scholarly journals Creep Modelling of Rootstock during Holding in Watermelon Grafting

Agriculture ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1266
Author(s):  
Kang Wu ◽  
Jianzhong Lou ◽  
Chen Li ◽  
Wei Luo ◽  
Congcong Li ◽  
...  
Keyword(s):  
Creep Deformation ◽  
Viscoelastic Model ◽  
Mechanical Damage ◽  
Viscoelastic Behavior ◽  
Damage Mechanism ◽  
Deformation Characteristics ◽  
Mechanical Compression ◽  
Creep Tests ◽  
Viscoelastic Parameters ◽  
Test Velocity

The fragile structure of a rootstock predisposes the stem to mechanical damage during grafting. Thus, it is necessary to take into account the rootstock’s rheological properties under mechanical compression when designing a clamping mechanism. This study focused on cucurbit, a typical rootstock for watermelon grafting. Firstly, we adopted a four-element Burgers model to analyze viscoelastic behavior and deformation characteristics of the rootstock, then conducted creep tests to obtain the parameters of the viscoelastic model. Next, we developed a model for the rootstock during holding based on viscoelastic parameters, loading force and contact time. Moreover, we evaluated the effect of various loading forces and test velocities on creep deformation to reveal the least damage on the rootstock. Results showed that the influence of loading force on the creep deformation was greater than test velocity. Finally, the holding test indicated that the clamping mechanism with silicone rubber can effectively prevent the damage to the stem. Specifically, the loading force should be controlled below 4 N to reduce the associated damage. Taken together, our findings provide a theoretical basis for analyzing the holding damage mechanism during watermelon grafting.

scholarly journals Identification and Frequency Dependence of Viscoelastic Parameters during Dynamic Creep Tests on Selected Pome Fruits

2019 ◽  
Vol 1 (3) ◽  
pp. 324-331 ◽  
Author(s):  
Csaba Farkas ◽  
László Fenyvesi ◽  
Károly Petróczki
Keyword(s):  
Viscoelastic Model ◽  
Model Parameters ◽  
Variable Load ◽  
Pome Fruit ◽  
Creep Tests ◽  
Viscoelastic Parameters ◽  
Wide Range ◽  
Dynamic Creep ◽  
Pome Fruits ◽  
Compressive Loads

In this paper, a novel control-loop concept is presented to investigate the viscoelastic properties of different pome fruits. Repeated mechanical effects are one of the most important risk factors during the postharvest procedures, so our work aimed to expand knowledge in the field. The actual investigations involved Golden Delicious apples and Packham pears. The developed model is based on the Poynting–Thomson body and, during the validating dynamic creep tests, different repeated compressive loads were applied. The examined frequencies were chosen from the most common components of the frequency distribution during the transportation process; the given range is responsible for the highest volume of fruit damage and the most extensive losses. The identified mathematical system determines the viscoelastic model parameters with the best fit to the measured creep data. The model properties of the tested fruit textures are compared in six different frequency setups, with the inspected pome species showing different elastic and viscous responses for the adjusted load conditions. The custom testing device with variable load functions and the proposed solution allow system identification with a wide range of setup possibilities. The resulted viscoelastic parameters can be used for further failure analysis and for the comparison of different pome fruit materials.

scholarly journals Modeling the Viscoelastic Behavior of Quartz and Clay Minerals in Shale by Nanoindentation Creep Tests

Geofluids ◽  
2022 ◽  
Vol 2022 ◽  
pp. 1-16
Author(s):  
Jianfeng Wang ◽  
Yuke Liu ◽  
Chao Yang ◽  
Wenmin Jiang ◽  
Yun Li ◽  
...  
Keyword(s):  
Clay Minerals ◽  
Peak Load ◽  
Viscoelastic Behavior ◽  
Optical Microscope ◽  
Viscoelastic Deformation ◽  
Creep Tests ◽  
Viscoelastic Models ◽  
Small Peak ◽  
Viscoelastic Parameters ◽  
Regression Parameters

