scholarly journals Corrosion of Steel Rebars in Anoxic Environments. Part II: Pit Growth Rate and Mechanical Strength

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2547
Author(s):  
Elena Garcia ◽  
Julio Torres ◽  
Nuria Rebolledo ◽  
Raul Arrabal ◽  
Javier Sanchez
Keyword(s):  
Mechanical Strength ◽  
Chloride Content ◽  
Element Model ◽  
Offshore Structures ◽  
Anoxic Environments ◽  
Electrochemical Parameters ◽  
Cathode Area ◽  
Optical Profilometer ◽  
Set Up ◽  
Corrosion Of Steel

Reinforced concrete may corrode in anoxic environments such as offshore structures. Under such conditions the reinforcement fails to passivate completely, irrespective of chloride content, and the corrosion taking place locally induces the growth of discrete pits. This study characterised such pits and simulated their growth from experimentally determined electrochemical parameters. Pit morphology was assessed with an optical profilometer. A finite element model was developed to simulate pit growth based on electrochemical parameters for different cathode areas. The model was able to predict long-term pit growth by deformed geometry set up. Simulations showed that pit growth-related corrosion tends to maximise as cathode area declines, which lower the pitting factor. The mechanical strength developed by the passive and prestressed rebar throughout its service life was also estimated. Passive rebar strength may drop by nearly 20% over 100 years, whilst in the presence of cracking from the base of the pit steel strength may decline by over 40%.

scholarly journals Corrosion of Steel Rebars in Anoxic Environments. Part I: Electrochemical Measurements

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2491
Author(s):  
Elena Garcia ◽  
Julio Torres ◽  
Nuria Rebolledo ◽  
Raul Arrabal ◽  
Javier Sanchez
Keyword(s):  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Chloride Content ◽  
Offshore Platforms ◽  
Anoxic Conditions ◽  
Current Limit ◽  
Anoxic Environments ◽  
Corrosion Of Steel ◽  
Steel Rebars

The number of reinforced concrete structures subject to anoxic conditions such as offshore platforms and geological storage facilities is growing steadily. This study explored the behaviour of embedded steel reinforcement corrosion under anoxic conditions in the presence of different chloride concentrations. Corrosion rate values were obtained by three electrochemical techniques: Linear polarization resistance, electrochemical impedance spectroscopy, and chronopotenciometry. The corrosion rate ceiling observed was 0.98 µA/cm2, irrespective of the chloride content in the concrete. By means of an Evans diagram, it was possible to estimate the value of the cathodic Tafel constant (bc) to be 180 mV dec−1, and the current limit yielded an ilim value of 0.98 µA/cm2. On the other hand, the corrosion potential would lie most likely in the −900 mVAg/AgCl to −1000 mVAg/AgCl range, whilst the bounds for the most probable corrosion rate were 0.61 µA/cm2 to 0.22 µA/cm2. The experiments conducted revealed clear evidence of corrosion-induced pitting that will be assessed in subsequent research.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

Finite Element Model of Human Cochlea Considering of the Helicotrema Size

2013 ◽  
Vol 456 ◽  
pp. 576-581 ◽  
Author(s):  
Li Fu Xu ◽  
Na Ta ◽  
Zhu Shi Rao ◽  
Jia Bin Tian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Basilar Membrane ◽  
Round Window ◽  
Element Model ◽  
Oval Window ◽  
Fe Model ◽  
Cochlear Duct ◽  
Human Cochlea ◽  
Set Up

A 2-D finite element model of human cochlea is established in this paper. This model includes the structure of oval window, round window, basilar membrane and cochlear duct which is filled with fluid. The basilar membrane responses are calculated with sound input on the oval window membrane. In order to study the effects of helicotrema on basilar membrane response, three different helicotrema dimensions are set up in the FE model. A two-way fluid-structure interaction numerical method is used to compute the responses in the cochlea. The influence of the helicotrema is acquired and the frequency selectivity of the basilar membrane motion along the cochlear duct is predicted. These results agree with the experiments and indicate much better results are obtained with appropriate helicotrema size.

