scholarly journals Effect of Deformation Conditions on Mechanical Properties of Zr-based Metallic Glasses

2020 ◽  
Vol 2 (2) ◽  
Author(s):  
Zhenxiang ZHAO ◽  
Chunyan LI ◽  
Fuping ZHU ◽  
Xinling LI ◽  
Shengzhong KOU
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Aspect Ratio ◽  
Plastic Strain ◽  
Strain Rate ◽  
Fracture Strength ◽  
Metallic Glasses ◽  
Room Temperature

In this paper, the effects of different strain rate(1×10-5 s-1, 5×10-5 s-1, 1×10-4 s-1, 5×10-4 s-1, 1×10-3 s-1) and aspect ratio(1:1, 1.5:1, 2:1, 2.5:1, 3:1) on mechanical properties of Zr-based metallic glasses at room temperature were investigated. The results indicate that as the strain rate increases, the plastic strain and compressive strength of the specimens gradually decrease. The specimen with the strain rate of 1×10-5 s-1 exhibits the higher plastic strain of 10.25 %, compressive strength of 2002 MPa and fracture strength of 1999 MPa. In addition, accompanied with the increase in aspect ratio, the plastic strain of the specimens declines from 25.42 % to 1.97 %, meanwhile, the compressive strength and fracture strength of the specimens also present declining trend.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

scholarly journals Characterization and Comparison of Geopolymer Synthesized Using Metakaolin Bangka and Metastar as Precursors

2018 ◽  
Vol 67 ◽  
pp. 03022
Author(s):  
Sotya Astutiningsih ◽  
Dicky Tambun ◽  
Ahmad Zakiyuddin
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Room Temperature ◽  
Mechanical Test ◽  
Strength Test ◽  
Thermal Activity ◽  
Metallurgical Properties ◽  
Metakaolin Geopolymer ◽  
Kaolin Deposit

Various aluminosilicate material have been used as precursor for geopolymer. Geopolymer gets its strength from the polycondensation of silicate and alumina. Metakaolin, calcinated kaolin, is pozzolan with the highest alumina and silicate purity. Indonesia, especially Bangka Island, has a large amount of kaolin deposit that being sold at low price. This price could be increased ten times when being sold as metakaolin. This study aimed to compare mechanical and metallurgical properties of commercial metakaolin and Bangka kaolin which calcinated at 700°C. Both metakaolins reacted with NaOH and waterglass as the activator followed by curing at room temperature for 7, 14 and 28 days and elevated temperature of 60°C for 4, 12 and 24 hours. Mechanical properties will be examined by compressive strength and flexural strength test, while the metallurgical properties will be evaluated with SEM, and TAM. The results of the mechanical test will be used to determine which geopolymer will perform well with the microstructure and thermal activity to support the finding. These attempts will be done in order to improve the properties of Bangka metakaolin geopolymer superior to commercial metakaolin.

scholarly journals Low-temperature degradation resistance and plastic deformation of ATZ ceramics stabilized by CaO

2021 ◽  
Vol 2103 (1) ◽  
pp. 012075
Author(s):  
AA Dmitrievskiy ◽  
DG Zhigacheva ◽  
VM Vasyukov ◽  
PN Ovchinnikov
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Plastic Deformation ◽  
Compressive Strength ◽  
Phase Composition ◽  
Low Temperature ◽  
Uniaxial Compression ◽  
Calcium Oxide ◽  
Tetragonal Phase ◽  
Room Temperature

Abstract In this work, the phase composition (relative fractions of monoclinic m-ZrO2, tetragonal t-ZrO2, and cubic c-ZrO2 phases) and mechanical properties (hardness, fracture toughness, compressive strength) of alumina toughened zirconia (ATZ) ceramics, with an addition of silica were investigated. Calcium oxide was used as a stabilizer for the zirconia tetragonal phase. It was shown that CaO-ATZ+SiO2 ceramics demonstrate increased resistance to low-temperature degradation. The plasticity signs at room temperature were found due to the SiO2 addition to CaO-ATZ ceramics. A yield plateau appears in the uniaxial compression diagram at 5 mol. % SiO2 concentration. It is hypothesized that discovered plasticity is due to the increased t→m transformability.

scholarly journals The Prospects for Mechanical Ratcheting of Bulk Metallic Glasses

