scholarly journals Pengaruh Jumlah Sudu Terhadap Kinerja Turbin Savonius

2019 ◽  
Vol 6 (1) ◽  
pp. 64
Author(s):  
Jamal Jamal
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Research Method ◽  
Turbine Blades ◽  
Wind Speeds ◽  
Study Results ◽  
Torque Moment ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

Savonius wind turbines are wind turbines that canoperate at low wind speeds, this type of turbine is very suitable tobe used in several places in Indonesia. The research aims toimprove the performance of the Savonius wind turbine withvariations in the number of turbine blades as well as variations inthe velocity of wind speed. The research method wasexperimental where wind turbine testing was carried out withvariations in the number of turbine blades with number of 2, 3and 4 blades, other variations carried out were wind speed at 3.5;4,5; 5.5 and 6.5 m/s. The study results show that the 2-bladeturbine produces greater rotation, but the torque moment islower than the 3 and 4 blade turbines, this can be seen in the lowefficiency of the 2 blade turbine at low wind speeds with highloading. At 3.5 m / s wind turbines 2 blade turbines haveefficiency that tends to be the same as 3 and 4 blade turbines upto 0.5 N but at loads of 0.6 - 1.2 N 2 blade turbines have lowerefficiency, while at wind speeds of 4.5 - 6.5 m / s 2 blade turbineshave greater efficiency than turbines 3 and 4 blades up to a loadof 1.2 N but if the load is added then the efficiency of 2-bladeturbines can be smaller than efficiency 3 and 4-blade.

Effect of Slotted Angle on Savonius Wind Turbine Performance

2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Electrical Energy ◽  
Speed Ratio ◽  
Angle Variation ◽  
Wind Speeds ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.

scholarly journals Potential of Shrouded Micro Wind Turbine

2017 ◽  
Vol 7 (2 (S)) ◽  
pp. 340
Author(s):  
Kishor Sontakke ◽  
Samir Deshmukh ◽  
Sandip Patil
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Renewable Energy Sources ◽  
Turbine Blades ◽  
Weather Conditions ◽  
Power Coefficient ◽  
Solar Panels ◽  
Wind Speeds ◽  
Low Wind Speeds

The growing demand for electrical energy for industrial and domestic use, coupled with the limited amount of available fossil fuel reserves and its negative effects on the environment, have made it necessary to seek alternative and renewable energy sources. The use of renewable energy is promoted worldwide to be less dependent on conventional fuels and nuclear energy. Therefore research in the field is motivated to increase efficiency of renewable energy systems. This study aimed to study potential of micro wind turbine and velocity profile through shroud for low wind speeds. Although there is a greater inclination to use solar panels because of the local weather conditions, there are some practical implications that have place the use of solar panels in certain areas to an end. The biggest problem is panel stealing. Also, in some parts of the country the weather is more appropriate to apply wind turbines. Thus, this study paying attention on the design of a new concept to improve wind turbines to be appropriate for the low wind speeds in India. The concept involves the implementation of a concentrator and diffuser to a wind turbine, to increase the power coefficient. Although the wind turbine was not tested for starting speeds, the realization of the shroud should contribute to improved starting of the wind turbine at lower wind speeds. The configuration were not manufactured, but simulated with the use of a program to obtain the power production of the wind turbine over a range of wind speeds. These values were compared to measured results of an open wind turbine developed. The most important topic at hand when dealing with a shrouded wind turbine is to find out if the overall diameter or the blade diameter of the turbine should be the point of reference. As the wind turbine is situated in a shroud that has a larger diameter than the turbine blades, some researchers believe that the overall diameter should be used to calculate the efficiency. The benefits of shrouded wind turbines are discussed.

scholarly journals Pengaruh Jumlah Bilah dan Sudut Pasang terhadap Daya Turbin Angin Poros Vertikal Tipe H-Darrieus Termodifikasi sebagai Energi Alternatif Pembangkit Tenaga Listrik Skala Rumah Tangga

