scholarly journals Experimental Investigation on Strength and Failure Characteristics of Cemented Paste Backfill

2021 ◽  
Vol 8 ◽  
Author(s):  
Zhihong Zhang ◽  
Jiacheng Li
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
Uniaxial Compressive Strength ◽  
Cement Content ◽  
Confining Pressure ◽  
Curing Temperature ◽  
Cemented Paste Backfill ◽  
Upward Trend ◽  
Paste Backfill ◽  
Curing Age

The strength characteristics of cemented paste backfill (CPB) in mining areas are key control factors for the safety assessment of overlying strata. A series of experiments about uniaxial compression and triaxial compression were carried out to study the influence of cement content of filling slurry, curing age, and curing temperature on strength behavior of CPB specimens. The failure mechanism and damage feature of CPB have been investigated. The results show the following: (1) The uniaxial compressive strength of CPB specimens exhibits an upward trend with the increase of cement content and curing age. When the cement content is high, the uniaxial compressive strength increases sharply with increasing curing age. (2) The cohesion of CPB specimens increases with the increase of cement content of filling slurry, curing age, and curing temperature. The cohesion of CPB specimens with curing age 7 days and 14 days increases linearly with increasing cement content. At the later stage of curing age, the strength growth of high cement content backfill is significantly greater than that of low cement content. The internal friction angle of the filling increases slightly with increasing filling cement content, curing age, and curing temperature. (3) The shear strength of CPB specimens at curing age 7 days exhibits an upward trend with the increase of confining pressure, while the shear strength at 14 days and 28 days curing age decreases slightly as the confining pressure increases. (4) With the increase of cement content in backfill, the brittleness increases significantly when the backfill is damaged. The failure mode of CPB specimens changes from monoclinic section shear failure to X-type failure with increasing curing age, and the failure process is divided into four stages: pore compaction, linear elastic deformation, plastic deformation, and post-peak failure.

scholarly journals Influence of Binder Types and Temperatures on the Mechanical Properties and Microstructure of Cemented Paste Backfill

2021 ◽  
Vol 2021 ◽  
pp. 1-10 ◽  
Author(s):  
Zhaowen Du ◽  
Shaojie Chen ◽  
Sheng Wang ◽  
Rui Liu ◽  
Dehao Yao ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Microstructural Evolution ◽  
Red Mud ◽  
Hydration Product ◽  
Curing Temperature ◽  
Hydration Reaction ◽  
Burial Depth ◽  
Cemented Paste Backfill ◽  
Paste Backfill

In order to study the influence of burial depth or fire on the core area of cemented paste backfill (CPB), the experiment of CPB with different types of binder and temperature was carried out. Three types of binders, red mud (RM), Portland cement (PC), and slag cement (SC), are used and tested at 20°C, 40°C, 60°C, and 80°C. The macroperformance and microstructural evolution of CPB are analyzed using slump, uniaxial compressive strength (UCS), X-ray diffraction, and scanning electron microscopy (SEM). The results show that the coupled effects of binder type and temperature have a significant impact on the macroscopic performance and microstructural evolution of CPB. The CPB slump prepared with three types of binder meets the production requirement of the mine. Regardless of curing temperature and curing time, the uniaxial compressive strength of CPB samples with PC and SC is much higher than that of CPB samples with red mud. When cured for 12 hours, the uniaxial compressive strength of CPB samples containing PC and SC increases first, then decreases, and finally increases again with the increase of temperature. However, with the increase of temperature, the uniaxial compressive strength of CPB samples containing RM only increases first and then decreases. When the curing temperature is less than 40°C, the main reason for the increase in UCS was attributed to the fact that the temperature increase accelerates the hydration reaction and improves the density of the sample. When the curing temperature is 60°C, the main reason for the decrease in UCS is the formation of the expansive ettringite (AFt) which destroys the internal spatial structure of the sample. When the curing temperature is 80°C, the UCS increases again due to the fact that such high temperature can destroy the crystal structure of AFt and harden the hydration product C-S-H gel.

