scholarly journals Design of Piezoelectric Tile for Energy Harvesting: Experimental Approach

2021 ◽  
Vol 10 (2) ◽  
pp. 83-89
Author(s):  
Ehsan Maani Miandoab ◽  
Amir Hossein Jafari ◽  
Aref Valipour
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
External Force ◽  
Experimental Approach ◽  
Electrical Circuit ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Higher Power ◽  
Piezoelectric Elements

The generation of electricity by renewable energies is an important need of today's society. Piezoelectric energy harvesting is one of these useful technologies which can generate electricity by applying external force on piezoelectric material. This study illustrates more power generation from piezoelectric tile by changing the situation of piezo discs and connect to proportional electrical circuit. Two different designs of piezoelectric tile are presented by performing experimental analyses. The experimental results showed that placing piezoelectric elements in a bending position leads to higher power generation in comparison with traditional flat positioning, which was approximately 78 times far superior. It is also revealed that by design of an electrical circuit, the tile can be advantageous for lighting in crowded sidewalks with required lighting time. The results of this paper can be beneficial in the design and fabrication of these tiles for different applications.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

Piezoelectric Energy Harvesting Using a Clamped Circular Plate: Experimental Study

Aerospace ◽  
2003 ◽  
Author(s):  
Sunghwan Kim ◽  
William W. Clark ◽  
Qing-Ming Wang
Keyword(s):  
Energy Harvesting ◽  
Circular Plate ◽  
Energy Generation ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Plate Elements ◽  
Poling Direction ◽  
Electrical Devices ◽  
Piezoelectric Elements ◽  
Generation Theory

Energy harvesting using piezoelectric material is not a new concept, but its small generation capability has not been attractive for mass energy generation. For this reason, little research has been done on the topic. Recently, wearable computer concepts, as well as small portable electrical devices, are a few motivations that have reignited the study of piezoelectric energy harvesting. The theory behind cantilever type piezoelectric elements is well known, but the transverse moving circular plate elements, which can be used in pressure type energy generation is not yet fully developed. The power generation in a circular plate depends on several factors. Among them, the poling direction and the stress distribution is important as shown in previous research. Specifically, it has been shown theoretically that grouping electrodes and repoling some of the regrouped segments can lead to optimized energy harvesting in a clamped circular plate structure. This paper provides experimental validation of those results. In this paper, three circular plate piezoelectric energy generators (PEG), one unmodified and two different regrouped unimorph PEGs, were used to support the regrouped PEG energy generation theory. The experimental results of regrouped PEGs will be presented with an eye toward guidelines for design of a useful energy harvesting structure.

An Improved Tunable Piezoelectric Energy Harvesting Structure Based on d33 Mode Coupling

2015 ◽  
Vol 1092-1093 ◽  
pp. 136-140
Author(s):  
Yang Zhao ◽  
Kun Peng Wang ◽  
Ying Tai Li ◽  
Ming Jie Guan
Keyword(s):  
Energy Harvesting ◽  
Theoretical Analysis ◽  
Mode Coupling ◽  
Frequency Variation ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Piezoelectric Elements ◽  
Piezoelectric Harvester

This research proposes an improved tunable piezoelectric harvester structure which is constructed by a cantilever base beam and piezoelectric elements working in d33 mode. Our previous work on tunable piezoelectric harvester structure showed a frequency variation ratio of 3.17% with piezoelectric elements working in d31mode coupling. In this work, by changing the working mode of the piezoelectric elements from d31 to d33 mode, the frequency variation ratio was shown to be much higher. Theoretical analysis of the improved structure was investigated and verified with simulations. The results showed that the d33 mode coupling surpasses the d31 mode coupling with a frequency variation ratio of 29.74%.

scholarly journals Study of a Piezoelectric Energy Harvesting Floor Structure with Force Amplification Mechanism

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3516 ◽  
Author(s):  
He ◽  
Wang ◽  
Zhong ◽  
Guan
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Piezoelectric Energy Harvesting ◽  
Step Frequency ◽  
Peak Voltage ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam ◽  
Piezoelectric Elements ◽  
Floor Structure ◽  
Amplification Mechanism

This paper proposes a novel energy harvesting floor structure using piezoelectric elements for converting energy from human steps into electricity. The piezoelectric energy harvesting structure was constructed by a force amplification mechanism and a double-layer squeezing structure in which piezoelectric beams were deployed. The generated electrical voltage and output power were investigated in practical conditions under different strokes and step frequencies. The maximum peak-to-peak voltage was found to be 51.2 V at a stroke of 5 mm and a step frequency of 1.81 Hz. In addition, the corresponding output power for a single piezoelectric beam was tested to be 134.2 μW, demonstrating the potential of harvesting energy from the pedestrians for powering low-power electronic devices.

