Physics of Within-Tissue Wave Propagation Generated by Pulse Propagation in the Carotid Artery

(1) Background: We aimed to assess the validity of laser Doppler vibrometry (LDV) as an emerging method to measure the local pulse wave velocity (PWV) from skin displacement generated by the pressure pulse inside an underlying artery. (2) Methods: A finite element model representing a simplified common carotid artery embedded within a soft tissue mimicking material was used to reproduce how tissue motions due to a wave propagation along the artery radiates to the skin surface. A parametric study was set up, varying: (i) the pressure conditions inside the artery (shock and traveling pressure impulse), (ii) the arterial depth and (iii) the geometry in a patient-specific artery model. (3) Results: under all conditions, the arterial pulse induced primary and secondary waves at the skin surface; of which the propagation speed deviated from the imposed PWV (deviations between −5.0% to 47.0% for the primary wave front). (4) Conclusions: the propagation of a short pressure impulse induced complex skin displacement patterns revealing a complicated link between PWV and measured propagation speeds at the skin surface. Wave propagation at the skin level may convey information about arterial PWV, however, advanced signal analysis techniques will be necessary to extract local PWV values.

Download Full-text

Patient-specific treatment allocation for carotid artery disease

Interventional Cardiology ◽

10.2217/ica.09.8 ◽

2009 ◽

Vol 1 (1) ◽

pp. 41-49

Author(s):

Marc Bosiers ◽

Koen Deloose ◽

Jurgen Verbist ◽

Patrick Peeters

Keyword(s):

Carotid Artery ◽

Carotid Artery Disease ◽

Specific Treatment ◽

Patient Specific ◽

Treatment Allocation ◽

Artery Disease

Download Full-text

Influence of the applied pressure of the transducer on the propagation speed of the ultrasonic wave in wood

Holzforschung ◽

10.1515/hf-2020-0272 ◽

2021 ◽

Vol 0 (0) ◽

Author(s):

Edgar V.M. Carrasco ◽

Rejane C. Alves ◽

Mônica A. Smits ◽

Vinnicius D. Pizzol ◽

Ana Lucia C. Oliveira ◽

...

Keyword(s):

Wave Propagation ◽

Applied Pressure ◽

Pressure Gauge ◽

Eucalyptus Grandis ◽

Propagation Speed ◽

Ultrasonic Waves ◽

Ultrasonic Speed ◽

Wave Propagation Speed ◽

Propagation Technique ◽

Non Destructive

Abstract The non-destructive wave propagation technique is used to estimate the wood’s modulus of elasticity. The propagation speed of ultrasonic waves is influenced by some factors, among them: the type of transducer used in the test, the form of coupling and the sensitivity of the transducers. The objective of the study was to evaluate the influence of the contact pressure of the transducers on the ultrasonic speed. Ninety-eight tests were carried out on specimens of the species Eucalyptus grandis, with dimensions of 120 × 120 × 50 mm. The calibration of the pressure exerted by the transducer was controlled by a pressure gauge using a previously calibrated load cell. The robust statistical analysis allowed to validate the experimental results and to obtain consistent conclusions. The results showed that the wave propagation speed is not influenced by the pressure exerted by the transducer.

Download Full-text

Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

Science Progress ◽

10.1177/0036850420987058 ◽

2021 ◽

Vol 104 (1) ◽

pp. 003685042098705

Author(s):

Xinran Wang ◽

Yangli Zhu ◽

Wen Li ◽

Dongxu Hu ◽

Xuehui Zhang ◽

...

Keyword(s):

Large Scale ◽

Three Dimensional ◽

Element Model ◽

Rotor System ◽

Dynamic Responses ◽

System Response ◽

Rotating Speed ◽

Torque Load ◽

Set Up ◽

Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

Download Full-text

Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

Scientific Reports ◽

10.1038/s41598-021-93821-5 ◽

2021 ◽

Vol 11 (1) ◽

Author(s):

Niksa Mohammadi Bagheri ◽

Mahmoud Kadkhodaei ◽

Shiva Pirhadi ◽

Peiman Mosaddegh

Keyword(s):

Clinical Data ◽

Three Dimensional ◽

Element Model ◽

Von Mises Stress ◽

Patient Specific ◽

Average Error ◽

Constant Thickness ◽

Arc Length ◽

Implementation Techniques ◽

Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

Download Full-text

Wave propagation improvement in two-dimensional bond-based peridynamics model

Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science ◽

10.1177/0954406220985551 ◽

2021 ◽

pp. 095440622098555

Author(s):

Reza Alebrahim ◽

Pawel Packo ◽

Mirco Zaccariotto ◽

Ugo Galvanetto

Keyword(s):

Wave Propagation ◽

Dynamic Performance ◽

Numerical Dispersion ◽

Motion Modeling ◽

Minimization Method ◽

Irregular Wave ◽

Point Collocation ◽

Potential Applications ◽

Non Local ◽

Set Up

In this study, methods to mitigate anomalous wave propagation in 2-D Bond-Based Peridynamics (PD) are presented. Similarly to what happens in classical non-local models, an irregular wave transmission phenomenon occurs at high frequencies. This feature of the dynamic performance of PD, limits its potential applications. A minimization method based on the weighted residual point collocation is introduced to substantially extend the frequency range of wave motion modeling. The optimization problem, developed through inverse analysis, is set up by comparing exact and numerical dispersion curves and minimizing the error in the frequency-wavenumber domain. A significant improvement in the wave propagation simulation using Bond-Based PD is observed.

Download Full-text

Corrosion of Steel Rebars in Anoxic Environments. Part II: Pit Growth Rate and Mechanical Strength

Materials ◽

10.3390/ma14102547 ◽

2021 ◽

Vol 14 (10) ◽

pp. 2547

Author(s):

Elena Garcia ◽

Julio Torres ◽

Nuria Rebolledo ◽

Raul Arrabal ◽

Javier Sanchez

Keyword(s):

Mechanical Strength ◽

Chloride Content ◽

Element Model ◽

Offshore Structures ◽

Anoxic Environments ◽

Electrochemical Parameters ◽

Cathode Area ◽

Optical Profilometer ◽

Set Up ◽

Corrosion Of Steel

Reinforced concrete may corrode in anoxic environments such as offshore structures. Under such conditions the reinforcement fails to passivate completely, irrespective of chloride content, and the corrosion taking place locally induces the growth of discrete pits. This study characterised such pits and simulated their growth from experimentally determined electrochemical parameters. Pit morphology was assessed with an optical profilometer. A finite element model was developed to simulate pit growth based on electrochemical parameters for different cathode areas. The model was able to predict long-term pit growth by deformed geometry set up. Simulations showed that pit growth-related corrosion tends to maximise as cathode area declines, which lower the pitting factor. The mechanical strength developed by the passive and prestressed rebar throughout its service life was also estimated. Passive rebar strength may drop by nearly 20% over 100 years, whilst in the presence of cracking from the base of the pit steel strength may decline by over 40%.

Download Full-text