The viscoelastic behavior of minerals in shales is important in predicting the macroscale creep behavior of heterogeneous bulk shale. In this study, in situ indentation measurements of two major constitutive minerals (i.e., quartz and clay) in Longmaxi Formation shale from the Sichuan Basin, South China, were conducted using a nanoindentation technique and high-resolution optical microscope. Firstly, quartz and clay minerals were identified under an optical microscope based on their morphology, surface features, reflection characteristics, particle shapes, and indentation responses. Three viscoelastic models (i.e., three-element Voigt, Burger’s, and two-dashpot Kelvin models) were then used to fit the creep data for both minerals. Finally, the effects of peak load on the viscoelastic behavior of quartz and clay minerals were investigated. Our results show that the sizes of the residual imprints on clay minerals were larger than that of quartz for a specific peak load. Moreover, the initial creep rates and depths in clay minerals were higher than those in quartz. However, the creep rates of quartz and clay minerals displayed similar trends, which were independent of peak load. In addition, all three viscoelastic models produced good fits to the experimental data. However, due to the poor fit in the initial holding stage of the three-element Voigt model and instability of the two-dashpot Kelvin model, Burger’s model is best in obtaining the regression parameters. The regression results indicate that the viscoelastic parameters obtained by these models are associated with peak load, and that a relatively small peak load is more reliable for the determination of viscoelastic parameters. Furthermore, the regression values for the viscoelastic parameters of clay minerals were lower than those of quartz and the bulk shale, suggesting the former facilitates the viscoelastic deformation of shale. Our study provides a better understanding of the nanoscale viscoelastic properties of shale, which can be used to predict the time-dependent deformation of shale.

scholarly journals Experimental Study on Fatigue-Creep of P/M FGH96 Superalloy with Different Holding Time

2020 ◽  
Vol 38 (4) ◽  
pp. 873-880
Author(s):  
Yang Xiao ◽  
Haiqin Qin ◽  
Kejun Xu ◽  
Yongqi Wang
Keyword(s):  
Creep Deformation ◽  
Low Cycle Fatigue ◽  
Strain Curve ◽  
Creep Damage ◽  
Holding Time ◽  
Hysteresis Curve ◽  
Transgranular Fracture ◽  
Deformation Characteristics ◽  
Creep Life ◽  
Creep Tests

The fatigue-creep deformation characteristics and evolutions of microstructure of P/M superalloy FGH96 widely used for the turbine disc of an aero-engine were investigated experimentally. The low cycle fatigue-creep tests with different holding times were performed at 550℃. The influence of the holding time on the stress-strain curve, cyclic strain response, fatigue-creep life and damage mechanism were discussed. The results reveal that the holding time has a significant effect on the fatigue-creep deformation characteristics. As the holding time increases, the hysteretic energy of inelastic strain rises, the steady-state hysteresis curve shifts to the right and the envelope strain and the envelope strain rate increase. Fatigue-creep life decreases firstly exponentially and then stabilizes. The creep damage gradually plays a leading role. The fracture analysis indicates that the introduction of the holding time makes the section appear as a multi-crack source. The fracture mode changes from transgranular fracture to transgranular-intergranular mixed fracture. The slip bands and a small amount of dimples appear in the crack propagation zone and the dimple characteristics of the transient fracture zone are obvious.

Identification of Nonlinear Viscoelastic Models of Flexible Polyurethane Foam From Uniaxial Compression Data

2016 ◽  
Vol 138 (2) ◽  
Author(s):  
Yousof Azizi ◽  
Patricia Davies ◽  
Anil K. Bajaj
Keyword(s):  
Uniaxial Compression ◽  
Viscoelastic Model ◽  
Viscoelastic Behavior ◽  
Model Parameters ◽  
Viscoelastic Models ◽  
Nonlinear Viscoelastic ◽  
Compression Data ◽  
Computationally Intensive ◽  
Nonlinear Viscoelastic Model ◽  
Flexible Polyurethane

Flexible polyethylene foam is used in many engineering applications. It exhibits nonlinear and viscoelastic behavior which makes it difficult to model. To date, several models have been developed to characterize the complex behavior of foams. These attempts include the computationally intensive microstructural models to continuum models that capture the macroscale behavior of the foam materials. In this research, a nonlinear viscoelastic model, which is an extension to previously developed models, is proposed and its ability to capture foam response in uniaxial compression is investigated. It is hypothesized that total stress can be decomposed into the sum of a nonlinear elastic component, modeled by a higher-order polynomial, and a nonlinear hereditary type viscoelastic component. System identification procedures were developed to estimate the model parameters using uniaxial cyclic compression data from experiments conducted at six different rates. The estimated model parameters for individual tests were used to develop a model with parameters that are a function of strain rates. The parameter estimation technique was modified to also develop a comprehensive model which captures the uniaxial behavior of all six tests. The performance of this model was compared to that of other nonlinear viscoelastic models.

scholarly journals Viscoelastic behavior of a casing material and its utilization in premium connections in high-temperature gas wells