Demonstrating the effects of elastic support on power generation and storage capability of piezoelectric energy harvesting devices

2018 ◽  
Vol 30 (2) ◽  
pp. 323-332 ◽  
Author(s):  
Mohammad Reza Zamani Kouhpanji
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Elastic Properties ◽  
Elastic Support ◽  
Physical Parameters ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam ◽  
Energy Harvesting Devices ◽  
And Storage

This study represents effects of an elastic support on the power generation and storage capability of piezoelectric energy harvesting devices. The governing equations were derived and solved for a piezoelectric energy harvesting device made of elastic support, multilayer piezoelectric beam, and a proof mass at its free end. Furthermore, a Thevenin model for a rechargeable battery was considered for storage of the produced power of the piezoelectric energy harvesting device. Analyzing the time-domain and frequency-domain responses of the piezoelectric energy harvesting device on an elastic support shows that the elastic deformation of the support significantly reduces the power generation and storage capability of the device. It was also found that the power generation and storage capability of the piezoelectric energy harvesting device can be enhanced by choosing appropriate physical parameters of the piezoelectric beam even if the elastic properties of the support are poor relative to elastic properties of the piezoelectric beam. These results provide an insightful understanding for designing and material selection for the support in order to reach the highest possible power generation and storage capability for piezoelectric energy harvesting devices.

Circuit Development of Piezoelectric Energy Harvesting Device for Recharging Solid-State Batteries

2012 ◽  
Author(s):  
Yuejuan Li ◽  
Marvin H. Cheng ◽  
Ezzat G. Bakhoum
Keyword(s):  
Solid State ◽  
Energy Density ◽  
Energy Harvesting ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Sources ◽  
Piezoelectric Energy ◽  
Piezoelectric Elements ◽  
Volume Energy ◽  
Solid State Batteries

Piezoelectric devices have been widely used as a means of transforming ambient vibrations into electrical energy that can be stored and used to power other devices. This type of power generation devices can provide a convenient alternative to traditional power sources used to operate certain types of sensors/actuators, MEMS devices, and microprocessor units. However, the amount of energy produced by these devices is in many cases far too small to directly power an electrical device. Therefore, much of the research into power harvesting has focused on methods of accumulating the energy until a sufficient amount is present, allowing the intended electronics to be powered. Due to the tiny amount of harvestable power from a single device, it is critical to collect vibration energy efficiently. Many research groups have developed various methods to operate the harvesting devices at their resonant frequencies for maximal amount of energy. Different techniques of conversion circuits are also investigated for efficient transformation from mechanical vibration to electrical energy. However, efforts have not been made to the analysis of array configuration of energy harvesting elements. Poor combination of piezoelectric elements, such as phase difference, cannot guarantee the increasing amount of harvested energy. To realize a piezoelectric energy-harvesting device with higher volume energy density, the energy conversion efficiencies of different array configurations were investigated. In the present study, various combinations of piezoelectric elements were analyzed to achieve higher volume energy density. A charging circuit for solid-state batteries with planned energy harvesting strategy was also proposed. With the planned harvesting strategy, the required charging time can be estimated. Thus, the applicable applications can be clearly identified. In this paper, optimal combination of piezoelectric cantilevers and different modes of charging methods were investigated. The results provide a means of choosing the piezoelectric device to be used and estimate the amount of time required to recharge a specific capacity solid-state battery.

Piezoelectric Energy Harvesting Improvement with Complex Conjugate Impedance Matching

2008 ◽  
Vol 20 (5) ◽  
pp. 597-608 ◽  
Author(s):  
J. Brufau-Penella ◽  
M. Puig-Vidal
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Transducer ◽  
Impedance Matching ◽  
Resonant Mode ◽  
Electrical Circuit ◽  
Impedance Match ◽  
Complex Conjugate ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Harvesting Systems

One way to enhance the efficiency of energy harvesting systems is complex conjugate impedance matching of its electrical impedance. In Piezoelectric energy Harvesting systems the match is done to increment the energy flows from a vibration energy source to an energy storage electrical circuit. In this article, we compare the power generated using the modulus impedance matching with the power generated using the complex conjugate impedance matching. We present the power ratio between both types of matching methods. The novelty of this article consists of a piezoelectric transducer completely adapted with a complex conjugate impedance match. The theory developed is validated on a commercial piezoelectric transducer QP40w from Midé Technology. The transducer model is first identified by means of a system identification step based on a novel two-port Lumped-Electromechanical Model. The QP40w is complex conjugate matched at its fourth resonant mode increasing the generated power by up to 20% more compared with the modulus match.

Sign in / Sign up

Export Citation Format

Share Document