Study on the Prediction of Drilling Forces on Cortical Bone Based on Finite Element Simulation

2013 ◽  
Vol 589-590 ◽  
pp. 157-162
Author(s):  
Ya Hui Hu ◽  
Qing Yun Zhang ◽  
Xiao Yu Yue
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Feed Rate ◽  
Orthogonal Experiment ◽  
Element Model ◽  
Drilling Speed ◽  
Drilling Force ◽  
Drill Diameter ◽  
Potential Damage ◽  
Set Up

The changes of drilling forces during bone drilling provide a useful index for evaluating the risk of potential damage to the bone. The aim of the work is that an elastic-plastic dynamic finite element model is used to simulate the process of a drill bit drilling through the bone. The finite element model was set up in the Abaqus6.11; the prediction model of the drilling force was gotten by using the regression orthogonal experiment and data processing software Matlab7.0. Diverse values of drilling speed, feed rate and drill diameter are important factors which will lead to changes in the drilling forces. By controlling the drilling parameters can obtain the optimal drilling force. The results show that the diameter has the greatest influence on the drilling force, the drilling speed the second, the feed rate the last.

Study on the Deformation of the Oil-Immersed Transformer Tank by FEA

2011 ◽  
Vol 422 ◽  
pp. 51-54 ◽  
Author(s):  
Jian Hua Zhang ◽  
Ling Yu Sun ◽  
Xiao Jun Zhang ◽  
Jia Peng Li
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Mechanical Strength ◽  
Element Model ◽  
3D Finite Element ◽  
3D Finite Element Model ◽  
Series Of Experiments ◽  
Oil Tank ◽  
Directive Function

The oil-immersed transformer tank is an outside package component of the transformer body. The sealing quality and mechanical strength of the oil tank are affected by the deformation after loading. In this paper, the 3D finite element model of oil-immersed transformer tank is established. The oil-immersed transformer tank deformation is obtained by FEA under the condition of vacuuming. A series of experiments about the deformation of the oil-immersed transformer tank are carried out. Comparing experiment results with FEA results, FEA results are agrees well with the experiments’. It can save the time consumed on designing the oil tank, and has the directive function for the whole design.

Carbon Nanotube Composites for Vibration Damping

2008 ◽  
Vol 47-50 ◽  
pp. 817-820 ◽  
Author(s):  
R.L. Dai ◽  
W.H. Liao
Keyword(s):  
Carbon Nanotube ◽  
Epoxy Resin ◽  
Dynamic Properties ◽  
Element Model ◽  
Vibration Damping ◽  
Segment Length ◽  
Pure Epoxy ◽  
Nanotube Composites ◽  
Carbon Nanotube Composites ◽  
Set Up

It has been found that the composites of carbon nanotubes (CNTs) and epoxy resin could greatly enhance damping ability while the stiffness is kept high. In this paper, carbon nanotube enhanced epoxy resin is fabricated. A testing apparatus for obtaining composite dynamic properties is set up. In particular, the loss factors are measured. Experimental results show that CNT additive can provide the composite with several times higher damping as compared with pure epoxy. A finite element model is built to simulate the composite damping. CNT diameter and segment length are investigated using the developed model. Results show that composite damping is insensitive to CNT segment length while the effect of CNT diameter on composite damping is significant.

Effect of Air Fraction on Force Coefficients in Oscillatory Flow

2021 ◽  
Author(s):  
Malene Hovgaard Vested ◽  
Erik Damgaard Christensen
Keyword(s):  
High Speed ◽  
Offshore Structures ◽  
Air Injection ◽  
Wave Loads ◽  
Morison Equation ◽  
Force Coefficients ◽  
Air Content ◽  
Set Up ◽  
High Level ◽  
Spilling Breakers

Abstract The forces on marine and offshore structures are often affected by spilling breakers. The spilling breaker is characterized by a roller of mixed air and water with a forward speed approximately equal to the wave celerity. This high speed in the top of the wave has the potential to induce high wave loads on upper parts of the structures. This study analyzed the effect of the air content on the forces. The analyses used the Morison equation to examine the effect of the percentage of air on the forces. An experimental set-up was developed to include the injection of air into an otherwise calm water body. The air-injection did introduce a high level a turbulence. It was possible to assess the amount of air content in the water for different amounts of air-injection. In the mixture of air and water the force on an oscillating square cylinder was measured for different levels of air-content, — also in the case without air. The measurements indicated that force coefficients for clear water could be use in the Morison equation as long as the density for water was replaced by the density for the mixture of air and water.

