck Effect ◽  
Comprehensive Model ◽  
Induced Voltage ◽  
Efficient Technology ◽  
Resistance Change ◽  
Scanning Velocity ◽  
Laser Stimulation ◽  
Defect Localization

Thermal Laser Stimulation (TLS) is an efficient technology for integrated circuit defect localization in Failure Analysis (FA) laboratories. It contains Optical Beam-Induced Resistance Change (OBIRCH), Thermally-Induced Voltage Alteration (TIVA), and Seebeck Effect Imaging (SEI). These techniques respectively use the principle of laser-induced resistance change and the Seebeck effect. In this paper, a comprehensive model of TLS technology is proposed. Firstly, the model presents an analytical expression of the temperature variation in Integrated Circuits (IC) after laser irradiation, which quantificationally shows the positive correlation with laser power and the negative correlation with scanning velocity. Secondly, the model describes the opposite influence of laser-induced resistance change and the Seebeck effect in the device. Finally, the relationship between the current variation measured in the experiment and other parameters, especially the voltage bias, is well explained by the model. The comprehensive model provides theoretical guidance for the efficient and accurate defect localization of TLS technology.

Using Electrical Fault Isolation and Characterization to Improve the Effectiveness of Physical Fault Isolation Techniques for Analog Circuits

2017 ◽  
Author(s):  
Jim Douglass ◽  
Sohrab Pourmand
Keyword(s):  
Induced Resistance ◽  
Analog Circuits ◽  
Fault Isolation ◽  
Optical Beam ◽  
Resistance Change ◽  
Isolation Techniques ◽  
Isolation And Characterization ◽  
Lock In

Abstract This paper shows that by combining electrical fault isolation and characterization by microprobing with physical fault isolation techniques both what is wrong with the circuit and where the defect is located can be determined with less microprobing and more safety from electrical recovery. In the first example, the unit was powered up using the optical beam induced resistance change (OBIRCH) supply, and OBIRCH was performed to determine if there were OBIRCH site differences between the good part and the return. The second example uses a combination of electrical fault isolation and characterization with microprobing and the physical fault isolation tool of lock in thermography (LIT). With these two examples, it has been shown that the use of electrical fault isolation and microprobing can be used to enhance the physical fault isolation tools of OBIRCH and LIT.

High Resolution Localization Using Lock-in Based Electron Beam Methods

2017 ◽  
Author(s):  
Felix Rolf ◽  
Christian Hollerith ◽  
Christian Feuerbaum
Keyword(s):  
Electron Beam ◽  
High Resolution ◽  
Induced Resistance ◽  
High Efficiency ◽  
Optical Beam ◽  
Resistance Change ◽  
Root Cause ◽  
Special Challenge ◽  
Electron Beam Induced Current ◽  
Lock In

Abstract With decreasing transistor sizes accurate failure localization becomes more and more important in order to find the root cause of failures with high efficiency. Field returns are a special challenge, since there is usually only one sample for preparation. Hence, reliable high resolution localization is mandatory for a successful preparation. Optical beam induced resistance change (OBIRCH) is a powerful tool for localization but has resolution limitations due to the diameter of the optical beam. The tool can be further improved by the lock-in technique. In this paper we demonstrate that the lock-in technique can also be applied for electron beam localization methods like electron beam induced current (EBIC) / electron beam absorbed current (EBAC) and resistance change imaging (RCI) / electron beam induced resistance change (EBIRCH).

Sign in / Sign up

Export Citation Format

Share Document