2019 ◽  
Vol 12 (2) ◽  
pp. 92
Author(s):  
Susilo Susilo ◽  
Bambang Widodo ◽  
Eva Magdalena Silalahi ◽  
Atmadi Priyono
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Output Power ◽  
Wind Turbines ◽  
Output Voltage ◽  
Turbine Rotor ◽  
Wind Speeds ◽  
Blade Shape ◽  
Low Wind Speeds ◽  
Wind Turbine Rotor

Bentuk sudu taper linier merupakan bentuk sudu yang paling optimal untuk kecepatan angin yang rendah. Jumlah sudu yang baik untuk kecepatan angin rendah berkisar antara 3-7 buah sudu, namun desain sudu dengan menggunakan airfoil dan profil pada sudut pasang sudu yang bagaimana memberikan daya keluaran dan tegangan keluaran yang optimal. Turbin angin didesain dengan 2 bilah dan 4 bilah dengan sudut pasang yang bisa diatur untuk mendapatkan perbedaan daya optimal masing-masing desain. Pengujian dilakukan di 3 area berbeda untuk mendapatkan gambaran geografis kondisi angin yang berbeda khususnya masalah kecepatan angin di ksiaran 2 m/s - 7 m/s. Pengujian dilakukan dengan luas penampang turbin angin (A) sebesar 3m2 Hasil penelitian menunjukkan bahwa nilai terbaik diperoleh pada kecepatan angin maksimal 4 m/s dan jumlah blade 4  sedangkan untuk nilai terkecil diperoleh pada kecepatan angin 3 m/s dan jumlah blade 2 yaitu. Untuk nilai TSR maksimal pada kecepatan maksimal 4 m/s terjadi pada jumlah blade 4, sedangkan untuk nilai terendah pada kecepatan angin 3 m/s dihasilkan pada jumlah blade 2. Melalui pengukuran berbasis teknologi smart monitoring system, dari penelitian diperoleh semakin tinggi kecepatan angin maka tegangan keluaran semakin tinggi. Semakin tinggi tegangan keluaran, semakin tinggi daya keluaran pada generator. Sudut pasang ? dan jumlah sudu mempengaruhi kecepatan putaran rotor turbin angin. Kecepatan putaran rotor turbin angin berelasi dengan tegangan keluaran generator. pada sudut pasang ? dan jumlah sudu 4, diperoleh daya keluaran yang sebesar 150 watt namun pada kecepatan angin 7 m/s daya turbin yang dihasilkan mencapai 600 watt. Dengan kondisi ini cukup memenuhi untuk alternatif cadangan listrik skala rumah tangga khusunya di pedesaan dan daerah terpencil (rural area). The linear taper blade shape is the most optimal blade shape for low wind speeds. The number of blades that are good for low wind speeds ranges from 3-7 blades, but the blade design uses an airfoil and profile on the blade mounting angle which is how to provide optimal output power and output voltage. Wind turbines are designed with 2 blades and 4 blades with adjustable tide angles to get the difference in the optimal power of each design. Tests were carried out in 3 different areas to obtain a geographical description of different wind conditions, especially the problem of wind speed in the range of 2 m / s - 7 m / s. Tests carried out with a cross section area of  wind turbines (A) of 3m2 The results showed that the best value was obtained at a maximum wind speed of 4 m / s and number 4 blade while the smallest value was obtained at wind speeds of 3 m / s and number 2 blades namely. For the maximum TSR value at a maximum speed of 4 m / s occurs in the number of 4 blades, while for the lowest value at 3 m / s wind speed is produced on the number of blades 2. From the research, the higher the wind speed, the higher the output voltage. The higher the output voltage, the higher the output power at the generator. The ? tide angle and number of blades affect the speed of the wind turbine rotor rotation. The rotational speed of the wind turbine rotor is related to the generator output voltage. at the tide angle ? and number of blades 4, the output power of 150 watts is obtained but with wind speed 7 m/s turbine power 600 watt achieved. With this condition, it is sufficient for alternative household electricity reserves, especially in rural and remote areas (rural areas).

