scholarly journals A design concept of a device for measuring air flow resistance in vehicle filters

2020 ◽  
Author(s):  
Adrian Misztuk
Keyword(s):  
Flow Resistance ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Air Flow ◽  
Engine Performance ◽  
Internal Combustion ◽  
Design Concept ◽  
Compression Ignition Engine ◽  
Intake System ◽  
Air Intake

Internal combustion engines have to be supplied with adequate amounts of fuel and air. The required amount of fuel and air is determined by the engine controller to guarantee that the fuel reaching the cylinder is burned effectively and that the composition of exhaust gas meets standard requirements. The air supplied to an internal combustion engine has to be adequately filtered because impurities reaching the engine can accelerate the wear of engine components. The air intake system features a filtering partition which captures impurities and prevents them from reaching the engine. However, the filtering process decreases the rate at which cylinders are filled with fresh air, which can compromise engine performance. Therefore, effective solutions are needed to ensure that the flow of filtered air does not significantly decrease the volumetric efficiency of cylinders.  This study presents a design concept of a device for measuring pressure in the air intake system in front of and behind the filtering partition. The proposed device can be useful for measuring filter wear. A prototype of the proposed device was built and tested on several air filters. To eliminate throttle valve impacts, the device was tested in a compression ignition engine. The results of the conducted tests demonstrated that the device correctly measured air flow. The conducted measurements also revealed that the presence of impurities in the air filter induced differences in pressure in the air intake system in front of and behind the filtering partition. The maximum air flow resistance in a clogged filter could be even 100% higher than in a brand new filter. W niniejszej pracy przedstawiono koncepcję stanowiska umożliwiającego prowadzenie pomiarów ciśnienia panującego w kanale dolotowym silnika przed i za przegrodą filtracyjną powietrza, które mogą być przydatne przy określaniu stopnia jej zużycia. Dodatkowo zbudowano prototyp urządzenia i w celu weryfikacji poprawności jego działania przeprowadzono za jego pomocą badania przykładowych filtrów. Badania wykonano z użyciem silnika spalinowego o zapłonie samoczynnym. Wyniki pomiarów potwierdzają działanie urządzenia oraz obrazują zależności pomiędzy filtrami o różnym stopniu zużycia. Okazuje się, że maksymalny opór przepływu zużytego wkładu filtracyjnego może być nawet o ok. 100% większy niż w przypadku nowego wkładu filtracyjnego.

Computationally Efficient Simulation of Multi-Component Fuel Combustion Using a Sparse Analytical Jacobian Chemistry Solver and High-Dimensional Clustering

2013 ◽  
Author(s):  
Federico Perini ◽  
Anand Krishnasamy ◽  
Youngchul Ra ◽  
Rolf D. Reitz
Keyword(s):  
Reaction Mechanism ◽  
Chemical Kinetics ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Point Of View ◽  
High Dimensional ◽  
Computational Point ◽  
Fuel Surrogates

The need for more efficient and environmentally sustainable internal combustion engines is driving research towards the need to consider more realistic models for both fuel physics and chemistry. As far as compression ignition engines are concerned, phenomenological or lumped fuel models are unreliable to capture spray and combustion strategies outside of their validation domains — typically, high-pressure injection and high-temperature combustion. Furthermore, the development of variable-reactivity combustion strategies also creates the need to model comprehensively different hydrocarbon families even in single fuel surrogates. From the computational point of view, challenges to achieving practical simulation times arise from the dimensions of the reaction mechanism, that can be of hundreds species even if hydrocarbon families are lumped into representative compounds, and thus modeled with non-elementary, skeletal reaction pathways. In this case, it is also impossible to pursue further mechanism reductions to lower dimensions. CPU times for integrating chemical kinetics in internal combustion engine simulations ultimately scale with the number of cells in the grid, and with the cube number of species in the reaction mechanism. In the present work, two approaches to reduce the demands of engine simulations with detailed chemistry are presented. The first one addresses the demands due to the solution of the chemistry ODE system, and features the adoption of SpeedCHEM, a newly developed chemistry package that solves chemical kinetics using sparse analytical Jacobians. The second one aims to reduce the number of chemistry calculations by binning the CFD cells of the engine grid into a subset of clusters, where chemistry is solved and then mapped back to the original domain. In particular, a high-dimensional representation of the chemical state space is adopted for keeping track of the different fuel components, and a newly developed bounding-box-constrained k-means algorithm is used to subdivide the cells into reactively homogeneous clusters. The approaches have been tested on a number of simulations featuring multi-component diesel fuel surrogates, and different engine grids. The results show that significant CPU time reductions, of about one order of magnitude, can be achieved without loss of accuracy in both engine performance and emissions predictions, prompting for their applicability to more refined or full-sized engine grids.

scholarly journals Thermodynamic modeling of combustion process of the internal combustion engines – an overview

2019 ◽  
Vol 178 (3) ◽  
pp. 27-37 ◽  
Author(s):  
Denys STEPANENKO ◽  
Zbigniew KNEBA
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Engine Performance ◽  
Internal Combustion ◽  
Air Pollutant ◽  
Combustion Engines ◽  
Engine Simulation ◽  
Toxic Emissions ◽  
The Moment

The mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict in-cylinder pressure during the combustion, engine performance and environmental impact with high accuracy. The toxic emissions, which appears as a result of fuels combustion, are one of the main environmental problem and as a result the air pollutant regulations are increasingly stringent, what makes the investigation of the combustion process to be a relevant task.

scholarly journals Devising a model of the airflow with dust particles in the intake system of a vehicle’s internal combustion engine

2021 ◽  
Vol 2 (1 (110)) ◽  
pp. 61-69
Author(s):  
Olexii Saraiev ◽  
Alexander Khrulev
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Dust Particles ◽  
Two Phase ◽  
Air Filter ◽  
Intake System ◽  
Characteristic Particle ◽  
Pass Through

This paper considers the mechanism of malfunction of internal combustion engines that implies the accelerated local wear of parts in individual cylinders as a result of uneven distribution of dust particles that pass through the air filter in the intake system. In order to acquire quantitative data on the effect of the structure of the intake system on the redistribution of dust in engine cylinders, the two-phase flow of air with dust particles in the standard elements of the intake system was mathematically modeled. ANSYS software package was used to solve the problem. A simulation technique was devised in which the airflow was first calculated to determine the boundary conditions for dust, after which the flow of air with particles was calculated. The calculations were carried out in a range of air velocities of 5‒20 m/s in branching channels with diversion angles of 45°, 90°, and 135° for the most characteristic particle sizes of 5‒30 µm. It has been estimated that dust particles deviate from the air streamlines by inertia and can slip through the lateral drain the stronger the larger particle size, diversion angle, and velocity of air. The comparison of the simulation results with experimental data confirmed that in the intake system of some engines, due to uneven particle distribution, there is local abrasive wear in one or more cylinders, which can significantly reduce the resource. This paper shows the need to take into consideration the centrifugation and redistribution of dust in the intake systems during the design, modernization, expert studies to determine the causes of faults associated with faulty operating conditions, as well as to clarify the regulations for the maintenance of existing engines.

scholarly journals A Review of Comparative Study on The Effect of Hydroxyl Gas in Internal Combustion Engine (ICE) On Engine Performance and Exhaust Emission

2021 ◽  
Vol 87 (2) ◽  
pp. 1-16
Author(s):  
Amir Ridhuan ◽  
Shahrul Azmir Osman ◽  
Mas Fawzi ◽  
Ahmad Jais Alimin ◽  
Saliza Azlina Osman
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
Internal Combustion ◽  
Exhaust Emission ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Complete Combustion ◽  
Brake Power

This introductory study comes up with an innovative idea of using Hydroxyl gas as a fuel performance enhancer to reduce the natural sources and the overuse of fossil fuel resulting in increased pollution levels. Many researchers have used HHO gas to analyze gasoline and diesel in internal combustion engines. The main challenges of using HHO gas in engines have been identified as system complexity, safety, cost, and electrolysis efficiency. This article focuses on different performance reports and the emission characteristics of a compression ignition engine. As opposed to general diesel, this study found that using HHO gas improved brake power and torque. In all cases, an increase in braking thermal efficiency can be observed. This was due to the presence of hydrogen in HHO gas with higher calorific value than fossil fuels. At the same time, the fuel consumption unit of the engine was reduced, and the combined impact of hydrogen and oxygen helped to achieve complete combustion and improved the combustion capacity of the fuel when HHO gas was injected. The addition of HHO gas also improved the Brake Power (BP), Brake Torque (BT), Brake Specific Fuel Consumption (BSFC), and thermal efficiency while simultaneously reducing CO and HC formation. The rise in CO2 emissions represented the completion of combustion. Therefore, the usage of HHO gas in the Compression Ignition (CI) engine improved the engine performance and exhaust emissions.

scholarly journals A Review of Hydrogen Direct Injection for Internal Combustion Engines: Towards Carbon-Free Combustion

2019 ◽  
Vol 9 (22) ◽  
pp. 4842 ◽  
Author(s):  
Ho Lung Yip ◽  
Aleš Srna ◽  
Anthony Chun Yin Yuen ◽  
Sanghoon Kook ◽  
Robert A. Taylor ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Current Knowledge ◽  
Direct Injection ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Flammability Limits ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Engine Industry

A paradigm shift towards the utilization of carbon-neutral and low emission fuels is necessary in the internal combustion engine industry to fulfil the carbon emission goals and future legislation requirements in many countries. Hydrogen as an energy carrier and main fuel is a promising option due to its carbon-free content, wide flammability limits and fast flame speeds. For spark-ignited internal combustion engines, utilizing hydrogen direct injection has been proven to achieve high engine power output and efficiency with low emissions. This review provides an overview of the current development and understanding of hydrogen use in internal combustion engines that are usually spark ignited, under various engine operation modes and strategies. This paper then proceeds to outline the gaps in current knowledge, along with better potential strategies and technologies that could be adopted for hydrogen direct injection in the context of compression-ignition engine applications—topics that have not yet been extensively explored to date with hydrogen but have shown advantages with compressed natural gas.