scholarly journals Study on Microstructural Evolution and Strength Growth and Fracture Mechanism of Cemented Paste Backfill

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Jian-Xin Fu ◽  
Wei-Dong Song ◽  
Yu-Ye Tan
Keyword(s):  
Residual Strength ◽  
Mass Fraction ◽  
Solid Phase ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Cemented Paste Backfill ◽  
X Ray Diffraction ◽  
Pressure Peak ◽  
Paste Backfill ◽  
Curing Age

The relations among the uniaxial compressive strength of cemented paste backfill (CPB) with solid phase mass fraction, cement sand ratio, and curing age were studied. The UCS of CPB samples increased exponentially with the increase of solid phase mass fraction and curing age but increased linearly with the increase of cement sand ratio. The results of X-ray diffraction (XRD) and scanning electron microscope (SEM) showed that the strength was determined by the amount of ettringite and C-S-H gelling. With the increase of ettringite and C-S-H gelling, the strength became larger. The triaxial compression test was conducted by selecting four kinds of CPB samples. The results showed that, with the increase of confining pressure, peak and residual strength became larger, but the elastic modulus decreased. When the ratio of confining pressure and uniaxial strength is about 1 : 2, the CPB samples show significant ductility characteristics and the ratio of residual strength and peak strength increased obviously.

scholarly journals Investigating the Effect of Solid Components on Yield Stress for Cemented Paste Backfill via Uniform Design

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yong Wang ◽  
Aixiang Wu ◽  
Lianfu Zhang ◽  
Fei Jin ◽  
Xiaohui Liu
Keyword(s):  
Yield Stress ◽  
Mass Fraction ◽  
Cement Content ◽  
Uniform Design ◽  
Free Water ◽  
Experimental Program ◽  
Cemented Paste Backfill ◽  
Free Water Content ◽  
Key Factor ◽  
Paste Backfill

Cemented paste backfill (CPB) technology has been applied quite popular around the world. Yield stress is a key factor determining whether CPB could be transported. In order to reveal the effect of solid components on yield stress of CPB, a uniform design experimental program (four factors and six levels) was conducted to test the rheological property of a mine’s CPB. The tested four factors including mass fraction, cement versus other solids ratio, coarse tailings, and gravel contents were considered during the experiment design. Likewise, six experimental levels were given to each factor. Results of the test show that yield stress increased with the mass fraction and cement content. However, the trend reversed for the content of coarse tailings and gravel. Contribution of the four factors to yield stress in descending order is mass fraction > content of gravel > content of coarse tailings > cement versus other tailings ration. Effect of solid components on the yield stress of CPB is mainly due to the different flocculation structure inside the CPB. These various flow structures result in the different free-water content of CPB, leading to a different yield stress value.

Investigation of some controllable factors that impact the stress state in cemented paste backfill

2015 ◽  
Vol 52 (12) ◽  
pp. 1901-1912 ◽  
Author(s):  
James P. Doherty ◽  
Alsidqi Hasan ◽  
Gonzalo H. Suazo ◽  
Andy Fourie
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Cement Content ◽  
Water Pressure ◽  
Cemented Paste Backfill ◽  
Total Stress ◽  
Rest Periods ◽  
Rate Of Increase ◽  
Controllable Factors ◽  
Paste Backfill

This paper presents in-stope measurements of total stress and pore-water pressure at strategic locations within three underground stopes at the Raleigh mine site (Western Australia) that were filled with cemented paste backfill (CPB). The three stopes were very similar in shape. Key differences among the stopes were the filling and resting schedules, the barricade drainage systems used, and the cement content of the CPB. Data from the stopes are compared to determine which controllable factors most significantly influence barricade pressures during and after filling. The most significant factor was the scheduling of rest periods between filling, with even very short pauses in filling dramatically reducing the rate of increase of pore-water pressure and total stress with increasing height of fill.

Sign in / Sign up

Export Citation Format

Share Document