scholarly journals Separated Pitch Control at Tip: Innovative Blade Design Explorations for Large MW Wind Turbine Blades

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Ranjeet Agarwala ◽  
Paul I. Ro
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Wind Turbine Blades ◽  
Pitch Control ◽  
Wind Speeds ◽  
Extreme Wind ◽  
Blade Tip ◽  
Low Wind Speeds ◽  
Extreme Wind Speeds

This paper focuses on the deployment and evaluation of a separated pitch control at blade tip (SePCaT) control strategy for large megawatt (MW) wind turbine blade and explorations of innovative blade designs as a result of such deployment. SePCaT configurations varied from five to thirty percent of the blade length in 5 percentage increments (SePCaT5, SePCaT10, SePCaT15, SePCaT20, SePCaT25, and SePCaT30) are evaluated by comparing them to aerodynamical responses of the traditional blade. For low, moderate, high, and extreme wind speed variations treated as 10, 20, 30, and 40 percent of reference wind speeds, rotor power abatement in region 3 of the wind speed power curve is realized by feathering full length blade by 6, 9, 12, and 14 degrees, respectively. Feathering SePCaT30, SePCaT25, SePCaT20, and SePCaT15 by 14, 16, 26, and 30 degrees, respectively, achieves the same power abatement results when compared to traditional blade at low wind speeds. Feathering SePCaT30, SePCaT25, and SePCaT20 by 18, 26, and 30 degrees on the other hand has the same effect at high wind speeds. SePCaT30 feathered to 26 and 30 degrees has the same abatement effects when compared to traditional blade at high and extreme wind speeds.

Analysis of a Concept for a Low Wind Speed Tolerant Axial Wind Turbine

2011 ◽  
Author(s):  
Ali A. Ameri ◽  
Majid Rashidi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Power Output ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Ambient Wind ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Low Wind Speeds

In this paper, the authors analyze a design for a wind tower intended for areas of low wind speeds. The wind tower consists of a combination of several rooftop size turbines arranged alongside a cylindrical structure that acts as a Wind Deflecting Structure (WDS). The WDS amplifies the effective wind speed thus allowing the turbine rotors to operate under lower ambient wind speeds. Analyses were performed using simple models as well as more sophisticated CFD methods employing Steady and Unsteady Reynolds Averaged Navier-Stokes methodology. The effect of the wind amplification was shown on a commercial small wind turbine power output map. Also, a wind turbine rotor flow was computed as operating alongside the WDS and compared to the computed operation of isolated turbines at equal effective and ambient wind velocities. The computational analyses of this work suggest that the power output of isolated rooftop wind turbines deployed at low to moderate wind speed may be matched by installing wind turbines alongside a cylindrical wind deflecting structure operating at lower wind speeds. Other benefits of the arrangement are also enumerated.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Pengaruh diameter dan jumlah sudu turbin angin savonius tipe L terhadap unjuk kerja yang dihasilkan

2020 ◽  
Vol 1 (2) ◽  
pp. 61-67
Author(s):  
Mohammad Rizqi Saputra ◽  
Nur Kholis ◽  
Mohammad Munib Rosadi
Keyword(s):  
Energy Source ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Mechanical Energy ◽  
Simulation Method ◽  
Wind Speeds ◽  
Turbine Efficiency ◽  
Analysis Technique ◽  
Low Wind Speeds ◽  
Wind Source