Different Approaches for Determination of Internal Combustion Engines Performances

2016 ◽  
Vol 822 ◽  
pp. 169-174
Author(s):  
Alexandru Mihai Dima ◽  
Dragos Tutunea ◽  
Marin Bica
Keyword(s):  
Automotive Industry ◽  
World Economy ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Continue Development ◽  
The World

The automotive industry represents one of the most important segments of the world economy that has to be in a continue development. The latest procedures for determination of an internal combustion engine performance have a big acquisition cost and demand special conditions even if the tested engine has smaller dimensions. The present paper presents other accessible solutions for this matter.

scholarly journals Diagnosing of misfire events in compression-ignition engines with the help of vibroacoustic methods in the aspect of OBD system application in diesel locomotives

2008 ◽  
Vol 132 (1) ◽  
pp. 3-16
Author(s):  
Jerzy MERKISZ ◽  
Marek WALIGÓRSKI
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
High Reliability ◽  
Direct Injection ◽  
Combustion Process ◽  
Vibration Signal ◽  
Internal Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Railway Traction

The article concerns the possibilities of use of the method being able to assess of the combustion process and its lack in internal combustion engines of railway traction vehicles, that bases on the use of vibration signal parameters. The paper includes the results of research conducted on the engine test bench with a single cylinder research and compression-ignition engine with direct injection, and tests for the engine of a diesel locomotive in the exploitation condition. Possibility of the vibration signal estimators application to the assessment of a combustion process lack in an internal combustion engine and a high reliability of combustion process diagnostics basing on the above method have been proved.

scholarly journals Study of Unsteady Airflow in Muffler and Air Box Equivalent Geometries

2013 ◽  
Author(s):  
Nicolas-Ivan Hatat ◽  
François Lormier ◽  
David Chalet ◽  
Pascal Chesse
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Internal Combustion ◽  
Physical Models ◽  
One Dimensional ◽  
1D Modeling ◽  
Air Intake ◽  
And Performance

The Internal Combustion Engines (ICE) are inherently sources of the flow’s unsteadiness in the intake and exhaust ducts. Unsteady flow has a direct impact on the engine’s behavior and performance by influencing the filling and emptying of the cylinder. Air intake boxes as well as muffler geometries, which are very commonly used on the two-wheeled vehicles, have an impact on pressure levels and so, on air filling and performances levels. Thus, the purpose of this paper is to identify and analyze different typical geometries of these elements (air box and muffler) by comparing the test bench results with those obtained by 3D and 1D calculations. In this way, it is possible to establish a methodology for modeling the air box and muffler based on experimental tests and the development of 3D and then 1D model. In a beginning, studies consist in describing the geometry of the air box and muffler using a combination of tubes and simple volumes. During one-dimensional simulations, the gases properties in a volume must be calculated taking into account a method of filling and emptying. Under transient conditions, the pipe element is considered essentially as one-dimensional. The gas dynamic is described by a system of equations: the equations of continuity, momentum and energy. In the three-dimensional case, all tubes and volumes are meshed and solved using various physical models, equations and hypotheses that will be detailed subsequently. The study is performed on a shock tube bench. One of the main points is that this type of experimental test allows to test easily different pressure ratios, different geometries and to measure direct and inverse flow. In this way, the propagation of a shock wave is studied in our different geometries and is compared to the pressure signals obtained with 1D and 3D simulations. Once the 1D modeling is obtained, it must be validated in order to be applied in a simulation for Internal Combustion Engine. Validation will be done by direct comparison of results at each stage to ensure that the models and assumptions used in the calculations are correct.

Study of Combustion Anomalies of H2-ICE With External Mixture Formation

2006 ◽  
Author(s):  
Stephen A. Ciatti ◽  
Thomas Wallner ◽  
Henry Ng ◽  
William F. Stockhausen ◽  
Brad Boyer
Keyword(s):  
Internal Combustion Engines ◽  
Large Scale ◽  
High Efficiency ◽  
Combustion Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Engine Performance ◽  
Internal Combustion ◽  
Hydrogen Combustion ◽  
Mixture Formation

Although hydrogen is considered one of the most promising future energy carriers, there are several challenges to achieving a “hydrogen economy,” including finding a practical, efficient, cost-effective end-use device. Using hydrogen as a fuel for internal combustion engines is seen as a bridging technology toward a large-scale hydrogen infrastructure. To facilitate high-efficiency, high-power-density use of hydrogen with near-zero emissions in an internal combustion engine, detailed analysis of the hydrogen combustion process is necessary. This paper presents thermodynamic results regarding engine performance and emissions behavior during investigations performed on a single-cylinder research engine fueled by pressurized gaseous hydrogen. Avoiding combustion anomalies is one of the necessary steps to further improve the hydrogen engine power output at high-load operation while, at the same time, reducing fuel consumption and emissions during part-load operation. The overall target of the investigations is an improved combustion concept especially designed for hydrogen-engine-powered vehicles. Future activities include performing optical imaging of hydrogen combustion by using an endoscope. We will also investigate supercharged external mixture formation, as well as hydrogen direct-injection operation.

Sign in / Sign up

Export Citation Format

Share Document