SPECIALTY NATURAL RUBBER LATEX FOAM: FOAMABILITY STUDY AND FABRICATION PROCESS

ABSTRACT Specialty natural rubber (SpNR) latex, namely, deproteinized natural rubber (DPNR) latex and epoxidized natural rubber (ENR) latex, has been produced to meet specific product's requirements. However, SpNR is normally used in the form of block rubber to manufacture dry rubber products such as tires and automotive parts. The applications of SpNR latex into latex foam products will be diversified. Findings indicate that foamability of SpNR latex is lower compared to normal latex (LATZ) but shows longer stability time after foamed. Findings also indicate that foam collapse and foam coagulate are two main challenges in the fabrication process of SpNR latex foam. Despite these challenges, SpNR latex foam can be fabricated at different density levels. During the foaming process, additional foaming agent is required to fabricate a SpNR latex foam, which is different from fabricating a normal NR latex foam, especially at low latex foam density. Consequently, a higher level of sodium silicofluoride, used as the gelling agent, is required to set the cell structure of the foam. Findings also indicate that foam density influenced the gelling time and volume shrinkage of the SpNR latex foam. An ideal compounding, foaming, and gelling formulation to fabricate SpNR latex foam via Dunlop batch foaming process has been developed. Morphological study showed that all latex foams are open-cell structure, with lower density foam exhibiting higher porosity and mean pore size. Comparison on hysteresis behavior between DPNR and ENR latex foam indicated that ENR latex foam exhibits higher hysteresis loss ratio compared to DPNR latex foam.

Dynamic generation of aqueous foams and fiber foams in a mixing tank

Mixing tanks are employed in paper and pulp industries to generate aqueous foams and fiber foams. The aim of the present study was to investigate the effect of impeller geometry on dynamic foam generation in a 60 L mixing tank. Three impeller geometries including two radial—Rushton turbine (RT), Bakker turbine (BT6), one axial high solidity pitched blade turbine (HSPBT), and four dual impeller combinations were investigated. Compressed air, water and sodium dodecyl sulphate were used as gas phase, liquid phase and surfactant, respectively, to generate aqueous foam. 1% mass consistency softwood fiber was used to generate fiber foam. The change in aqueous foam density for any given impeller was limited to ± 40 kg/m3 indicating foam density was dictated by impeller type rather than power input. Single impellers generated bubbly liquids whereas dual impellers generated low-density aqueous foams. Besides, stable foam was produced even at low power input compared to single impellers due to increase in impeller swept volume and blade contact area. Addition of fibers increased the foam density by ~ 100–150 kg/m3 and reduced the half-life time by almost threefold for all impellers due to lower air content and higher bubble size. Placement of high shear impeller (BT6) at bottom and down-pumping axial impeller (HSPBT) on top generated fine bubbles.

Effect of density, phonon scattering and nanoporosity on the thermal conductivity of anisotropic cellulose nanocrystal foams

Anisotropic cellulose nanocrystal (CNC) foams with densities between 25 and 130 kg m−3 (CNC25 –CNC130) were prepared by directional ice-templating of aqueous dispersions. Estimates of the solid and gas conduction contributions to the thermal conductivity of the foams using a parallel resistor model showed that the relatively small increase of the radial thermal conductivity with increasing foam density can be attributed to interfacial phonon scattering. The foam wall nanoporosity and, to a lesser extent, the orientation of the CNC particles and alignment of the columnar macropores, also influence the insulation performance of the foams. The insight on the importance of phonon scattering for the thermal insulation properties of nanocellulose foams provides useful guidelines for tailoring nanofibrillar foams for super-insulating applications.

Morphological, thermal and mechanical properties of polypropylene foams via rotational molding

In this work, polypropylene (PP) was foamed via rotational molding using a chemical blowing agent (CBA) based on azodicarbonamide over a range of concentration (0 to 0.5% wt.). The samples were then analyzed in terms of morphological, thermal and mechanical properties. The morphological analysis showed a continuous increase in the average cell size and cell density with increasing CBA content. Increasing the CBA content also led to lower foam density and thermal conductivity. Similarly, all the mechanical properties (tension, flexion and impact) were found to decrease with increasing CBA content. Finally, the efficiency of the rotomolding process was assessed by producing neat PP samples via compression molding. The results showed negligible differences between the rotomolded and compression molded properties at low deformation and rate of deformation indicating that optimal rotomolding conditions were selected.

Kinked Bisamides as Efficient Supramolecular Foam Cell Nucleating Agents for Low-Density Polystyrene Foams with Homogeneous Microcellular Morphology

Polystyrene foams have become more and more important owing to their lightweight potential and their insulation properties. Progress in this field is expected to be realized by foams featuring a microcellular morphology. However, large-scale processing of low-density foams with a closed-cell structure and volume expansion ratio of larger than 10, exhibiting a homogenous morphology with a mean cell size of approximately 10 µm, remains challenging. Here, we report on a series of 4,4′-diphenylmethane substituted bisamides, which we refer to as kinked bisamides, acting as efficient supramolecular foam cell nucleating agents for polystyrene. Self-assembly experiments from solution showed that these bisamides form supramolecular fibrillary or ribbon-like nanoobjects. These kinked bisamides can be dissolved at elevated temperatures in a large concentration range, forming dispersed nano-objects upon cooling. Batch foaming experiments using 1.0 wt.% of a selected kinked bisamide revealed that the mean cell size can be as low as 3.5 µm. To demonstrate the applicability of kinked bisamides in a high-throughput continuous foam process, we performed foam extrusion. Using 0.5 wt.% of a kinked bisamide yielded polymer foams with a foam density of 71 kg/m3 and a homogeneous microcellular morphology with cell sizes of ≈10 µm, which is two orders of magnitude lower compared to the neat polystyrene reference foam with a comparable foam density.

Experimental investigation of pull-out performance of pedicle screws at different polyurethane (PU) foam densities

Pedicle bone screws are one of the most critical materials used in spinal orthopaedic operations. Screw loosening and pull-out (PO) are basic complications encountered during or after surgery. Pull-out Strength (POS) of the bone is one of the significant parameters to understand the mechanical behaviour of a screw fixed to poor quality or osteoporotic bone. This study investigates how the POS of a pedicle screw is affected by the factors of the screw diameter and the polyurethane (PU) foam density by experimental analysis. In the experiments, two different diameter (5.5 and 6.5 mm) of conical pedicle screws and five different density (0.08, 0.16, 0.24, 0.32 and 0.48 g·cm−3) PU foams were used. According to the force-displacement curves obtained from experimental results, the POS increased with the increases in screw diameter and PU foam density.

Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.