scholarly journals Biomechanical Analysis and Design Method for Patient-Specific Reconstructive Implants for Large Bone Defects of the Distal Lateral Femur

Biosensors ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 4
Author(s):  
Po-Kuei Wu ◽  
Cheng-Wei Lee ◽  
Wei-Hsiang Sun ◽  
Chun-Li Lin
Keyword(s):  
Topology Optimization ◽  
Bone Cement ◽  
Fe Analysis ◽  
Biomechanical Analysis ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Internal Cavity ◽  
Solid Core ◽  
Bone Scaffold ◽  
Analysis And Design

This study aims to develop a generalizable method for designing a patient-specific reconstructive scaffold implant for a large distal lateral femur defect using finite element (FE) analysis and topology optimization. A 3D solid-core implant for the distal femur defect was designed to withhold the femur load. Data from FE analysis of the solid implant were use for topology optimization to obtain a ‘bone scaffold implant’ with light-weight internal cavity and surface lattice features to allow for filling with bone material. The bone scaffold implant weighed 69.6% less than the original solid-core implant. The results of FE simulation show that the bone repaired with the bone scaffold implant had lower total displacement (12%), bone plate von Mises stress (34%), bone maximum first principal stress (33%), and bone maximum first principal strain (32%) than did bone repaired with bone cement. The trend in experimental strain with increasing load on the composite femur was greater with bone cement than with the bone scaffold implant. This study presents a generalizable method for designing a patient-specific reconstructive scaffold implant for the distal lateral femur defect that has sufficient strength and space for filling with allograft bone.

scholarly journals Design of a Metal 3D Printing Patient-Specific Repairing Thin Implant for Zygomaticomaxillary Complex Bone Fracture Based on Buttress Theory Using Finite Element Analysis

2020 ◽  
Vol 10 (14) ◽  
pp. 4738
Author(s):  
Yu-Tzu Wang ◽  
Chih-Hao Chen ◽  
Po-Fang Wang ◽  
Chien-Tzung Chen ◽  
Chun-Li Lin
Keyword(s):  
Finite Element ◽  
Topology Optimization ◽  
Biomechanical Analysis ◽  
Patient Specific ◽  
Element Analysis ◽  
Posterior Teeth ◽  
Frontal Process ◽  
Metal 3D Printing ◽  
Stress Variations ◽  
Zygomaticomaxillary Complex

This study developed a zygomaticomaxillary complex (ZMC) patient-specific repairing thin (PSRT) implant based on the buttress theory by integrating topology optimization and finite element (FE) analysis. An intact facial skeletal (IFS) model was constructed to perform topology optimization to obtain a hollow skeleton (HS) model with the structure and volume optimized. The PSRT implant was designed based on the HS contour which represented similar trends as vertical buttress pillars. A biomechanical analysis was performed on a ZMC fracture fixation with the PSRT implant and two traditional mini-plates under uniform axial loads applied on posterior teeth with 250 N. Results indicated that the variation in maximum bone stress and model volume between the IFS and HS models was 15.4% and 75.1%, respectively. Small stress variations between the IFS model and repairing with a PSRT implant (2.75–26.78%) were found for compressive stress at frontal process and tensile stress at the zygomatic process. Comparatively, large stress variations (30.67–96.26%) with different distributions between the IFS model and mini-plate models were found at the corresponding areas. This study concluded that the main structure/contour design of the ZMC repair implant according to the buttress position and orientation can obtain a favorable mechanical behavior.

Biomechanical analysis and design of a dynamic spinal fixator using topology optimization: a finite element analysis

2014 ◽  
Vol 52 (5) ◽  
pp. 499-508 ◽  
Author(s):  
Hung-Ming Lin ◽  
Chien-Lin Liu ◽  
Yung-Ning Pan ◽  
Chang-Hung Huang ◽  
Shih-Liang Shih ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Topology Optimization ◽  
Biomechanical Analysis ◽  
Element Analysis ◽  
Analysis And Design

scholarly journals Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Niksa Mohammadi Bagheri ◽  
Mahmoud Kadkhodaei ◽  
Shiva Pirhadi ◽  
Peiman Mosaddegh
Keyword(s):  
Clinical Data ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Average Error ◽  
Constant Thickness ◽  
Arc Length ◽  
Implementation Techniques ◽  
Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

scholarly journals Evaluation of Bone–Implant Interface Stress and Strain Using Heterogeneous Mandibular Bone Properties Based on Different Empirical Correlations

2021 ◽  
Author(s):  
Mostafa Omran Hussein ◽  
Mohammed Suliman Alruthea
Keyword(s):  
Finite Element ◽  
Group Iv ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Dental Arch ◽  
Stress And Strain ◽  
Bone Implant ◽  
Bone Properties ◽  
Group I ◽  
Von Mises

Abstract Objective The purpose of this study was to compare methods used for calculating heterogeneous patient-specific bone properties used in finite element analysis (FEA), in the field of implant dentistry, with the method based on homogenous bone properties. Materials and Methods In this study, three-dimensional (3D) computed tomography data of an edentulous patient were processed to create a finite element model, and five identical 3D implant models were created and distributed throughout the dental arch. Based on the calculation methods used for bone material assignment, four groups—groups I to IV—were defined. Groups I to III relied on heterogeneous bone property assignment based on different equations, whereas group IV relied on homogenous bone properties. Finally, 150 N vertical and 60-degree-inclined forces were applied at the top of the implant abutments to calculate the von Mises stress and strain. Results Groups I and II presented the highest stress and strain values, respectively. Based on the implant location, differences were observed between the stress values of group I, II, and III compared with group IV; however, no clear order was noted. Accordingly, variable von Mises stress and strain reactions at the bone–implant interface were observed among the heterogeneous bone property groups when compared with the homogenous property group results at the same implant positions. Conclusion Although the use of heterogeneous bone properties as material assignments in FEA studies seem promising for patient-specific analysis, the variations between their results raise doubts about their reliability. The results were influenced by implants’ locations leading to misleading clinical simulations.

