scholarly journals A Numerical Comparison between Spiral Transverse RC and CFST Columns under Loads of Varying Eccentricities

2019 ◽  
Author(s):  
Mojtaba Labibzadeh ◽  
Reza Jamalpour ◽  
Deng H. Jing ◽  
Amin Khajehdezfuly
Keyword(s):  
Carrying Capacity ◽  
Numerical Models ◽  
Steel Tube ◽  
Numerical Comparison ◽  
Load Carrying Capacity ◽  
Initial Stiffness ◽  
Concrete Core ◽  
Load Carrying ◽  
Concrete Damage ◽  
Cfst Columns

This paper is the first to present the results of a numerical comparison between the performances of two newly developed concrete columns namely: multi-tied spiral transverse reinforced (MTSTR) column and concrete-filled steel tube (CFST) column under eccentric compressive loads. The behavior of MTSTR columns under eccentric loads has not been studied until today and also this behavior is not compared to that of the CFST columns. The numerical models of these columns were constructed using the nonlinear finite element method and validated against the previously published experimental data in the literature. Concrete damage plasticity model and elastic-perfect plastic model were used to simulate the behavior of concrete core and steel of the columns, respectively. This provides the capability of modeling of the nonlinear large deformations of the columns. The obtained results show that the MTSTR columns can provide greater load carrying capacity, ductility, and energy absorption with slightly lower initial stiffness than the CFST columns under the same eccentricities. For instance, the load-carrying capacity of MTSTR column is 18 percent greater than that of the CFST column when the load eccentricity is 100 mm. In case of 100 mm eccentricity, the ductility of the improved version of the MTSTR column proposed in this study is 30 percent greater than CFST one.

scholarly journals Experimental Behaviour of Steel Tubular Columns for Varying in Filled Concrete

2017 ◽  
Vol 63 (4) ◽  
pp. 149-160 ◽  
Author(s):  
P. Sangeetha ◽  
R. Senthil
Keyword(s):  
Carrying Capacity ◽  
Slenderness Ratio ◽  
Steel Tube ◽  
Load Carrying Capacity ◽  
Concrete Core ◽  
Composite Action ◽  
Tubular Columns ◽  
Load Carrying ◽  
Cfst Columns ◽  
Quarry Dust

AbstractThis paper investigates the behaviour of axially-loaded tubular columns filled with M20 grade concrete and partially replaced concrete. The parameters varying in the study are slenderness ratio (13.27, 16.58 & 19.9), and normal M20 grade concrete, partially replaced quarry dust and concrete debris. The effects of the various concrete mixes and composite action between the steel tube and the concrete core are studied and a graph visualizing the differences between the load carrying capacity and the axial deflection is plotted. Some of the performance indices like the Ductility Index (DI), Concrete Contribution Ratio (CCR), Confinement Index (θ) and Strength Index (SI) are also evaluated and compared amongst the CFST columns. From the results it has been noted that an increase in the L/D ratio decrease the behaviour of the composite columns irrespective of the in filled materials. The composite action was achieved in the CFST columns filled with partially replaced quarry dust and concrete debris when compared with hollow steel columns. The load carrying capacity of the CFST column increases by 32 % compared with the hollow tubular columns.

scholarly journals Nonlinear Analysis of Circular Concrete Filled Steel Tube Columns under Axial Loading

2019 ◽  
Vol 8 (12) ◽  
pp. 688-692
Keyword(s):  
Carrying Capacity ◽  
Axial Loading ◽  
Steel Tube ◽  
Load Carrying Capacity ◽  
Building Structures ◽  
Inelastic Behavior ◽  
Concrete Filled Steel Tube ◽  
Load Carrying ◽  
Cfst Columns ◽  
Von Mises

Concrete filled steel tube (CFST) columns are composite member mainly consists of concrete infilled in steel tube. In current construction industry, CFST columns are preferred to provide lateral resistance in both unbraced and braced building structures. In this paper, finite element studies were carried out on concrete filled steel tube columns under an axial composite loading by using ABAQUS/CAE. The inelastic behavior of concrete and steel tube was defined to the model by using concrete damaged plasticity model (CDP) and Johnson-cook model respectively which is available in ABAQUS/CAE. The diameters of columns were considered as 100 mm, 125 mm and 150 mm, whereas the length of columns was kept constant, i.e. 600 mm for all models. The thickness of steel tube was considered as 4 mm and 5 mm for all diameters of columns. The concrete infilled of grade M30 was used in this study. The simulations were carried out against composite loading to study the response of CFST columns in terms of load carrying capacity, displacement and von-mises stresses. The mesh conversion study was also carried out to obtain the best size of mesh corresponding to the experimental load carrying capacity of CFST columns

scholarly journals Experimental Research on AFRP Reinforced Recycled Steel Tube Columns Subjected to Axial Compression

2017 ◽  
Vol 26 (6) ◽  
pp. 096369351702600
Author(s):  
Min Hou ◽  
Jiangfeng Dong ◽  
Lang Li ◽  
Shucheng Yuan ◽  
Qingyuan Wang
Keyword(s):  
Carrying Capacity ◽  
Failure Modes ◽  
Basalt Fiber ◽  
Steel Tube ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
The One ◽  
Effective Use