2018 ◽  
Vol 10 (12) ◽  
pp. 168781401881745 ◽  
Author(s):  
Ying Zhang ◽  
Zhanghua Lian ◽  
Mi Zhou ◽  
Tiejun Lin
Keyword(s):  
High Temperature ◽  
Contact Pressure ◽  
Viscoelastic Model ◽  
Viscoelastic Behavior ◽  
Element Model ◽  
Gas Production ◽  
Prony Series ◽  
Gas Well ◽  
Gas Leakage ◽  
High Temperature Gas

At the high or extra-high temperatures in a natural gas oilfield, where the premium connection is employed by casing, gas leakage in the wellbore is always detected after several years of gas production. As the viscoelastic material’s mechanical properties change with time and temperature, the relaxation of the contact pressure on the connection sealing surface is the main reason for the gas leakage in the high-temperature gas well. In this article, tension-creep experiments were conducted. Furthermore, a constitutive model of the casing material was established by the Prony series method. Moreover, the Prony series’ shift factor was calculated to study the thermo-rheological behavior of the casing material ranging from 120°C to 300°C. A linear viscoelastic model was implemented in ABAQUS, and the simulation results are compared to our experimental data to validate the methodology. Finally, the viscoelastic finite element model is applied to predict the relaxation of contact pressure on the premium connections’ sealing surface versus time under different temperatures. And, the ratio of the design contact pressure and the intending gas sealing pressure is recommended for avoiding the premium connections failure in the high-temperature gas well.

Investigation on Creep Behavior of Grade 91 Heat-Resistant Steel at 923K

2016 ◽  
Vol 853 ◽  
pp. 163-167
Author(s):  
Fa Cai Ren ◽  
Xiao Ying Tang
Keyword(s):  
Creep Rate ◽  
Creep Behavior ◽  
Creep Deformation ◽  
Deformation Behavior ◽  
Minimum Creep Rate ◽  
Resistant Steel ◽  
Creep Tests ◽  
Heat Resistant Steel ◽  
Heat Resistant ◽  
Grade 91

Creep deformation behavior of SA387Gr91Cl2 heat-resistant steel used for steam cooler has been investigated. Creep tests were carried out using flat creep specimens machined from the normalized and tempered plate at 973K with stresses of 100, 125 and 150MPa. The minimum creep rate and rupture time dependence on applied stress was analyzed. The analysis showed that the heat-resistant steel obey Monkman-Grant and modified Monkman-Grant relationships.

A Rational Methodology for Determination of Service Life for a Delayed Coker Drum

2015 ◽  
Author(s):  
John J. Aumuller ◽  
Jie Chen ◽  
Vincent A. Carucci
Keyword(s):  
Service Life ◽  
Low Cycle Fatigue ◽  
Damage Model ◽  
Mechanical Damage ◽  
Damage Mechanism ◽  
Modern Trend ◽  
Cold Spot ◽  
Chromium Alloy ◽  
Cycle Fatigue ◽  
Service Environment

Delayed unit coker drums operate in a severe service environment that precludes long term reliability due to excessive shell bulging and cracking of shell joint and shell to skirt welds. Thermal fatigue is recognized as the leading damage mechanism and past work has provided an idealized description of the thermo-mechanical mechanism via local hot and cold spot formation to quantify a lower bound life estimate for shell weld failure. The present work extends this idealized thermo-mechanical damage model by evaluating actual field data to determine a potential upper bound life estimate. This assessment also provides insight into practical techniques for equipment operators to identify design and operational opportunities to extend the service life of coke drums for their specific service environments. A modern trend of specifying higher chromium and molybdenum alloy content for drum shell material in order to improve low cycle fatigue strength is seen to be problematic; rather, the use of lower alloy materials that are generally described as fatigue tough materials are better suited for the high strain-low cycle fatigue service environment of coke drums. Materials such as SA 204 C (C – ½ Mo) and SA 302 B (C – Mn – ½ Mo) or SA 302 C (C – Mn – ½ Mo – ½ Ni) are shown to be better candidates for construction in lieu of low chromium alloy steel materials such as SA 387 grades P11 (1¼ Cr – ½ Mo), P12 (1 Cr – ½ Mo), P22 (2¼ Cr – 1 Mo) and P21 (3 Cr – 1 Mo).