Abstract Wind is a renewable mechanical energy source that can be used as an energy source because the energy from the wind can be used to drive wind turbines. Savonius wind turbine type L is a tool to convert wind energy into electricity with a simple construction and can work with low wind speeds. The purpose of this study was to determine the effect of differences in diameter and number of blades on the power produced. The method used is a simulation method with an artificial wind source. With a wind speed of 8 m/s. The data analysis technique used is 2-way ANOVA using the SPSS application. Variations used are 20 cm and 40 cm in diameter and the number of blades 2 and 4 . The result is a wind turbine with a variation of 40 cm and 4 blades capable of producing the best output which produces 350.98 RPM voltage of 11.64 volts current of 0.144 amperes and power of 1,676 watts. As for BHP, torque, and turbine efficiency with a variation of 40 cm and 4 blades capable of producing the best output where the generated BHP is 3.352 watts, torque 0.091 N / m efficiency 2.17. For the results of calculations with SPSS wind turbines with a diameter variation of 40 cm and 4 blades, the biggest power is 1,744 watts and for BHP produces 3.3520 watts and the efficiency reaches 2.17%. Keyword : Diameter, number of blade, Performance Abstrak Angin adalah sumber energi mekanik yang bisa diperbaharui sehingga dapat dimanfaatkan sebagai sumber energi karena dapat digunakan untuk menggerakkan turbin angin. Turbin angin savonius tipe L merupakan alat untuk mengubah energi angin menjadi listrik dengan konstruksi yang sederhana dan dapat bekerja dengan kecepatan angin yang rendah. Tujuan penelitian ini untuk mengetahui pengaruh perbedaan diameter dan jumlah sudu terhadap unjuk kerja yang dihasilkan. Metode yang digunakan adalah metode simulasi dengan sumber angin buatan. Dengan kecepatan angin 8 m/s. Teknik analisis data yang digunakan adalah ANOVA 2 arah dengan menggunakan aplikasi SPSS. Variasi yang digunakan adalah diameter 20 cm dan 40 cm serta jumlah sudu 2 dan 4. Hasilnya turbin angin dengan variasi 40 cm dan 4 sudu mampu menghasilkan output terbaik yang dimana menghasilkan RPM 350,98 tegangan 11,64 volt arus 0,144 ampere dan daya 1,676 watt. Sedangkan untuk BHP, torsi, dan efisensi turbin dengan variasi 40 cm dan 4 sudu mampu menghasilkan output yang terbaik dimana BHP yang dihasilkan adalah 3,352 watt, torsi 0,091 N/m efisisensi 2,17. Untuk hasil perhitungan dengan SPSS turbin angin dengan variasi diameter 40 cm dan 4 sudu menghasilkan daya terbesar yakni 1,744 watt dan untuk BHP menghasilkan 3,3520 watt dan efisiensinya mencapai 2,17 % untuk torsi tertinggi dicapai turbin variasi 40 cm 2 sudu dengan torsi 0,116.   Kata kunci : diameter, jumlah sudu, unjuk kerja

Importance of Shear in Site Assessment of Wind Turbine Fatigue Loads

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
René M. M. Slot ◽  
Lasse Svenningsen ◽  
John D. Sørensen ◽  
Morten L. Thøgersen
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Reliability ◽  
Turbine Blades ◽  
Structural Response ◽  
Fatigue Loading ◽  
Worst Case ◽  
Shear Model ◽  
Wind Climate

Wind turbines are subjected to fatigue loading during their entire lifetime due to the fluctuating excitation from the wind. To predict the fatigue damage, the design standard IEC 61400-1 describes how to parametrize an on-site specific wind climate using the wind speed, turbulence, wind shear, air density, and flow inclination. In this framework, shear is currently modeled by its mean value, accounting for neither its natural variance nor its wind speed dependence. This very simple model may lead to inaccurate fatigue assessment of wind turbine components, whose structural response is nonlinear with shear. Here we show how this is the case for flapwise bending of blades, where the current shear model leads to inaccurate and in worst case nonconservative fatigue assessments. Based on an optimization study, we suggest modeling shear as a wind speed dependent 60% quantile. Using measurements from almost one hundred sites, we document that the suggested model leads to accurate and consistent fatigue assessments of wind turbine blades, without compromising other main components such as the tower and the shaft. The proposed shear model is intended as a replacement to the mean shear, and should be used alongside the current IEC models for the remaining climate parameters. Given the large number of investigated sites, a basis for evaluating the uncertainty related to using a simplified statistical wind climate is provided. This can be used in further research when assessing the structural reliability of wind turbines by a probabilistic or semiprobabilistic approach.