In order to make an effective use of the recycled aggregate concrete (RAC), a total of six steel tube RAC columns and six basalt fiber (BF) reinforced RAC columns, including six columns that were externally strengthened with aramid fiber reinforced polymer (AFRP) sheets, were fabricated and tested. This were to provide a strengthening solution to upgrade the load carrying capacity, ductility and rigidity of the RAC filled steel tube columns. Besides, the recycled coarse aggregate (RCA) replacement ratios for production of RAC was analyzed. The results show that the load carrying capacity and ultimate displacements of the RAC filled ST columns could be improved greatly by adding of basalt fiber, especially for the specimens with 50% and 100% RCA replacement ratio. The similar result was also found for the specimens strengthened with AFRP reinforcement, along with the stiffness of the columns were enhanced obviously. Moreover, the highest improving on the load carrying capacity, stiffness and ultimate displacement was found in the specimens both reinforced by adding of BF and strengthening of AFRP. However, the failure modes of the specimens with BF reinforced RAC gave a higher deformability than the one with AFRP strengthening arrangement.

Experimental Investigation on Composite Circular Steel Columns - Taguchi’s Approach

2011 ◽  
Vol 105-107 ◽  
pp. 1742-1750
Author(s):  
N. S. Kumar ◽  
Sameera Simha T.P.
Keyword(s):  
Linear Regression ◽  
Carrying Capacity ◽  
Orthogonal Array ◽  
Regression Models ◽  
Ultimate Load ◽  
Steel Tube ◽  
Load Carrying Capacity ◽  
Taguchi’S Method ◽  
Steel Tubes ◽  
Load Carrying

Composite circular steel tubes- with and without epoxy infill for three different grades of concrete are tested for ultimate load capacity and axial shortening , under axial monotonic loading for compression. Steel tubes are compared for different lengths, cross sections and thickness. Specimens were tested separately after adopting Taguchi’s L9 (Latin Squares) Orthogonal array in order to save the initial experimental cost on number of specimens and experimental duration. DOE (Design of Experiment) approach was adopted. Results were generated using Taguchi’s method-a new technique to get mean effects plot. Analysis was carried out using ANOVA (Analysis of Variance) technique with the assistance of Mini Tab v15- a statistical soft tool. Results were verified after conducting preliminary nine combination experiments as per L9 orthogonal array and linear regression models were developed. Comparison for predicted and experimental output is obtained from linear regression plots. To know the implications of different factors on circular composite columns with and without epoxy, surface contours were also generated. From this research study it is concluded that ,Regression models which were developed with minimum number of experiments based on Taguchi’s method predicted the axial load carrying capacity very well and reasonably well for at ultimate point. Cross sectional area of steel tube has most significant effect on ultimate load carrying capacity. Also it is observed that, as length of steel tube increased- load carrying capacity decreased.

Analysis of the Load-Carrying Capability of the Casing Plug Joint of Steel Tube Structures Considering the Contact Effect

2008 ◽  
Vol 33-37 ◽  
pp. 321-326 ◽  
Author(s):  
Xiu Gen Jiang ◽  
Yang Yang ◽  
Feng Jie Zhang ◽  
Jin San Ju ◽  
Xiao Chuan You
Keyword(s):  
Finite Element ◽  
Carrying Capacity ◽  
Element Model ◽  
Steel Tube ◽  
Nonlinear Finite Element ◽  
Tube Length ◽  
Load Carrying Capacity ◽  
Ansys Software ◽  
Load Carrying ◽  
Nonlinear Finite Element Model

Nonlinear finite element model analysis of the casing plug joints of steel tubular has been realized by ANSYS software. The law of load-carrying capability and stiffness of joint are separately gained by changing the ratio of length and diameter (R/L) and the ratio of the casing length and the main tube length (l/L). The influence of the casing thickness on the load-carrying capability and stiffness are also discussed. The results indicated that the load-carrying capability and stiffness of the joints both increase with the ratio(R/L) increment and the ratio of the casing length and main tube length (l/L). When the main tube thickness is equal to casing thickness, the load-carrying capacity of joints achieves the most.

Load Carrying Capacity Calculation of Shear Wall with Concrete Filled Steel Tube Columns and Concealed Trusses

2013 ◽  
Vol 438-439 ◽  
pp. 706-710
Author(s):  
Ya Bin Yang ◽  
Wan Lin Cao
Keyword(s):  
Seismic Performance ◽  
Carrying Capacity ◽  
Shear Wall ◽  
Steel Tube ◽  
Load Carrying Capacity ◽  
Concrete Filled Steel Tube ◽  
Hysteretic Property ◽  
Load Carrying ◽  
Capacity Calculation ◽  
Steel Trusses

Shear wall with concrete filled steel tube columns and concealed trusses is a new kind of shear wall. In order to further the seismic performance of the new shear wall, experiment was carried on three 1/5 scale models, which included one traditional RC shear wall, one shear wall with concrete filled steel tube columns, one shear wall with concrete filled steel tube columns and concealed trusses. Based on the experimental study, load-carrying capacity and hysteretic property of each model were analyzed. The study show that the seismic performance of shear wall with concrete filled round steel tube columns and concealed steel trusses has high bearing capacity and good hysteretic property. Load carrying capacity calculation of shear wall with concrete filled steel tube columns and concealed steel trusses were carried out, the calculate results were in good agreement with the measured results.