Parameter Sensitivity in Numerical Modelling of Ice-Structure Interaction With Cohesive Element Method

2016 ◽  
Author(s):  
Dianshi Feng ◽  
Sze Dai Pang ◽  
Jin Zhang
Keyword(s):  
Element Model ◽  
Offshore Structures ◽  
Parameter Sensitivity ◽  
The Arctic ◽  
Cohesive Element ◽  
Structure Interaction ◽  
Marine Structure ◽  
Ice Loads ◽  
The Stability ◽  
Element Method

The increasing marine activities in the Arctic has resulted in a growing demand for reliable structural designs in this region. Ice loads are a major concern to the designer of a marine structure in the arctic, and are often the principal factor that governs the structural design [Palmer and Croasdale, 2013]. With the rapid advancement in computational power, numerical method is becoming a useful tool for design of offshore structures subjected to ice actions. Cohesive element method (CEM), a method which has been widely utilized to simulate fracture in various materials ranging from metals to ceramics and composites as well as bi-material systems, has been recently applied to predict ice-structure interactions. Although it shows promising future for further applications, there are also some challenging issues like high mesh dependency, large variation in cohesive properties etc., yet to be resolved. In this study, a 3D finite element model with the use of CEM was developed in LS-DYNA for simulating ice-structure interaction. The stability of the model was investigated and a parameter sensitivity analysis was carried out for a better understanding of how each material parameter affects the simulation results.

scholarly journals Predicting Fusing Current for Encapsulated Wire Bonds under Transient Loads

2010 ◽  
Vol 2010 (1) ◽  
pp. 000486-000493 ◽  
Author(s):  
Aditi Mallik ◽  
Roger Stout
Keyword(s):  
Single Pulse ◽  
Element Model ◽  
Current Response ◽  
Temperature Dependent ◽  
Wire Bonds ◽  
Potential Failure ◽  
Different Dimensions ◽  
Transient Loads ◽  
The Wire ◽  
Set Up

For high power IC chips, as device size inevitably decreases, the wire diameter unfortunately must decrease due to the need of finer pitch wires. Fusing or melting of wirebonds thus increasingly becomes one of the potential failure issues for such IC's. Experiments were performed under transient loads on dummy packages having aluminum, gold, or copper wires of different dimensions. A finite element model was constructed that correlates very well with the observed maximum operating currents for such wirebonds under actual experimental test conditions. A qualitative observation of typical current profiles, as fusing conditions were approached, was that current would reach a maximum value very early in the pulse, and then fall gradually. One goal achieved through the modeling was to show that the current in the wire falls with time due to the heating of the wire material. Correspondingly, the wire reaches the melting temperature not at the peak current but rather at the end of pulse. Further, modeling shows that knowledge of external resistance and inductance of the experimental set up are highly significant in determining the details of a fusing event, but if known along with the temperature-dependent wire properties, the simulation can predict the correct voltage and current response of the part with 2% error. On the other hand, lack of external circuit characteristics may lead to completely incorrect results. For instance, the assumption that current is constant until the wire heats to fusing temperature, or that current and temperature both rise monotonically to maximum values until the wire fuses, are almost certain to be wrong. The work has been carried out for single pulse events as well as pulse trains.

Interaction of external head impact parameters on region and volume of strain for collisions in sport

2018 ◽  
Vol 233 (2) ◽  
pp. 258-267 ◽  
Author(s):  
R Anna Oeur ◽  
Michael D Gilchrist ◽  
Thomas Blaine Hoshizaki
Keyword(s):  
Brain Injuries ◽  
Element Model ◽  
Brain Regions ◽  
Peak Strain ◽  
Centre Of Gravity ◽  
Impact Parameters ◽  
Four Levels ◽  
Set Up ◽  
The Impact ◽  
Strain Responses

Collisions with the head are the primary cause of concussion in contact sports. Head impacts can be further characterized by velocity, striking mass, compliance, and location (direction). The purpose of this study was to describe the interaction effects of these parameters on peak strain in four brain regions and the volume of strain for collision impacts. A pendulum test set-up was used to deliver impacts to an adult Hybrid III headform according to four levels of mass (3, 9, 15, and 21 kg), four velocities (1.5, 3.0, 4.5, and 6.0 m/s), two impact locations (through the centre of gravity and a non-centre of gravity), and three levels of compliance simulating unprotected, helmeted, and well-padded conditions in sport. Headform accelerations were input into a brain finite element model to obtain peak strain in the frontal, temporal, parietal, and occipital lobes and the volume of the brain experiencing 0.10, 0.15, 0.20, and 0.25 strains. Centre-of-gravity impacts created the highest strains (peak and volume) under low compliance and non-centre-of-gravity impacts produced greater strain responses under medium and high compliance conditions. The temporal lobe was the region that consistently displayed the highest peak strains, which may be due to the proximity of the impact locations to this region. Interactions between mass and velocity displayed effects where the 9-kg mass had higher peak and volumes of strain than the 15-kg mass at velocities of 3.0 and 4.5 m/s. This study demonstrates the important role of interacting impact parameters on increasing strain responses that are relevant to the spectrum of diffuse brain injuries, including concussion.

Sign in / Sign up

Export Citation Format

Share Document