2003 ◽  
Vol 806 ◽  
Author(s):  
Wendelin J. Wright ◽  
R. H. Dauskardt ◽  
W. D. Nix
Keyword(s):  
Plastic Strain ◽  
Metallic Glasses ◽  
Room Temperature ◽  
Tensile Axis ◽  
Uniaxial Stress ◽  
Temperature Deformation ◽  
Steel Alloys ◽  
Cyclic Torsion ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

ABSTRACTThe major mechanical shortcoming of metallic glasses is their limited ductility at room temperature. Monolithic metallic glasses sustain only a few percent plastic strain when subjected to uniaxial compression and essentially no plastic strain under tension. Here we describe a room temperature deformation process that may have the potential to overcome the limited ductility of monolithic metallic glasses and achieve large plastic strains. By subjecting a metallic glass sample to cyclic torsion, the glass is brought to the yield surface; the superposition of a small uniaxial stress (much smaller than the yield stress) should then produce increments in plastic strain along the tensile axis. This accumulation of strain during cyclic loading, commonly known as ratcheting, has been extensively investigated in stainless and carbon steel alloys, but has not been previously studied in metallic glasses. We have successfully demonstrated the application of this ratcheting technique of cyclic torsion with superimposed tension for polycrystalline Ti–6Al–4V. Our stability analyses indicate that the plastic deformation of materials exhibiting elastic–perfectly plastic constitutive behavior such as metallic glasses should be stable under cyclic torsion, however, results obtained thus far are inconclusive.

An Assessment of the Method Used to Determine Activation Parameters in L12 Alloys

1998 ◽  
Vol 552 ◽  
Author(s):  
B. Matterstock ◽  
G. Saada ◽  
J. Bonneville ◽  
J. L Martin
Keyword(s):  
Mechanical Properties ◽  
Theoretical Analysis ◽  
Plastic Strain ◽  
Strain Rate ◽  
Characteristic Time ◽  
Constant Strain Rate ◽  
Activation Parameters ◽  
Plastic Strain Rate ◽  
Clear Indication ◽  
Load Relaxation

ABSTRACTThe characterisation of dislocation mechanisms in connection with macroscopic mechanical properties are usually performed through transient tests, such as strain-rate jumps, load relaxations or creep experiments. The present paper includes a careful and complete theoretical analysis of the relaxation and the creep kinetics. We experimentally show that the plastic strain-rate is continuous at the transition between constant strain-rate conditions and both load relaxation and creep test. The product of the plastic strain-rate at the onset of the transient test () with the characteristic time (tk) of the transient is found to be independent of , as theoretically expected. This is a clear indication that the assumptions underlying the theoretical analysis are relevant.

Influence of High Temperatures on the Mechanical Properties of Wood Bio-Concretes

2022 ◽  
Author(s):  
Amanda Lorena Dantas Aguiar ◽  
M’hamed Yassin Rajiv da Gloria ◽  
Romildo Dias Toledo Filho
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperatures ◽  
Room Temperature ◽  
Plant Biomass ◽  
Compression Tests ◽  
Wood Degradation ◽  
Cementitious Matrix ◽  
Wood Shavings ◽  
Temperature Reference

The use of wood wastes in the production of bio-concrete shows high potential for the development of sustainable civil construction, since this material, in addition to having low density, increases the energy efficiency of buildings in terms of thermal insulation. However, a concern arising from the production of bio-concretes with high amounts of plant biomass is how this material behaves when subjected to high temperatures. Therefore, this work aims to evaluate the influence of high temperatures on the mechanical properties of wood bio-concretes. The mixtures were produced with wood shavings volumetric fractions of 40, 50 and 60% and cementitious matrix composed of a combination of cement, fly ash and metakaolin. Uniaxial compression tests and scanning electron microscopy (SEM) were performed, with bio-concrete at age of 28 days, at room temperature (reference) and after exposure to temperatures of 100, 150, 200 and 250 °C. The density and compressive strength of the bio-concrete gradually decreased with increasing biomass content. Up to 200 °C, reductions in strength and densities less than 19% and 13%, respectively, were observed. At 250 °C, reductions of compressive strength reached 87%. Analysis performed by SEM showed an increase in the number of cracks in the wood-cementitious matrix interface and wood degradation by increasing the temperature.

Effect of aspect ratio on the mechanical properties of metallic glasses

2014 ◽  
Vol 93 ◽  
pp. 36-39 ◽  
Author(s):  
Z.D. Sha ◽  
L.C. He ◽  
S. Xu ◽  
Q.X. Pei ◽  
Z.S. Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Metallic Glasses
Sign in / Sign up

Export Citation Format

Share Document