Computer assisted evaluation of plate osteosynthesis of diaphyseal femur fracture considering interfragmentary movement: a finite element study

2017 ◽  
Vol 62 (3) ◽  
Author(s):  
Claudia Wittkowske ◽  
Stefan Raith ◽  
Maximilian Eder ◽  
Alexander Volf ◽  
Jan S. Kirschke ◽  
...  
Keyword(s):  
Finite Element ◽  
Plate Osteosynthesis ◽  
Computation Time ◽  
Fe Analysis ◽  
Patient Specific ◽  
Osteoporotic Bone ◽  
Computer Assisted ◽  
Efficient Computation ◽  
User Input ◽  
Patient Specific Modeling

AbstractA semi-automated workflow for evaluation of diaphyseal fracture treatment of the femur has been developed and implemented. The aim was to investigate the influence of locking compression plating with diverse fracture-specific screw configurations on interfragmentary movements (IFMs) with the use of finite element (FE) analysis. Computed tomography (CT) data of a 22-year-old non-osteoporotic female were used for patient specific modeling of the inhomogeneous material properties of bone. Hounsfield units (HU) were exported and assigned to elements of a FE mesh and converted to mechanical properties such as the Young’s modulus followed by a linear FE analysis performed in a semi-automated fashion. IFM on the near and far cortex was evaluated. A positive correlation between bridging length and IFM was observed. Optimal healing conditions with IFMs between 0.5 mm and 1 mm were found in a constellation with a medium bridging length of 80 mm with three unoccupied screw holes around the fracture gap. Usage of monocortical screws instead of bicortical ones had negligible influence on the evaluated parameters when modeling non-osteoporotic bone. Minimal user input, automation of the procedure and an efficient computation time ensured quick delivery of results which will be essential in a future clinical application.

scholarly journals Biomechanical modeling of knee for specific patients with chronic anterior cruciate ligament injury

2013 ◽  
Vol 10 (1) ◽  
pp. 525-545 ◽  
Author(s):  
Nenad Filipovic ◽  
Velibor Isailovic ◽  
Dalibor Nikolic ◽  
Aleksandar Peulic ◽  
Nikola Mijailovic ◽  
...  
Keyword(s):  
Gait Analysis ◽  
Acl Reconstruction ◽  
Cruciate Ligament ◽  
Biomechanical Model ◽  
Element Model ◽  
Gait Pattern ◽  
Von Mises Stress ◽  
Ligament Injury ◽  
Patient Specific ◽  
Reconstruction Technique

In this study we modeled a patient specific 3D knee after anterior cruicate ligament (ACL) reconstruction. The purpose of the ACL reconstruction is to achieve stability in the entire range of motion of the knee and the establishment of the normal gait pattern. We present a new reconstruction technique that generates patient-specific 3D knee models from patient?s magnetic resonant images (MRIs). The motion of the ACL reconstruction patients is measured by OptiTrack system with six infrared cameras. Finite element model of bones, cartilage and meniscus is used for determination stress and strain distribution at different body postures during gait analysis. It was observed that the maximum effective von Mises stress distribution up to 8 MPa occurred during 30% of the gait cycle on the meniscus. The biomechanical model of the knee joint during gait analysis can provide insight into the underlying mechanisms of knee function after ACL reconstruction.

Altered Load Transfer in the Pelvis in the Presence of Periprosthetic Osteolysis

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Jacob T. Munro ◽  
Justin W. Fernandez ◽  
James S. Millar ◽  
Cameron G. Walker ◽  
Donald W. Howie ◽  
...  
Keyword(s):  
Cortical Bone ◽  
Load Transfer ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Fe Model ◽  
Stress Concentrations ◽  
Periprosthetic Osteolysis ◽  
Total Hip ◽  
Long Term Follow Up ◽  
Von Mises

Periprosthetic osteolysis in the retroacetabular region with cancellous bone loss is a recognized phenomenon in the long-term follow-up of total hip replacement. The effects on load transfer in the presence of defects are less well known. A validated, patient-specific, 3D finite element (FE) model of the pelvis was used to assess changes in load transfer associated with periprosthetic osteolysis adjacent to a cementless total hip arthroplasty (THA) component. The presence of a cancellous defect significantly increased (p < 0.05) von Mises stress in the cortical bone of the pelvis during walking and a fall onto the side. At loads consistent with single leg stance, this was still less than the predicted yield stress for cortical bone. During higher loads associated with a fall onto the side, highest stress concentrations occurred in the superior and inferior pubic rami and in the anterior column of the acetabulum with larger cancellous defects.

Sign in / Sign up

Export Citation Format

Share Document