scholarly journals Analysis of the Patent of a Protective Cover for Vertical-Axis Wind Turbines (VAWTs): Simulations of Wind Flow

2020 ◽  
Vol 12 (18) ◽  
pp. 7818
Author(s):  
Jose Alberto Moleón Baca ◽  
Antonio Jesús Expósito González ◽  
Candido Gutiérrez Montes
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
High Speed ◽  
Experimental Tests ◽  
Weather Conditions ◽  
Vertical Axis ◽  
Good Alternative ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines

This paper presents a numerical and experimental analysis of the patent of a device to be used in vertical-axis wind turbines (VAWTs) under extreme wind conditions. The device consists of two hemispheres interconnected by a set of conveniently implemented variable section ducts through which the wind circulates to the blades. Furthermore, the design of the cross-section of the ducts allows the control of the wind speed inside the device. These ducts are intended to work as diffusers or nozzles, depending on the needs of the installation site. Simulations were performed for the case of high-speed external wind, for which the ducts act as diffusers to reduce wind speed and maintain a well-functioning internal turbine. Four different patent designs were analyzed, focusing on turbine performance and generated power. The results indicate that the patent allows the generation of electric power for a greater range of wind speeds than with a normal wind turbine. The results support that this patent may be a good alternative for wind power generation in geographic areas with extreme weather conditions or with maintained or strong gusty wind. Experimental tests were carried out on the movement of the blades using the available model. Finally, the power curve of the model of this wind turbine was obtained.

Design and Evaluation of a Rooftop Wind Turbine Rotor With Untwisted Blades

2013 ◽  
Author(s):  
Sayem Zafar ◽  
Mohamed Gadalla
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Low Cost ◽  
Turbine Blades ◽  
Angle Of Attack ◽  
Turbine Rotor ◽  
Wind Turbine Blades ◽  
Wind Speeds ◽  
Small Wind Turbines ◽  
Wind Turbine Rotor

A small horizontal axis wind turbine rotor was designed and tested with aerodynamically efficient, economical and easy to manufacture blades. Basic blade aerodynamic analysis was conducted using commercially available software. The blade span was constrained such that the complete wind turbine can be rooftop mountable with the envisioned wind turbine height of around 8 m. The blade was designed without any taper or twist to comply with the low cost and ease of manufacturing requirements. The aerodynamic analysis suggested laminar flow airfoils to be the most efficient airfoils for such use. Using NACA 63-418 airfoil, a rectangular blade geometry was selected with chord length of 0.27[m] and span of 1.52[m]. Glass reinforced plastic was used as the blade material for low cost and favorable strength to weight ratio with a skin thickness of 1[mm]. Because of the resultant velocity changes with respect to the blade span, while the blade is rotating, an optimal installed angle of attack was to be determined. The installed angle of attack was required to produce the highest possible rotation under usual wind speeds while start at relatively low speed. Tests were conducted at multiple wind speeds with blades mounted on free rotating shaft. The turbine was tested for three different installed angles and rotational speeds were recorded. The result showed increase in rotational speed with the increase in blade angle away from the free-stream velocity direction while the start-up speeds were found to be within close range of each other. At the optimal angle was found to be 22° from the plane of rotation. The results seem very promising for a low cost small wind turbine with no twist and taper in the blade. The tests established that non-twisted wind turbine blades, when used for rooftop small wind turbines, can generate useable electrical power for domestic consumption. It also established that, for small wind turbines, non-twisted, non-tapered blades provide an economical yet productive alternative to the existing complex wind turbine blades.

Sign in / Sign up

Export Citation Format

Share Document