Rate Dependence and Short-Term Creep Behavior of a Thermoset Polymer at Elevated Temperature

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
C. M. Falcone ◽  
M. B. Ruggles-Wrenn
Keyword(s):  
Creep Behavior ◽  
Viscoelastic Model ◽  
Rate Sensitivity ◽  
Monotonic Loading ◽  
Stress Rate ◽  
Creep Tests ◽  
Strain Behavior ◽  
Thermoset Polymer ◽  
Term Creep ◽  
Prior Stress

The inelastic deformation behavior of PMR-15 neat resin, a high-temperature thermoset polymer, was investigated at 288°C. The effect of loading rate on monotonic stress-strain behavior as well as the effect of prior stress rate on creep behavior were explored. Positive nonlinear rate sensitivity was observed in monotonic loading. Creep response was found to be significantly influenced by prior stress rate. The effect of loading history on creep was studied in stepwise creep tests, where specimens were subjected to a constant stress rate loading followed by unloading to zero stress with intermittent creep periods on both loading and unloading paths. The strain-time response was strongly influenced by prior deformation history. Negative creep was observed on the unloading path. In addition, the behavior of the material was characterized in terms of a nonlinear viscoelastic model by means of creep and recovery tests at 288°C. The model was employed to predict the response of the material under monotonic loading/unloading and multistep load histories.

Change in Creep Deformation of PST Crystals with Different Stress Axes

2006 ◽  
Vol 980 ◽  
Author(s):  
Xiaohua Min ◽  
Eisaku Sakurada ◽  
Masao Takeyama ◽  
Takashi Matsuo
Keyword(s):  
Creep Rate ◽  
Slip System ◽  
Initial Stress ◽  
Creep Deformation ◽  
Strain Curve ◽  
Stage I ◽  
Stress Axis ◽  
Creep Tests ◽  
Transient Stage ◽  
Stereographic Triangle

AbstractBased on our analysis of a lot of creep rate-strain curves of PST crystals with the different angles between the lamellar plate and the stress axis, designated as ø, it was confirmed that the creep rate and the creep deformation manner strongly depend on the ø. It was supposed that the predominant creep deformation using γ plate during the transient stage is derived by the fully suppression of the operation of another slip systems not parallel to γ plate through α2 plate. It was also confirmed that the initial stress axes of the PST crystals within the standard stereographic triangle move for the [001]-[111] line, and then turn their directions for [111] pole during the transient stage. This moving manner of the stress axis indicated that the first slip system of [101](111) continues to the area near the [001]-[111] line in the standard stereographic triangle, and then, the second slip system of [110](111) operates. By comparing this moving manner to the creep rate-strain curve, it is suggested that the first slip system of [101](111) operates during the Stage I where the light decrease in the creep rate remains, after that, the second slip system of [110](111) appears and leads to steep decrease in the creep rate. This stage was designated as the Stage II. According to this conception, it is supposed that the strain at the end of the Stage I is directly correlated with the angle from the initial stress axis to the [001]-[111] line in the standard stereographic triangle. In this study, this supposition was confirmed by conducting the creep tests at 1148 K/68.6 MPa using two PST crystals with ø of 31° and 34°. The initial stress axis of the PST crystal with ø of 31° locates nearer to the [001]-[-111] line than that of the PST crystal with ø of 34°. The strain at the end of the Stage I of the PST crystal with ø of 31° is half that of the PST crystal with ø of 34°. By analyzing the inverse pole figures of the creep interrupted PST crystals, it was confirmed that the angle from the initial stress axis to the [001]-[111] line is correlated with the strain of the transient stage.

Finite deformation and fractional order viscoelasticity of an auxetic foam

2022 ◽  
pp. 1045389X2110643
Author(s):  
Eugenia Stanisauskis ◽  
Paul Miles ◽  
William Oates
Keyword(s):  
Fractional Order ◽  
Finite Deformation ◽  
Viscoelastic Behavior ◽  
Integer Order ◽  
Relaxation Effects ◽  
Viscoelastic Parameters ◽  
Rate Dependent ◽  
Improve Model ◽  
Model Predictions ◽  
And Performance

Auxetic foams exhibit novel mechanical properties due to their unique microstructure for improved energy-absorption and cavity expansion applications that have fascinated the scientific community since their inception. Given the advancements in material processing and performance of polymer open cell auxetic foams, there is a strong desire to fully understand the nonlinear rate-dependent deformation of these materials. The influence of nonlinear compressibility is introduced here along with relaxation effects to improve model predictions for different stretch rates and finite deformation regimes. The viscoelastic behavior of the material is analyzed by comparing fractional order and integer order calculus models. All results are statistically validated using maximum entropy methods to obtain Bayesian posterior densities for the hyperelastic, auxetic, and viscoelastic parameters. It is shown that fractional order viscoelasticity provides [Formula: see text]–[Formula: see text] improvement in prediction over integer order viscoelastic models when the model is calibrated at higher stretch rates where viscoelasticity is more significant.

Sign in / Sign up

Export Citation Format

Share Document