Experiment Study on Influence of Initial Stress in Concrete Filled Steel Tubular Latticed Columns under Axial Load

2014 ◽  
Vol 518 ◽  
pp. 170-177
Author(s):  
Fu Yun Huang ◽  
Guan Yu ◽  
Bao Chun Chen ◽  
Jian Zhong Li
Keyword(s):  
Initial Stress ◽  
Carrying Capacity ◽  
Axial Load ◽  
Ultimate Load ◽  
Load Carrying Capacity ◽  
Experiment Study ◽  
Load Carrying ◽  
Plastic Phase ◽  
Cfst Columns ◽  
Ultimate Load Carrying Capacity

The testing of concrete filled steel tubular (CFST) latticed columns with initial stress had been conducted under axial load. The set-ups subjected to initial stress, the curves of load to deformation as well as the hooping effect were analyzed. The trial results indicate that the CFST columns with initial stress have smaller of combined stiffness and ultimate load-carrying capacity as compared with CFST columns without initial stress. Furthermore, the presence of initial stress will advance the coming of plastic phase, and contemporary, put off the appearances of hooping effect so that it cannot be sufficient exerted, which decrease the ultimate load-carrying capacity at all. Nevertheless, the mechanical behaviour of lacing tubes does not vary with the initial stress and all the lace tubes are stayed in the elastic phase during the testing.

scholarly journals Calculation Method for Load-Carrying Capacity of Circular Reinforced Con

2021 ◽  
Vol 353 ◽  
pp. 01013
Author(s):  
Tingwei Wang
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Steel Tube ◽  
Experimental Result ◽  
Load Carrying Capacity ◽  
Model Method ◽  
Concrete Members ◽  
Load Carrying

Finite element method and fiber model method were used to calculate the load-carrying capacity of the specimens. Based on the experimental and theoretical analysis, simplified calculation method of the load-carrying capacity for this kind of member is proposed. It indicates that finite element method result is relatively small, fiber model method result accords well with the experimental result. Circular reinforced concrete members covered with steel tube presents both the characteristics of reinforced concrete and concrete filled steel tube member, showing higher load-carrying capacity and greater deformability. The load-carrying capacity of circular reinforced concrete members covered with steel tube can be calculated by the means of the method of reinforced concrete member with confined concrete. The result predicted by the simplified method is in good agreement with the experimental result.

scholarly journals Load-carrying capacity of welded K-type joints inside floor truss systems

2019 ◽  
Vol 52 (1) ◽  
pp. 38-52
Author(s):  
Pooya Saremi ◽  
Wei Lu ◽  
Jari Puttonen ◽  
Dan Pada ◽  
Jyrki Kesti
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Carrying Capacity ◽  
Numerical Models ◽  
High Load ◽  
Load Carrying Capacity ◽  
Finite Element Analyses ◽  
Load Bearing Capacity ◽  
Load Carrying ◽  
Joint Behaviour

The load-carrying capacity of a K-type joint inside a floor truss is studied both experimentally and numerically. The joint tested is a scaled-down, isolated joint. The tubular braces, plate chord, and division plate are made of SSAB Domex steel. Comparison of load displacement curves received by finite element analyses with curves obtained from tests confirms that numerical models describe joint behaviour reasonable. The paper demonstrates that joints with high load-bearing capacity can be investigated experimentally by scaling the dimensions of the joint down when testing devices can affect the required capacity of the joint. The results presented can also be used for optimizing failure mechanism of similar joints in practice.

Performance of the Casing-Plug Joints of Square Steel Tube Structures

2011 ◽  
Vol 462-463 ◽  
pp. 265-270
Author(s):  
Xiu Gen Jiang ◽  
Ning Xu ◽  
Xu Dong Shi ◽  
Yu Huan Wu ◽  
Xing Hua Chen ◽  
...  
Keyword(s):  
Cross Section ◽  
Carrying Capacity ◽  
Failure Modes ◽  
Influence Factors ◽  
Steel Tube ◽  
Load Carrying Capacity ◽  
Ansys Software ◽  
Tube Cross Section ◽  
Load Carrying ◽  
Square Steel Tube

The performance of the casing-plug joint, including load carrying capacity, stiffness, failure modes, and its influence factors of the casing tubes set inside and outside of the main tubes are analyzed by simulating square steel tube casing-plug joints structures with ANSYS software in this paper. The formulas of the optimum l/L for the joints with the size of the main tube cross-section 200mm× 200mm are given in this paper.

Sign in / Sign up

Export Citation Format

Share Document